Study guide
5.2 Configuration Deviation List (CDL) & Missing Secondary Airframe Parts
FAA ADX Aircraft Dispatcher Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Regulations & Dispatcher Certification (14 CFR Part 65)
1.1 14 CFR Part 65 Eligibility, Privileges, Limitations & Retesting 1.2 Operational Control & Shared Dispatcher-PIC Responsibility 1.3 Dispatch Release Requirements, Amendments & Records
2 Chapter 2: Part 121 Domestic, Flag & Supplemental Operating Rules
2.1 Domestic vs. Flag vs. Supplemental Operational Rules 2.2 Dispatch Weather Minimums & Departure Rules 2.3 Takeoff Alternates & Clean Aircraft Concept
3 Chapter 3: Destination Alternates, Alternate Minimums & Redispatch
3.1 Destination Alternate Requirements (1-2-3 Rule & Flag/Supplemental) 3.2 Alternate Airport Weather Minimums (OpSpecs Table C055) 3.3 Marginal Weather Rule & Second Alternate Selection 3.4 En Route Redispatch & Reclearance Procedures
4 Chapter 4: Dispatcher & Flightcrew Duty Limitations and Rest (14 CFR § 121.465 & Part 117)
4.1 Dispatcher Duty Time Limitations & Rest Requirements 4.2 Flightcrew Duty & Rest Requirements (14 CFR Part 117) 4.3 Dispatcher Qualifications, Recurrent Training & Operating Familiarization
5 Chapter 5: Minimum Equipment Lists (MEL), CDL & Maintenance Dispatch
5.1 Master Minimum Equipment List (MMEL) & Operator MEL 5.2 Configuration Deviation List (CDL) & Missing Secondary Airframe Parts 5.3 Dispatch with Inoperative Equipment, Logbooks & Special Flight Permits
6 Chapter 6: Aviation Meteorology — Atmosphere, Pressure Systems & Fronts
6.1 Atmospheric Structure, Pressure Systems & Altimetry 6.2 Air Masses & Frontal Systems 6.3 Clouds, Atmospheric Stability & Fog 6.4 Earth Motion, Global Circulation & Regional/Local Weather Regimes
7 Chapter 7: Hazardous Aviation Weather — Convection, Icing & Turbulence
7.1 Thunderstorms & Severe Convection 7.2 Structural & Induction Icing 7.3 Turbulence, Jet Streams & Clear Air Turbulence (CAT) 7.4 Low-Level Windshear & Microburst Detection Systems
8 Chapter 8: Aviation Weather Products, Observations & Forecasts
8.1 Surface Weather Observations (METAR & SPECI) 8.2 Terminal Aerodrome Forecasts (TAF) 8.3 In-Flight Weather Advisories (PIREPs, AIRMETs, SIGMETs) 8.4 Upper-Air Analysis & Prognostic Weather Charts
9 Chapter 9: Airspace Structure, Air Traffic Control & Traffic Management
9.1 Airspace Classes & Operating Rules 9.2 Special Use Airspace & Temporary Flight Restrictions 9.3 Air Traffic Control Flow Management & Initiatives 9.4 NOTAM System & Airport Field Condition Reporting 9.5 Flight Plan Filing: Domestic and International (ICAO) Flight Plans
10 Chapter 10: IFR Navigation, Airway Structure & Charting
10.1 Ground-Based Navigation Facilities (VOR, TACAN, DME, ILS) 10.2 RNAV, RNP & Performance-Based Navigation (PBN) 10.3 En Route IFR Charts & High/Low Airway Navigation 10.4 Earth Reference, Time Standards, Chart Projections & Great-Circle Navigation
11 Chapter 11: Terminal Instrument Procedures — SIDs, STARs & Approaches
11.1 Standard Instrument Departures (SIDs) & Obstacle Departure Procedures (ODPs) 11.2 Standard Terminal Arrival Routes (STARs) & En Route Transitions 11.3 Instrument Approach Procedures & Minimums 11.4 Holding Procedures & Holding Pattern Calculations
12 Chapter 12: High-Altitude Transonic Aerodynamics & Jet Characteristics
12.1 Transonic Flow, Mach Number & Compressibility 12.2 Shock Waves, Mach Tuck & Shock Stall 12.3 Coffin Corner, Buffet Boundaries & Swept-Wing Aerodynamics
13 Chapter 13: Transport Category Turbine Aircraft Systems
13.1 Turbine Powerplants & Auxiliary Power Units 13.2 Electrical, Hydraulic & Pneumatic Systems 13.3 Pressurization, Environmental Control & Oxygen Systems 13.4 Flight Management Systems (FMS), Autoflight & Avionics
14 Chapter 14: Aircraft Weight, Balance & Loading
14.1 Weight Definitions & Structural Limitations 14.2 Center of Gravity (CG) Principles & Computations 14.3 Cargo Loading, Floor Load Limits & Load Manifests
15 Chapter 15: Transport Category Aircraft Performance & Limitations
15.1 Takeoff Performance & V-Speeds 15.2 Climb Gradients, Obstacle Clearance & Runway Limitations 15.3 En Route Engine Inoperative Performance & Drift-Down 15.4 Landing Performance & Runway Condition Assessment
16 Chapter 16: Practical Dispatch Flight Planning, Fuel Strategy & Emergencies
16.1 Domestic, Flag & Supplemental Fuel Requirements 16.2 Flight Planning, Route Selection & Equal Time Point (ETP) / PNR 16.3 Emergency Procedures, In-Flight Diversions & Security Threats 16.4 NTSB Part 830 Incident & Accident Notification Procedures 16.5 Flight Following, Overdue Aircraft & Post-Flight Duties
17 Chapter 17: Human Factors, ADM, CRM & Dispatch Communications
17.1 Human Factors & Human Error in Airline Dispatch 17.2 Aeronautical Decision Making, Judgment & Risk Management 17.3 Crew Resource Management, Dispatch Teamwork & Briefing Technique 17.4 Dispatch Communications, Data Link & Aeronautical Publications
5.2 Configuration Deviation List (CDL) & Missing Secondary Airframe Parts
Key Takeaways Explain This Topic AI
The Configuration Deviation List (CDL) is developed by the aircraft manufacturer and approved by the FAA Aircraft Certification Office (ACO) as an Appendix to the FAA-Approved Airplane Flight Manual (AFM) under 14 CFR Part 25.
The CDL authorizes dispatch with missing external secondary airframe parts and aerodynamic cowlings; primary structural members (spars, frames, skins, control surfaces, pressure vessels) are strictly prohibited from being missing.
Unlike the MEL, the CDL does not utilize calendar repair categories (A, B, C, D); aircraft may be operated with missing CDL items indefinitely until scheduled maintenance, provided all performance limitations and decrements are observed.
CDL limitations include takeoff weight decrements (MTOW), landing weight decrements (MLW), en route climb limit decrements, percentage en route fuel burn increases, and VMO/MMO/altitude restrictions.
Multiple CDL items are cumulative: all weight decrements and percentage fuel burn penalties are additive unless the AFM CDL preamble explicitly specifies otherwise; missing opposing symmetrical parts or multiple parts on the same control surface is generally prohibited.
Last updated: September 2026
5.2 Configuration Deviation List (CDL) & Missing Secondary Airframe Parts
While the Minimum Equipment List (MEL) governs dispatch with inoperative instruments, avionics, and internal aircraft systems, transport category aircraft also experience physical structural wear and damage on external airframe components during daily line operations. Fairings crack, access panels detach, aerodynamic seals tear, and static discharge wicks snap off. Grounding an airliner for a missing non-structural aerodynamic fairing would impose severe operational and economic burdens without enhancing flight safety.
To address this operational reality, aircraft manufacturers and the FAA established the Configuration Deviation List (CDL) . Governed under transport category type certification regulations ( 14 CFR Part 25 ), the CDL establishes the legal conditions, operational limitations, and performance penalties under which an aircraft may be dispatched with missing external secondary airframe parts.
Regulatory Authority & Document Architecture: The AFM Appendix
A critical distinction on the FAA ADX exam concerns the document origin and approving authority of the CDL:
Document Location : The CDL is published as a formal Appendix to the FAA-Approved Airplane Flight Manual (AFM) .
Approving Authority : Because the CDL directly affects the aerodynamic certification and performance data of the aircraft, it is developed by the aircraft manufacturer (e.g., Boeing, Airbus, Bombardier) and approved directly by the FAA Aircraft Certification Office (ACO) .
Legal Status : Because the AFM is a regulatory document approved under 14 CFR Part 25, the limitations and penalties set forth in the CDL carry the force of federal law under 14 CFR § 91.9 and 14 CFR § 121.173 .
Unlike the Operator MEL—which is tailored by each airline and approved by a local Principal Operations Inspector (POI) at a Flight Standards District Office (FSDO)—the CDL is an integral part of the manufacturer's FAA-approved flight manual and is identical across all operators of that exact aircraft model.
Primary Structure vs. Secondary Airframe Structure
The fundamental boundary governing CDL applicability is the engineering classification between primary airframe structure and secondary airframe structure :
Primary Structure (Strictly Excluded from CDL)
Primary airframe structure comprises any structural element that contributes significantly to the carrying of flight, ground, or cabin pressurization loads. Failure or absence of a primary structural component would catastrophically compromise the structural integrity or controllability of the aircraft. Examples include:
- Wing front, rear, and auxiliary spars
- Fuselage frames, longerons, and pressure cabin skins
- Forward and aft pressure bulkheads
- Engine pylon primary thrust struts and torque boxes
- Primary flight control surfaces: ailerons, elevators, and rudder
Warning
Exam Trap — Primary Control Surfaces : Under no circumstances can a primary flight control surface (aileron, elevator, rudder) or a primary structural member be missing under the CDL. An aircraft with a missing section of an elevator or a missing wing spar cap is legally unairworthy and cannot be dispatched under any CDL relief.
Secondary Structure (Eligible for CDL Deferral)
Secondary structure comprises components that provide aerodynamic fairing, environmental sealing, inspection access, or aerodynamic smoothing, but do not carry primary flight loads. Should a secondary aerodynamic component be missing, the primary load path remains fully intact, though localized aerodynamic drag and airflow disruption occur. CDL-eligible items include:
- Trailing edge flap track fairings (aerodynamic "canoes")
- Wing root and empennage fairing panels
- Engine cowling external access doors and pressure relief panels
- Landing gear door aerodynamic fairings and seal strips
- Wing slat track aerodynamic seals and rub strips
- Static discharge wicks on trailing edge surfaces
- Vortex generators on wings and vertical stabilizers
- MEL vs. CDL: Core Differences
Understanding the precise legal and operational differences between the MEL and CDL is essential for the practical flight dispatcher:
- Operational Feature Minimum Equipment List (MEL) Configuration Deviation List (CDL)
- Governing Regulation 14 CFR § 121.628 & OpSpec A050 14 CFR Part 25 (AFM Appendix) & § 121.173
- FAA Approving Authority Principal Operations Inspector (POI) / FSDO FAA Aircraft Certification Office (ACO)
- Physical Scope Inoperative instruments, systems, and avionics Missing external secondary airframe parts
Internal vs. External Primarily internal systems (hydraulics, electrics, packs) Exclusively external aerodynamic airframe surfaces
Repair Intervals Strict Categories (A, B, C, D) with calendar limits No lettered repair categories (Operate to next check)
Performance Penalties Occasional (e.g., altitude cap or pack-off drag) Standardized weight and fuel burn penalties
OpSpecs Extension Yes (M109/D095 grants 3 days for B, 10 days for C) Not Applicable (No calendar categories to extend)
Release Documentation Mandatory on Dispatch Release (§ 121.687) Mandatory on Dispatch Release (§ 121.687)
Important
The Absence of Repair Categories in the CDL : Unlike the MEL, the CDL does not have Category A, B, C, or D repair intervals . A missing flap track fairing canoe or access door deferred under the CDL does not expire after 3 or 10 days. The aircraft may be flown with the CDL item missing indefinitely—typically until the next scheduled maintenance C-check or until replacement parts arrive—provided all weight penalties, fuel burn penalties, and operational limitations are strictly observed on every flight dispatch release.
Types of CDL Penalties and Limitations
When a secondary airframe part is missing, the physical consequence is a disruption of smooth boundary-layer airflow, leading to increased parasite drag (form drag and interference drag) , localized airflow separation, and potential changes in aerodynamic buffet margins. To ensure compliance with Part 25 takeoff, en route, and landing climb requirements, the CDL prescribes specific performance penalties:
1. Weight Decrements (Takeoff, Landing & En Route)
The CDL specifies exact weight subtractions that must be applied to the structural or performance-limited gross weights of the aircraft:
Maximum Takeoff Weight (MTOW) Decrement : Subtracted from the field length limit, climb limit (second segment climb gradient under 14 CFR § 25.121), or obstacle clearance limit.
Maximum Landing Weight (MLW) Decrement : Subtracted from the approach climb limit or landing field length limit.
Maximum En Route Weight / Ceiling Decrement : Subtracted from the engine-inoperative drift-down ceiling calculation under 14 CFR § 121.191 over mountainous terrain.
2. Fuel Burn Penalties (Percentage En Route Bias)
Because parasite drag increases, the aircraft consumes more fuel per nautical mile at cruise. The CDL specifies a percentage fuel burn penalty (e.g., +1.5% or +2.0% ).
The aircraft dispatcher must manually enter this fuel burn bias into the flight planning computer or flight management system (FMS).
The percentage penalty applies to the planned en route burnoff . This indirectly increases required reserves, alternate fuel, and contingency fuel loads under 14 CFR § 121.639 .
3. Airspeed and Mach Limitations
Certain missing aerodynamic fairings expose underlying structures to severe aeroelastic flutter, buffet, or acoustic vibration at high transonic speeds. The CDL may impose reductions to the maximum operating limit speeds:
Reduction of Maximum Operating Limit Speed ( VMO ), e.g., from 340 KIAS down to 300 KIAS.
Reduction of Maximum Operating Mach Number ( MMO ), e.g., from Mach 0.82 down to Mach 0.78.
4. Maximum Operating Altitude Restrictions
Missing seals or fairings may degrade environmental control cooling airflow or aerodynamic stall margins at high angles of attack. The CDL may cap the maximum operating altitude (e.g., maximum cruise altitude restricted to FL 310 or FL 330).
Representative CDL Penalties for Transport Category Jet
Missing Component (CDL Item) Takeoff Weight Decrement (MTOW) Landing Weight Decrement (MLW) En Route Fuel Burn Penalty Operating Limitations
- Flap Track Fairing Canoe (Mid-Span) -1,200 lb -800 lb +1.5% None
- Air Conditioning Ram Air Deflector Door -350 lb -200 lb +0.8% VMO reduced to 310 KIAS
- Landing Gear Door Seal Strip -150 lb None +0.4% None
- Engine Cowling Pressure Relief Panel -500 lb -350 lb +1.0% Altitude capped at FL 350
- Trailing Edge Static Discharge Wicks (Up to 3) 0 lb 0 lb 0% Prohibited in RNP / Oceanic Airspace
- Rules for Combining Multiple CDL Items
In line operations, an aircraft may experience multiple missing secondary airframe parts simultaneously (e.g., a missing flap track fairing on the left wing and a missing ram air deflector door under the belly). The dispatcher must apply strict CDL combination rules:
1. The Cumulative / Additive Rule
Unless the AFM CDL preamble specifically provides a combined aerodynamic analysis table, all individual penalties are cumulative (additive) :
Total Weight Decrement = Sum of all individual weight decrements.
Total Fuel Burn Penalty = Sum of all individual percentage fuel burn penalties.
Practical Dispatcher Calculation Scenario
An aircraft is dispatched with two missing items listed in the AFM CDL:
Item 1: Flap Track Fairing Canoe #3 : Requires a 1,100 lb MTOW decrement , an 800 lb MLW decrement , and a +1.2% fuel burn penalty .
Item 2: Ram Air Deflector Door : Requires a 300 lb MTOW decrement , a 200 lb MLW decrement , and a +0.6% fuel burn penalty .
Runway Analysis : The maximum runway-limited takeoff weight for the departure runway is 172,500 lb.
Calculations :
- Total Takeoff Weight Decrement = 1,100 lb + 300 lb = 1,400 lb
- Adjusted Maximum Allowable Takeoff Weight = 172,500 lb - 1,400 lb = 171,100 lb
- Total Fuel Burn Penalty = 1.2% + 0.6% = +1.8%
If standard planned en route burn is 24,000 lb, the dispatcher must add 24,000 lb * 0.018 = 432 lb of additional trip fuel, plus appropriate alternate and reserve fuel buffer.
2. Symmetrical Restrictions (The Anti-Asymmetry Rule)
The CDL strictly prohibits certain symmetrical combinations. If an aerodynamic fairing is missing on the left wing, the corresponding fairing on the right wing cannot be missing simultaneously. Missing opposing symmetrical fairings causes asymmetric aerodynamic drag, resulting in continuous uncommanded roll or yaw moments that exceed autopilot trim authority or rudder control margins.
3. Same-Surface Restrictions
Generally, no more than one CDL item may be missing from the same individual control surface, flap assembly, or engine nacelle. If an inboard flap track canoe is missing, an aerodynamic rub strip on the same flap panel cannot be missing.
4. Maximum Total CDL Items
Most manufacturer CDL preambles specify that no more than three (or four) CDL items may be missing simultaneously from an aircraft without obtaining special engineering concurrence from the manufacturer and written authorization from the FAA ACO.
Flight Dispatcher Operational Control Workflow
Under 14 CFR § 121.687 , the aircraft dispatcher must ensure complete regulatory compliance before issuing the flight release:
Maintenance Log Verification : Confirm that the maintenance department has recorded the missing item in the aircraft maintenance logbook, verified that the item is secondary structure, and confirmed that remaining adjacent attachments are secure.
Runway Performance Recalculation : The dispatcher must enter the CDL weight decrements into the takeoff performance calculation software. The planned takeoff weight (PTOW) must not exceed the CDL-adjusted MTOW under any ambient temperature or runway condition.
Fuel Burn Bias Entry : The dispatcher must apply the cumulative CDL fuel penalty to the flight planning computer to ensure legal minimum fuel under 14 CFR § 121.639 .
Release Documentation : The dispatch release must explicitly list the CDL item number, description, weight decrement applied, and fuel penalty incorporated. Both the PIC and the dispatcher must sign or electronically acknowledge the release.