3.1 Structural and Induction Icing: Types, Accretion & Operations

FAA Aircraft Dispatcher Certificate ADX

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Regulations, Certification & Operational Control

1.1 Part 65 Subpart C: Certification, Eligibility & Currency 1.2 Operational Control & Dispatcher-PIC Joint Responsibility 1.3 Domestic, Flag & Supplemental Operations Framework 1.4 Dispatch Release Elements, Signatures & Recordkeeping 1.5 Regulations, Manuals, Crew Qualifications, and Source Control

2 Chapter 2: Atmospheric Physics, Pressure Systems & Fronts

2.1 Atmospheric Structure, Standard Atmosphere & Altimetry 2.2 Air Masses, Frontal Systems & Frontogenesis 2.3 Atmospheric Stability, Lapse Rates & Cloud Formation 2.4 Earth Motion, Regional Weather, Local Winds, and Water Phase Changes

3 Chapter 3: Aviation Weather Hazards & Severe Weather Avoidance

3.1 Structural and Induction Icing: Types, Accretion & Operations 3.2 Thunderstorms, Squall Lines, Microbursts & Low-Level Windshear 3.3 Clear Air Turbulence (CAT), Mountain Waves & Jet Streams 3.4 Low Ceilings, Fog Types & Visibility Restrictions 3.5 Hurricanes, Typhoons, Tornadoes, and Tropical Dispatch Hazards

4 Chapter 4: Weather Observations, Forecasts & Advisories Decoding

4.1 METAR and SPECI Surface Observations: Decoding & Operations 4.2 Terminal Aerodrome Forecasts (TAF): Groups & Timing 4.3 Pilot Weather Reports (PIREP): Coding, Severity & Urgent Alerts 4.4 In-Flight Advisories: AIRMETs, SIGMETs & Convective SIGMETs 4.5 Weather Collection, NWS Facilities, GFA, and EWINS

5 Chapter 5: Aviation Weather Charts & Upper-Air Analysis

5.1 Surface Analysis & Radar Summary Charts 5.2 Constant Pressure Analysis & Winds Aloft (FB) 5.3 Significant Weather Prognostic Charts (SIGWX) 5.4 Satellite Imagery, Moisture-Stability Analysis, and Forecast Integration

6 Chapter 6: Air Navigation, Airspace Architecture & Route Structure

6.1 National Airspace System: Classes, Rules & Special Use 6.2 Ground-Based Navigation Aids & Standard Service Volumes 6.3 Area Navigation (RNAV), GNSS/GPS, PBN & RNP Fundamentals 6.4 En Route Airways, SIDs, STARs & Chart Interpretation 6.5 Earth Coordinates, UTC, Chart Projections, and Flight Instruments 6.6 North Atlantic, Pacific, RVSM, and Global Navigation Differences

7 Chapter 7: Instrument Approaches, Minimums & Airport Operations

7.1 Precision Approach Systems: ILS Categories & Tolerances 7.2 Non-Precision Approaches, RNAV & Decision Minimums (MDA/DA) 7.3 Takeoff Minimums, Lower-Than-Standard & Takeoff Alternates 7.4 Holding Procedures: Patterns, Speed Limits & Timing

8 Chapter 8: Subsonic Aerodynamics & Jet Aircraft Performance

8.1 Subsonic Jet Aerodynamics: Lift, Drag & Flight Regimes 8.2 High-Altitude Flight: Mach Number, Buffet & Coffin Corner 8.3 Transport Turbine Engines: Thrust, Specific Fuel & Bleed Air

9 Chapter 9: Transport Category Takeoff & Landing Runway Analysis

9.1 Takeoff Performance Speeds & Balanced Field Concept 9.2 Takeoff Climb Segments & Obstacle Clearance Gradients 9.3 Landing Performance: Field Lengths, 60% Rule & Contamination

10 Chapter 10: En Route Performance, Driftdown Profiles & ETOPS Operations

10.1 One/Two-Engine-Inoperative En Route Net Profiles & Driftdown 10.2 Extended-Range Operations (ETOPS): Philosophy & Regulations 10.3 ETOPS En Route Alternates: Adequate vs. Suitable & Critical Fuel

11 Chapter 11: Aircraft Weight & Balance, Center of Gravity, and Loading

11.1 Transport Aircraft Structural Weight Limits: Definitions & Rules 11.2 Center of Gravity Computations: Datum, Arm, Moment & Index 11.3 Mean Aerodynamic Chord (%MAC) Computations & Stability 11.4 Payload-Range Analysis, Zero Fuel Weight Tradeoffs & Loading

12 Chapter 12: Destination Alternate Airport Selection & Weather Rules

12.1 Destination Alternate Selection: 91.169 & Part 121 1-2-3 Rule 12.2 Flag & Supplemental Operations Destination Alternate Rules 12.3 Derived Alternate Minimums: 1-Nav and 2-Nav Facility Rules

13 Chapter 13: Part 121 Fuel Planning, Reserves & En Route Re-Release

13.1 Part 121 Domestic Fuel Requirements: Reserves & Calculations 13.2 Part 121 Flag Fuel Requirements: 10% Reserve & Island Rules 13.3 Supplemental Fuel Requirements & Holding Fuel Management 13.4 Redispatch and En Route Re-release Procedures

14 Chapter 14: Transport Systems, Pressurization & MEL/CDL Procedures

14.1 Transport Jet Auxiliary Power, Electrical, Hydraulic & Pneumatic Systems 14.2 Cabin Pressurization, Rapid Decompression & Oxygen Requirements 14.3 Master Minimum Equipment List (MMEL), MEL & CDL Procedures 14.4 Flight Controls, Autoflight, Fuel, Oil, Brakes, and Fire Protection

15 Chapter 15: Hazardous Materials, Duty Regulations & Emergency Procedures

15.1 Dangerous Goods Carriage by Air (49 CFR Part 175) & NOTOC 15.2 Dispatcher Duty Limitations, Rest Requirements & Fatigue 15.3 Emergency Authority, Declaration & Diversion Decision-Making 15.4 NTSB Part 830 Accident Reporting & Wreckage Preservation 15.5 Security, Overdue Aircraft, and FAA Emergency Services

16 Chapter 16: Communications, ATC, and Flight Plan Procedures

16.1 Voice, Data Link, Position Reports, and Lost Communications 16.2 ATC Facilities, Separation, ICAO Flight Plans, and Traffic Management

17 Chapter 17: Human Factors and Practical Dispatch Applications

17.1 Dispatch Resource Management, Human Error, and Risk Decisions 17.2 Manual Flight Planning, PIC Briefing, Flight Watch, and Postflight Closeout

3.1 Structural and Induction Icing: Types, Accretion & Operations

Key Takeaways Explain This Topic AI

In-flight structural icing requires visible moisture and an airframe skin temperature at or below 0°C, with peak accretion between 0°C and -10°C.

Clear ice commonly forms from relatively large supercooled droplets; SLD can extend accretion aft of protected areas that flow back aft of heated zones before freezing, creating dense, disruptive horns that severely degrade lift.

Supercooled Large Droplets (freezing drizzle and freezing rain) exceed standard 14 CFR Part 25 Appendix C certification envelopes, threatening aileron hinge reversal and tailplane stalls.

Section 121.629 prohibits takeoff with the specified adhering contamination, subject to its narrowly authorized provisions and the approved ground program.

Holdover time is an estimated protection interval beginning with final fluid application; follow the approved program’s checks and alternatives, including its expired-time provisions.

Last updated: October 2026

3.1 Structural and Induction Icing: Types, Accretion & Operations

Quick Answer: Structural icing can form when supercooled liquid water contacts sufficiently cold aircraft surfaces. Visible moisture, temperature, droplet size, exposure, and aircraft protection all matter; the common temperature ranges are not absolute boundaries. Ground deicing and anti-icing follow § 121.629 and the carrier’s approved program, including its checks, fluids, holdover guidance, and permitted alternatives.

Atmospheric Physics of In-Flight Icing

Structural icing is one of the most insidious hazards in commercial air carrier operations. Water in the free atmosphere does not automatically freeze at 0 ∘ C 0^\circ\text{C} 0 ∘ C . In the absence of freezing nuclei, liquid water droplets can remain in a supercooled liquid state down to approximately − 40 ∘ C -40^\circ\text{C} − 4 0 ∘ C (the homogeneous nucleation threshold). When an aircraft collides with these supercooled water droplets (SWD), the mechanical impact triggers instantaneous or progressive freezing on the airframe.

Two fundamental conditions must exist simultaneously for in-flight structural icing:

Visible moisture — defined as clouds, fog with visibility of 1 statute mile or less, rain, freezing drizzle, or wet snow.

Freezing airframe skin temperature — indicated by an outside air temperature (OAT) or total air temperature (TAT) near or below 0 ∘ C 0^\circ\text{C} 0 ∘ C .

While structural icing has been recorded across temperatures ranging from + 2 ∘ C +2^\circ\text{C} + 2 ∘ C down to − 40 ∘ C -40^\circ\text{C} − 4 0 ∘ C in violent convective updrafts, the vast majority of severe structural icing encounters occur within the critical temperature band between 0 ∘ C 0^\circ\text{C} 0 ∘ C and − 10 ∘ C -10^\circ\text{C} − 1 0 ∘ C . Within this band, clouds contain the highest liquid water content (LWC) and the largest droplet diameters.

Static Air Temperature (SAT) vs. Total Air Temperature (TAT)

At transport jet cruise speeds, aerodynamic compression warms the airframe skin above the ambient free-stream temperature. This phenomenon is dynamic ram heating. Flight crews and dispatchers must distinguish between:

Static Air Temperature (SAT / OAT) : The actual ambient thermodynamic temperature of the undisturbed air mass.

Total Air Temperature (TAT) : The temperature measured by an onboard probe that brings the airflow to rest relative to the aircraft, capturing both ambient temperature and aerodynamic ram rise ( Δ T \Delta T Δ T ).

The ram temperature rise is approximated by: Δ T ≈ V 2 2 C p ≈ M 2 × T static 5 \Delta T \approx \frac{V^2}{2 C_p} \approx \frac{M^2 \times T_{\text{static}}}{5} Δ T ≈ 2 C p V 2 ≈ 5 M 2 × T static

Where M M M is Mach number and T static T_{\text{static}} T static is absolute temperature in Kelvin.

For an ideal perfect-gas, full-recovery illustration, total temperature is static absolute temperature multiplied by 1 + 0.2 M². At Mach 0.80 and −40 °C (233.15 K), this gives about 262.99 K, or −10.16 °C: a rise of approximately 29.84 °C. Actual indicated recovery and surface temperatures depend on the installation and conditions. Ram heating does not establish immunity from icing, and dispatchers must use the aircraft’s icing definitions, limitations, and procedures rather than a temperature shortcut.

Structural Ice Classifications: Clear, Rime, and Mixed

The physical structure, adherence, and aerodynamic hazard of ice accretion depend primarily on three variables: ambient temperature, droplet size, and liquid water content (LWC).

Feature Clear Ice (Glaze) Rime Ice Mixed Ice

Appearance Smooth, transparent, or glassy sheet Milky, opaque, granular, and rough Mottled, irregular, and heterogeneous

Droplet Size Large droplets ( > 50 μ m > 50\ \mu\text{m} > 50 μ m , SLD, rain) Small droplets ( < 20 μ m < 20\ \mu\text{m} < 20 μ m , stratus) Broad spectrum of droplet sizes

Temperature Band 0 ∘ C 0^\circ\text{C} 0 ∘ C to − 10 ∘ C -10^\circ\text{C} − 1 0 ∘ C − 10 ∘ C -10^\circ\text{C} − 1 0 ∘ C to − 20 ∘ C -20^\circ\text{C} − 2 0 ∘ C (and colder) − 8 ∘ C -8^\circ\text{C} − 8 ∘ C to − 15 ∘ C -15^\circ\text{C} − 1 5 ∘ C

Freezing Process Slow latent heat release; runback Instantaneous flash freezing; trapped air Simultaneous runback and flash freezing

Density & Adhesion High density ( 0.88 – 0.92 g/cm 3 0.88\text{--}0.92\text{ g/cm}^3 0.88 – 0.92 g/cm 3 ); very tenacious Low density ( 0.3 – 0.8 g/cm 3 0.3\text{--}0.8\text{ g/cm}^3 0.3 – 0.8 g/cm 3 ); brittle Moderate to high density; tenacious

Accretion Profile Double horns extending aft of boots Conforms closely to airfoil leading edge Asymmetric, jagged, severe roughness

Aerodynamic Threat Catastrophic drag rise, lift loss, runback Moderate lift loss, parasite drag rise High drag penalty, severe early stall

Clear Ice (Glaze Ice)

Clear ice forms when an aircraft penetrates clouds containing large supercooled droplets at temperatures near freezing ( 0 ∘ C 0^\circ\text{C} 0 ∘ C to − 10 ∘ C -10^\circ\text{C} − 1 0 ∘ C ). Because large droplets release substantial latent heat of fusion upon initial contact, only a small fraction of the droplet freezes instantaneously. The remaining liquid water flows rearward over the wing or cowl surface before completely freezing. This liquid runback produces a dense, solid, transparent sheet of ice with tremendous adhesion to the skin. Clear ice frequently builds up beyond the aft boundary of heated leading-edge slats or pneumatic de-icing boots, forming distinctive double horns that violently disrupt the boundary layer.

Rime Ice

Rime ice forms at colder temperatures (typically − 10 ∘ C -10^\circ\text{C} − 1 0 ∘ C to − 20 ∘ C -20^\circ\text{C} − 2 0 ∘ C or below) in clouds composed of small droplets, such as non-convective stratiform layers. Upon striking the airframe, the droplet freezes almost instantaneously. The rapid freezing traps microscopic air bubbles within the ice matrix, giving rime ice its characteristic milky, opaque appearance and brittle physical structure. Because there is no liquid runback, rime ice accumulates directly along the stagnation line of leading edges, largely conforming to the airfoil contour. Rime ice has lower density and weaker mechanical adhesion, making it significantly easier to break away with pneumatic de-icing boots.

Mixed Ice

Mixed ice occurs when cloud layers feature an unstable mixture of droplet sizes and transitional temperatures (typically − 8 ∘ C -8^\circ\text{C} − 8 ∘ C to − 15 ∘ C -15^\circ\text{C} − 1 5 ∘ C ). Drops freeze partially on impact while others run back, resulting in a rough, mushroom-shaped, irregular crust with high parasite drag penalties.

Supercooled Large Droplets (SLD) & Flight Control Hazards

Supercooled Large Droplets (SLD) are liquid water drops whose diameters exceed 50 μ m 50\ \mu\text{m} 50 μ m . They occur in the atmosphere as:

Freezing drizzle (FZDZ) : Droplet diameters between 100 μ m 100\ \mu\text{m} 100 μ m and 500 μ m 500\ \mu\text{m} 500 μ m ( 0.1 to 0.5 mm 0.1\text{ to } 0.5\text{ mm} 0.1 to 0.5 mm ).

Freezing rain (FZRA) : Droplet diameters exceeding 500 μ m 500\ \mu\text{m} 500 μ m ( > 0.5 mm > 0.5\text{ mm} > 0.5 mm ).

SLD formations develop either through the classical melting process (a warm inversion layer aloft melts falling snow into rain, which then falls into a sub-freezing surface layer) or through the collision-coalescence process in clouds with tops warmer than − 12 ∘ C -12^\circ\text{C} − 1 2 ∘ C . Melting Process Layer Profile:

Altitudes Aloft: Cold Layer (< 0°C) ---> Snowflakes Falling
Mid Altitudes: Warm Inversion (> 0°C) -> Snow Melts Completely into Raindrops
Near Surface: Sub-Freezing Layer (< 0°C) -> Rain Drops Supercool -> Freezing Rain (FZRA)
Aerodynamic Penalties

Ice accretion on lifting surfaces imposes severe performance penalties:

Drag increase : Parasite drag can increase by 100 % 100\% 100% to 200 % 200\% 200% , exceeding the available thrust of transport aircraft at high altitudes.

Lift reduction : Maximum lift coefficient ( C L , max ⁡ C_{L,\max} C L , m a x ) drops by 20 % 20\% 20% to 30 % 30\% 30% or more.

Stall speed surge : The stall speed ( V s V_s V s ) increases by 15 to 25 + knots 15\text{ to } 25+\text{ knots} 15 to 25 + knots , and the critical angle of attack ( α crit \alpha_{\text{crit}} α crit ) decreases significantly, sometimes inducing a stall without artificial stick shaker or pusher activation.

Aileron Hinge Reversal and Roll Upset

Because SLD droplets possess high kinetic energy, they do not follow air streamlines around the leading edge. Instead, they strike the wing and flow far aft before freezing, creating a spanwise ridge of ice aft of the protected de-icing or anti-icing zone. This ridge disrupts airflow over the ailerons, creating asymmetric airflow separation. The boundary layer separation induces an aerodynamic suction peak over one aileron, violently snapping the control surface upward. This phenomenon— aileron hinge moment reversal —can overwhelm the autopilot and the physical strength of the pilots, resulting in an immediate roll upset.

Ice-Contaminated Tailplane Stall (ICTS)

The horizontal stabilizer of a transport aircraft is an inverted airfoil producing negative lift (downward force) to counterbalance the nose-down pitching moment of the main wing and center of gravity. The horizontal stabilizer has a much thinner profile and sharper leading edge than the main wing, causing it to catch supercooled droplets at a rate 3 to 6 times higher than the wing.

When flaps are extended during approach, downwash over the tailplane increases dramatically, forcing the horizontal tail to operate at a significantly more negative angle of attack. If the tailplane leading edge is contaminated with ice, this increased negative angle of attack causes the lower surface of the tailplane to stall. When the tail stalls, downward aerodynamic force vanishes instantly, driving the aircraft into a violent, uncommanded pitch-down into terrain .

Caution

Tailplane Stall Recovery Trap: The recovery procedure for an Ice-Contaminated Tailplane Stall is the exact opposite of a conventional wing stall recovery! The flight crew must immediately retract flaps to the previous setting, pull back firmly on the control column, and reduce forward airspeed.

Engine Induction, Fan Blade, and Sensor Icing

Icing hazards extend beyond lifting surfaces into turbine engine induction and sensor systems:

Engine Cowl and Core Icing : Supercooled moisture striking engine nacelle lips, spinner cones, acoustic liners, and core compressor inlet guide vanes forms ice blocks. When these break off, the ingestion of ice chunks into the high-speed fan or core causes fan blade deformation, foreign object damage (FOD), severe engine vibration, compressor stalls, or total flameout. Engine anti-ice (EAI) utilizes hot engine bleed air routed through nacelle lips to maintain surface temperatures well above freezing.

Fan Blade Ice Shedding : During prolonged ground idle in freezing fog or freezing drizzle, ice accretes on the cold fan blades. Under Part 121 operations, standard operating procedures mandate periodic engine run-ups (e.g., accelerating to 50 % to 70 % N 1 50\%\text{ to } 70\%\ N_1 50% to 70% N 1 for 30 seconds every 10 to 30 minutes) to shed ice centrifugally before it unbalances the shaft.

Pitot-Static and Sensor Probe Icing : Pitot tubes, static ports, Total Air Temperature (TAT) probes, and Angle of Attack (AOA) vanes rely on internal electrical heating elements ( 115 V AC 115\text{V AC} 115 V AC ). If a pitot tube drain and ram hole become obstructed by ice, the airspeed indicator behaves like an altimeter: as the aircraft climbs, trapped pressure remains constant while ambient static pressure drops, causing indicated airspeed to falsely increase. If the crew responds by pulling the nose up to bleed off phantom airspeed, the aircraft can enter a catastrophic aerodynamic stall.

Ground De-Icing/Anti-Icing Fluids & The Clean Aircraft Concept
14 CFR 121.629 (Clean Aircraft Concept)

Federal regulations under 14 CFR 121.629 mandate the Clean Aircraft Concept : no person may dispatch, release, or take off an aircraft when frost, ice, or snow adheres to the wings, control surfaces, propellers, engine inlets, or other critical surfaces of the aircraft.

An exception exists in FAA-approved ground de-icing/anti-icing programs allowing takeoff with localized frost on the upper or lower fuel tank surfaces (cold-soak fuel frost) if within explicit manufacturer thickness limits (typically ≤ 1 / 8 inch \le 1/8\text{ inch} ≤ 1/8 inch on the lower wing surface caused by cold fuel remaining after high-altitude cruise).

SAE AMS Ground De-Icing and Anti-Icing Fluids

Ground fluids protect aircraft through chemical freezing point depressant technology, utilizing ethylene glycol or propylene glycol.

Fluid Category Color Viscosity Type Minimum Rotation Speed Primary Operational Use Typical Holdover Time (HOT)

Type I Red / Orange Unthickened (Newtonian); low viscosity None (any aircraft) De-icing: removes existing snow/ice; heated to 60 ∘ C– 80 ∘ C 60^\circ\text{C}\text{--}80^\circ\text{C} 6 0 ∘ C – 8 0 ∘ C Very short (3 to 15 minutes)

Type II Clear / Straw Thickened (pseudoplastic); polymeric ≥ 100 knots \ge 100\text{ knots} ≥ 100 knots Anti-icing: provides ground protection against falling precipitation Moderate (20 to 45+ minutes)

Type III Yellow / Amber Thickened (intermediate viscosity) < 100 knots < 100\text{ knots} < 100 knots (commuter/turboprop) Anti-icing for aircraft with low takeoff rotation speeds Intermediate (15 to 30 minutes)

Type IV Emerald Green Highly thickened (advanced pseudoplastic) ≥ 100 knots \ge 100\text{ knots} ≥ 100 knots Anti-icing: longest protection for heavy transport operations Extended (30 to 120+ minutes)

Holdover Time (HOT) Rules

Holdover Time (HOT) is defined as the estimated time that an anti-icing fluid will prevent the formation of frost, ice, or snow on the treated critical surfaces of an aircraft under prevailing ambient weather conditions.

Key regulatory and operational principles of HOT:

Clock Initiation : HOT begins precisely at the start of the final anti-icing application in a two-step process (or the start of the de-ice/anti-ice application in a single-step process). It does not begin when spraying stops or when the aircraft pushes back.

Pseudoplastic Shearing : Types II, III, and IV fluids are non-Newtonian pseudoplastic fluids. They cling to the wing while stationary or during slow taxi. When the aircraft accelerates along the runway, airflow creates boundary layer shear stress. At approximately 100 knots 100\text{ knots} 100 knots (or < 100 knots < 100\text{ knots} < 100 knots for Type III), the fluid shears thin and flows completely off the wing, leaving a clean aerodynamic surface for rotation.

HOT Expiration : When the published HOT range expires, the protection can no longer be guaranteed. Under Part 121:

A Pre-Takeoff Check is conducted within the HOT (typically from the flight deck, observing representative surfaces such as windshield wipers or wing leading edges).

A Pre-Takeoff Contamination Check is required if the HOT has expired or if weather conditions change to severe precipitation (e.g., heavy snow, freezing rain). This check must be conducted from inside the cabin or on the ground within 5 minutes prior to takeoff roll, inspecting critical surfaces to confirm they are completely free of contamination.

Operational Dispatcher Scenarios & Practical Traps Flight Dispatch Decision Matrix for Winter Operations:

1. Review TAF / METAR / PIREPs -> Identify FZRA, FZDZ, PL, or SN.

2. Evaluate En Route Airframe Penalties -> Factor 3% to 5% higher fuel burn for Thermal Anti-Ice.

3. Calculate Driftdown Profile -> Ensure engine-out gross ceiling clears icing cloud tops.

4. Confirm Departure Station Capabilities -> Verify Type IV availability & de-icing pad queue times.

5. Check 14 CFR 121.629 Compliance -> Ensure HOT covers taxi time; designate alternate if ground queue exceeds HOT.

Practical Dispatch Trap: The Driftdown Icing Trap

When planning a twin-engine transport jet flight over high terrain in freezing conditions, dispatchers compute one-engine-inoperative (OEI) net driftdown profiles under 14 CFR 121.191. If the aircraft suffers an engine failure in an area of active icing, wing and engine anti-ice systems must be activated using bleed air from the sole operating engine. This imposes two severe penalties:

Bleed air extraction reduces total available OEI thrust by up to 10 % 10\% 10% , lowering the aircraft's driftdown ceiling by 1,500 to 3,000 feet.

Residual ice accumulation on unheated surfaces increases drag, accelerating the rate of descent.

A dispatcher who calculates driftdown clearance assuming clean-wing aerodynamic performance will create an unrecoverable terrain collision risk if the flight encounters in-flight icing during driftdown.

Official References

Source check: 2026-10-12 . 2026 FAA Aviation Weather Handbook ; Icing operations § 121.629 . For operational use, apply current issued authorizations and the assigned aircraft’s approved data.