Study guide
6.1 National Airspace System: Classes, Rules & Special Use
FAA Aircraft Dispatcher Certificate ADX
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Regulations, Certification & Operational Control
1.1 Part 65 Subpart C: Certification, Eligibility & Currency 1.2 Operational Control & Dispatcher-PIC Joint Responsibility 1.3 Domestic, Flag & Supplemental Operations Framework 1.4 Dispatch Release Elements, Signatures & Recordkeeping 1.5 Regulations, Manuals, Crew Qualifications, and Source Control
2 Chapter 2: Atmospheric Physics, Pressure Systems & Fronts
2.1 Atmospheric Structure, Standard Atmosphere & Altimetry 2.2 Air Masses, Frontal Systems & Frontogenesis 2.3 Atmospheric Stability, Lapse Rates & Cloud Formation 2.4 Earth Motion, Regional Weather, Local Winds, and Water Phase Changes
3 Chapter 3: Aviation Weather Hazards & Severe Weather Avoidance
3.1 Structural and Induction Icing: Types, Accretion & Operations 3.2 Thunderstorms, Squall Lines, Microbursts & Low-Level Windshear 3.3 Clear Air Turbulence (CAT), Mountain Waves & Jet Streams 3.4 Low Ceilings, Fog Types & Visibility Restrictions 3.5 Hurricanes, Typhoons, Tornadoes, and Tropical Dispatch Hazards
4 Chapter 4: Weather Observations, Forecasts & Advisories Decoding
4.1 METAR and SPECI Surface Observations: Decoding & Operations 4.2 Terminal Aerodrome Forecasts (TAF): Groups & Timing 4.3 Pilot Weather Reports (PIREP): Coding, Severity & Urgent Alerts 4.4 In-Flight Advisories: AIRMETs, SIGMETs & Convective SIGMETs 4.5 Weather Collection, NWS Facilities, GFA, and EWINS
5 Chapter 5: Aviation Weather Charts & Upper-Air Analysis
5.1 Surface Analysis & Radar Summary Charts 5.2 Constant Pressure Analysis & Winds Aloft (FB) 5.3 Significant Weather Prognostic Charts (SIGWX) 5.4 Satellite Imagery, Moisture-Stability Analysis, and Forecast Integration
6 Chapter 6: Air Navigation, Airspace Architecture & Route Structure
6.1 National Airspace System: Classes, Rules & Special Use 6.2 Ground-Based Navigation Aids & Standard Service Volumes 6.3 Area Navigation (RNAV), GNSS/GPS, PBN & RNP Fundamentals 6.4 En Route Airways, SIDs, STARs & Chart Interpretation 6.5 Earth Coordinates, UTC, Chart Projections, and Flight Instruments 6.6 North Atlantic, Pacific, RVSM, and Global Navigation Differences
7 Chapter 7: Instrument Approaches, Minimums & Airport Operations
7.1 Precision Approach Systems: ILS Categories & Tolerances 7.2 Non-Precision Approaches, RNAV & Decision Minimums (MDA/DA) 7.3 Takeoff Minimums, Lower-Than-Standard & Takeoff Alternates 7.4 Holding Procedures: Patterns, Speed Limits & Timing
8 Chapter 8: Subsonic Aerodynamics & Jet Aircraft Performance
8.1 Subsonic Jet Aerodynamics: Lift, Drag & Flight Regimes 8.2 High-Altitude Flight: Mach Number, Buffet & Coffin Corner 8.3 Transport Turbine Engines: Thrust, Specific Fuel & Bleed Air
9 Chapter 9: Transport Category Takeoff & Landing Runway Analysis
9.1 Takeoff Performance Speeds & Balanced Field Concept 9.2 Takeoff Climb Segments & Obstacle Clearance Gradients 9.3 Landing Performance: Field Lengths, 60% Rule & Contamination
10 Chapter 10: En Route Performance, Driftdown Profiles & ETOPS Operations
10.1 One/Two-Engine-Inoperative En Route Net Profiles & Driftdown 10.2 Extended-Range Operations (ETOPS): Philosophy & Regulations 10.3 ETOPS En Route Alternates: Adequate vs. Suitable & Critical Fuel
11 Chapter 11: Aircraft Weight & Balance, Center of Gravity, and Loading
11.1 Transport Aircraft Structural Weight Limits: Definitions & Rules 11.2 Center of Gravity Computations: Datum, Arm, Moment & Index 11.3 Mean Aerodynamic Chord (%MAC) Computations & Stability 11.4 Payload-Range Analysis, Zero Fuel Weight Tradeoffs & Loading
12 Chapter 12: Destination Alternate Airport Selection & Weather Rules
12.1 Destination Alternate Selection: 91.169 & Part 121 1-2-3 Rule 12.2 Flag & Supplemental Operations Destination Alternate Rules 12.3 Derived Alternate Minimums: 1-Nav and 2-Nav Facility Rules
13 Chapter 13: Part 121 Fuel Planning, Reserves & En Route Re-Release
13.1 Part 121 Domestic Fuel Requirements: Reserves & Calculations 13.2 Part 121 Flag Fuel Requirements: 10% Reserve & Island Rules 13.3 Supplemental Fuel Requirements & Holding Fuel Management 13.4 Redispatch and En Route Re-release Procedures
14 Chapter 14: Transport Systems, Pressurization & MEL/CDL Procedures
14.1 Transport Jet Auxiliary Power, Electrical, Hydraulic & Pneumatic Systems 14.2 Cabin Pressurization, Rapid Decompression & Oxygen Requirements 14.3 Master Minimum Equipment List (MMEL), MEL & CDL Procedures 14.4 Flight Controls, Autoflight, Fuel, Oil, Brakes, and Fire Protection
15 Chapter 15: Hazardous Materials, Duty Regulations & Emergency Procedures
15.1 Dangerous Goods Carriage by Air (49 CFR Part 175) & NOTOC 15.2 Dispatcher Duty Limitations, Rest Requirements & Fatigue 15.3 Emergency Authority, Declaration & Diversion Decision-Making 15.4 NTSB Part 830 Accident Reporting & Wreckage Preservation 15.5 Security, Overdue Aircraft, and FAA Emergency Services
16 Chapter 16: Communications, ATC, and Flight Plan Procedures
16.1 Voice, Data Link, Position Reports, and Lost Communications 16.2 ATC Facilities, Separation, ICAO Flight Plans, and Traffic Management
17 Chapter 17: Human Factors and Practical Dispatch Applications
17.1 Dispatch Resource Management, Human Error, and Risk Decisions 17.2 Manual Flight Planning, PIC Briefing, Flight Watch, and Postflight Closeout
6.1 National Airspace System: Classes, Rules & Special Use
Key Takeaways Explain This Topic AI
Class A generally begins at 18,000 feet MSL through FL600; IFR rules and the standard pressure setting apply, with the actual regulatory airspace and exceptions checked.
Class B airspace covers terminal airspace around the nation's busiest hub airports, requiring an explicit ATC clearance to enter, Mode C and ADS-B Out within the 30 NM Mode C veil, and establishes a 250 kt speed limit below 10,000 ft MSL with a 200 kt speed limit beneath lateral shelves or inside VFR corridors (14 CFR 91.117).
Class C and Class D airspace require two-way radio communication prior to entry; Class C features an operational 5 NM core (surface to 4,000 ft AGL) and 10 NM shelf (1,200 ft to 4,000 ft AGL), with a maximum speed of 200 kt within 4 NM below 2,500 ft AGL.
Class E has several possible lower boundaries and also exists above FL600; VFR and IFR entry/equipment requirements differ.
Special Use Airspace (SUA) and Temporary Flight Restrictions (TFRs under 14 CFR 91.137/91.141/91.143) impose operational boundaries; dispatchers must ensure flight plans avoid active Restricted Areas, Prohibited Areas, and VIP/Space TFRs, recalculating en route fuel burn for required diversions.
Last updated: October 2026
6.1 National Airspace System: Classes, Rules & Special Use
Quick Summary: The United States National Airspace System (NAS) is classified into controlled (Classes A, B, C, D, and E) and uncontrolled (Class G) airspace under 14 CFR Part 71. For transport category air carriers operating under 14 CFR Part 121, joint operational control requires aircraft dispatchers to master airspace dimensions, pilot and aircraft equipment mandates, air traffic control (ATC) entry clearances, operating speed ceilings, and Special Use Airspace (SUA) boundaries. Tactical flight planning must actively account for Temporary Flight Restrictions (TFRs) and active military operations to prevent airborne deviations and ensure regulatory compliance.
1. Regulatory Architecture & 14 CFR Part 71 Framework
Title 14 of the Code of Federal Regulations (14 CFR) Part 71 establishes the legal designations and descriptions for all federal airways, controlled airspace, and reporting points within United States jurisdiction. The Federal Aviation Administration (FAA) classifies civil and military airspace into two overarching categories:
Controlled Airspace: Airspace of defined dimensions within which air traffic control service is provided to IFR flights and to VFR flights in accordance with the airspace classification. Controlled airspace comprises Classes A, B, C, D, and E.
Uncontrolled Airspace: Designated as Class G airspace, wherein ATC has neither the authority nor the regulatory obligation to provide separation services between operating aircraft.
For an aircraft dispatcher releasing a scheduled turbojet transport under 14 CFR Part 121, ordinary airline IFR operations use the applicable approved routes and terminal procedures; Part 121 also contains specifically applicable VFR provisions, and controlled-airspace status must not be assumed for every segment. Understanding the legal entry protocols, equipment mandates, and separation standards for each airspace class is essential for constructing viable dispatch releases and managing in-flight operational contingencies.
- 2. Controlled Airspace Classifications (Classes A, B, C, D, and E)
- Class A Airspace (FL180 to FL600)
Class A airspace represents the en route cruise environment for transport category jet aircraft:
Vertical Dimensions: Extends from 18,000 feet MSL (Flight Level 180 or FL180) up to and including Flight Level 600 (FL600) (60,000 feet pressure altitude).
Lateral Boundaries: Covers the contiguous 48 United States, Alaska, and coastal waters out to 12 nautical miles (NM) from the baseline of the United States coast.
Operating Rules (14 CFR 91.135): All aircraft operations in Class A airspace must be conducted under IFR on an ATC-approved IFR flight plan with an explicit ATC clearance. Visual Flight Rules (VFR) flight is strictly prohibited.
Pilot & Aircraft Equipment Mandates: The pilot in command must hold an instrument rating. The aircraft must be equipped with two-way radio communication equipment capable of continuous contact with ATC, an operable Mode C transponder with altitude reporting capability, and certified ADS-B Out avionics.
Altimeter Setting (14 CFR 91.121): Every aircraft climbing into or operating within Class A airspace must set its barometric altimeter subscale to standard atmospheric pressure: 29.92 inHg (1013.25 hPa) . This standard setting ensures identical vertical pressure datum separation among all aircraft regardless of local surface barometric variations.
Reduced Vertical Separation Minimum (RVSM): Between FL290 and FL410 inclusive, RVSM reduces vertical separation from the conventional 2,000 feet to 1,000 feet . Dispatchers must verify that the aircraft possesses certified RVSM equipment—dual independent primary altimetry systems, an altitude alerting system, an automatic altitude control system (autopilot), and an altitude-reporting transponder—and that the flight crew is RVSM-qualified under OpSpecs B046.
Class B Airspace (Major Hub Terminal Areas)
Class B airspace surrounds the nation's busiest passenger hub airports (such as ORD, ATL, DFW, LAX, and JFK) to protect high-density turbine air carrier operations:
Dimensions & Configuration: Class B is custom-tailored around each primary airport, typically resembling an "upside-down wedding cake." It extends vertically from the surface up to 10,000 feet MSL (certain locations with high terrain extend up to 11,000 or 12,500 feet MSL, such as DEN and SLC). The lateral structure comprises multiple concentric tiers:
Surface Core: Typically extends from the surface to 10,000 feet MSL within a 5 NM radius .
Intermediate Shelf: Often extends from 2,000 or 3,000 feet MSL up to 10,000 feet MSL between 5 and 10 NM .
Outer Shelf: Extends from 4,000 to 6,000 feet MSL up to 10,000 feet MSL out to 15, 20, or 30 NM .
Entry Requirements (14 CFR 91.131): An aircraft must receive an explicit ATC clearance prior to crossing the lateral boundary of Class B airspace (e.g., "Cleared into Class B airspace" ). Mere two-way communication or receiving radar vectors does NOT authorize penetration of Class B without the specific clearance phraseology.
Pilot Certification: Requires at least a Private Pilot certificate, or a Student Pilot with specific logbook training endorsements for that particular Class B airspace.
Equipment Mandates: Two-way radio communications, an operable VOR or TACAN receiver (for IFR operations), a 4096-code Mode C transponder, and ADS-B Out equipment.
The 30 NM Mode C Veil: Extending outward to a 30 NM radius from the primary Class B airport from the surface up to 10,000 feet MSL, all aircraft must operate an operable Mode C transponder and ADS-B Out, even when flying beneath the Class B lateral shelves in Class G or Class E airspace.
Class C Airspace (Regional Radar Approach Terminals)
Class C airspace protects busy regional airports served by scheduled air carriers with an operating control tower and radar approach control:
Dimensions & Configuration: Class C utilizes a standardized two-tiered cylindrical design centered on the primary airport:
Surface Area (Core): Extends from the surface up to 4,000 feet AGL above airport elevation within a 5 NM radius .
Shelf Area: Extends from 1,200 feet AGL up to 4,000 feet AGL between the 5 NM and 10 NM radius .
Outer Area: Extends to a 20 NM radius from the lower radar coverage floor up to the top of approach control airspace. Participation in the outer area is voluntary for VFR, but radar services are automatically provided.
Entry Requirements (14 CFR 91.130): The aircraft must establish two-way radio communication with the ATC facility providing Class C services prior to entry. Crucial operational rule: Two-way communication is legally established if ATC acknowledges the aircraft by using its specific callsign (e.g., "Delta 1024, standby" or "Skyhawk 734SP, squawk 4321" ). If the controller responds with "Aircraft calling standby" without using the callsign, communication is NOT established and the aircraft must remain outside Class C airspace.
Equipment Mandates: Operable two-way radio, Mode C transponder, and ADS-B Out equipment within and above Class C airspace up to 10,000 feet MSL.
Class D Airspace (Towered Non-Radar Terminals)
Class D airspace is established around smaller municipal or regional airports with an operating air traffic control tower that does not maintain full-time radar approach control:
Dimensions: Typically extends from the surface up to 2,500 feet AGL above the airport elevation, encompassing a tailored lateral radius of approximately 4 to 5 NM based on local instrument approach procedures.
Entry Requirements (14 CFR 91.129): Two-way radio communication must be established prior to entry (applying the identical callsign acknowledgment rule as Class C).
Part-Time Operations: Many Class D towers operate on part-time schedules. When the control tower closes, the airspace reverts to either a Class E surface area (if continuous weather observation and communication services exist) or Class G uncontrolled airspace . Dispatchers must consult the Chart Supplement (formerly A/FD) and current NOTAMs when releasing flights into part-time tower fields.
Class E Airspace (Controlled Airspace Continuum)
Class E airspace encompasses all controlled airspace not designated as Class A, B, C, or D. It provides ATC separation for IFR flights while allowing VFR flights to operate without an ATC clearance:
Vertical Tiers and Floor Levels:
Surface: Begins at the surface around non-towered airports with approved instrument approach procedures (depicted by a dashed magenta line on sectional charts).
700 feet AGL Transition Area: Begins at 700 feet AGL to protect aircraft executing instrument transition and approach procedures (depicted by the fuzzy edge of a magenta vignette).
1,200 feet AGL: Begins at 1,200 feet AGL across the vast majority of the contiguous United States (depicted by the fuzzy edge of a blue vignette, or serving as the default floor where no lower floor is charted).
14,500 feet MSL: In remote regions, Class E begins at 14,500 feet MSL up to, but not including, 18,000 feet MSL (FL180).
Above FL600: All airspace above Flight Level 600 is designated as Class E.
Federal Airways (Victor Routes): The protected airspace of federal Victor airways from 1,200 feet AGL up to, but not including, 18,000 feet MSL is Class E.
3. Uncontrolled Airspace: Class G Environment
Class G airspace extends from the surface up to the base of the overlying Class E controlled airspace (typically 700 feet AGL, 1,200 feet AGL, or 14,500 feet MSL):
ATC Authority: Air Traffic Control has neither the authority nor the equipment to provide separation services in Class G airspace. Flight safety relies entirely on see-and-avoid visual vigilance and pilot right-of-way rules.
Part 121 Operations in Class G: Under the applicable approved terminal-area procedures and and airline Operations Specifications (OpSpec C064), a scheduled air carrier may only operate into an uncontrolled airport in Class G airspace if:
The airport has an approved instrument approach procedure.
The carrier has an approved source of weather reporting (e.g., AWOS/ASOS or human observer).
The flight crew can maintain two-way communications with the company dispatch office or flight following facility.
The flight crew coordinates arrival traffic advisories on the local Common Traffic Advisory Frequency (CTAF) or UNICOM.
4. Airspace Speed Restrictions & Equipment Mandates (14 CFR 91.117 & 91.225)
Federal Aviation Regulation 14 CFR 91.117 establishes statutory airspeed ceilings across the National Airspace System to enhance pilot reaction time and collision avoidance:
Below 10,000 feet MSL (14 CFR 91.117(a)): No person may operate an aircraft below 10,000 feet MSL at an indicated airspeed of more than 250 knots .
Class C and Class D Corridors (14 CFR 91.117(b)): At or below 2,500 feet AGL within 4 nautical miles of the primary airport in Class C or Class D airspace, the maximum indicated airspeed is 200 knots .
Underlying Class B or VFR Corridors (14 CFR 91.117(c)): In the airspace underlying the lateral limits of Class B airspace, or within a designated VFR corridor through Class B airspace, the maximum indicated airspeed is 200 knots .
Minimum Safe Airspeed Exemption (14 CFR 91.117(d)): If the minimum safe airspeed for any particular operation (e.g., a heavily loaded Boeing 747 or 777 in clean climb configuration) is greater than the maximum speed prescribed in § 91.117, the aircraft may be operated at that minimum safe speed.
ADS-B Out Mandate (14 CFR 91.225)
Under federal regulations, automatic dependent surveillance-broadcast (ADS-B) Out equipment operating on 1090 MHz Extended Squitter is mandatory for all Part 121 operations in:
Class A, Class B, and Class C airspace.
Class E airspace at and above 10,000 feet MSL over the contiguous 48 states and D.C., excluding airspace at and below 2,500 feet AGL.
Within the 30 NM Class B Mode C veil from surface to 10,000 feet MSL.
Above the ceiling and within the lateral boundaries of Class B and Class C airspace up to 10,000 feet MSL.
In Class E airspace over the Gulf of Mexico at and above 3,000 feet MSL within 12 NM of the coast.
5. Comprehensive Airspace Architecture Comparison Table
Airspace Class Vertical Dimensions Entry Clearance / Radio Requirement Pilot Qualification Required Avionics Equipment Airspeed Limits (KIAS) ATC Separation Services Provided
Class A FL180 to FL600 Explicit ATC IFR Clearance Instrument Rated Two-way Radio, Mode C, ADS-B Out, RVSM (FL290-410) Mach / Speed assigned by ATC All aircraft (IFR only) separated
Class B Surface to 10,000 ft MSL (tailored) Explicit ATC Clearance ( "Cleared into Class B" ) Private Pilot or endorsed Student Two-way Radio, VOR/TACAN (IFR), Mode C, ADS-B Out 250 kt (< 10,000 ft), 200 kt (under shelf/corridor) All aircraft (IFR & VFR) separated
Class C Surface to 4,000 ft AGL (5 NM core / 10 NM shelf) Two-way Radio Communication (ATC uses callsign) Student Pilot Two-way Radio, Mode C, ADS-B Out 250 kt (< 10,000 ft), 200 kt (< 2,500 ft AGL within 4 NM) IFR from IFR, IFR from VFR; VFR traffic advisories
Class D Surface to 2,500 ft AGL (tailored 4-5 NM) Two-way Radio Communication (ATC uses callsign) Student Pilot Two-way Radio 200 kt (< 2,500 ft AGL within 4 NM) IFR from IFR; visual runway separation
Class E Surface, 700 ft, 1,200 ft, or 14,500 ft to FL180; > FL600 ATC Clearance for IFR; None for VFR Student Pilot (VFR), Instrument (IFR) IFR communication/navigation equipment; transponder and ADS-B as required by §§ 91.215/91.225, including applicable altitude/geographic exceptions 250 kt below 10,000 ft MSL IFR from IFR; no VFR separation
Class G Surface up to base of overlying Class E None (Uncontrolled) Student Pilot None (unless required by underlying corridor) 250 kt below 10,000 ft MSL None; see-and-avoid
6. Special Use Airspace (SUA) & Dispatch Planning
Special Use Airspace (SUA) consists of defined airspace within which specific flight activities must be confined or nonparticipating aircraft restricted for national defense, security, or hazardous operations:
Prohibited Areas (P): Airspace designated under 14 CFR Part 73 wherein the flight of aircraft is completely forbidden for national security or other welfare reasons (e.g., P-56 over Washington, D.C., protecting the White House and National Mall). Entry requires the authorization applicable to the prohibited area; do not plan ordinary unauthorized penetration.
Restricted Areas (R): Airspace denoting the existence of unusual, often invisible, hazards to aircraft such as artillery firing, aerial gunnery, or guided missiles. Penetration of Restricted Areas without authorization from the controlling agency is illegal when active. If a Restricted Area is active ("hot") , ATC will not route an IFR flight through it, and the dispatcher must plan the flight around its lateral boundaries. If inactive ("cold") , ATC may clear an IFR flight through the area without prior pilot or dispatcher coordination.
Warning Areas (W): Airspace extending from 3 nautical miles outward from the coast of the United States , containing activity hazardous to nonparticipating aircraft over domestic or international waters. Because Warning Areas reside over international airspace, the FAA cannot legally prohibit civil aircraft entry; however, dispatchers must treat them with equal caution and route around active operations.
Military Operations Areas (MOA): Airspace established to separate high-speed military training activities (aerobatics, air combat maneuvering, formation tactical flights) from IFR traffic. Nonparticipating IFR flights may be routed through an active MOA by ATC only if radar separation can be safely provided; otherwise, ATC issues a tactical reroute. VFR aircraft may enter an active MOA without clearance, though doing so carries extreme operational collision hazard.
Alert Areas (A): Airspace depicted on charts to inform nonparticipating pilots of high-density flight training activities or unusual aerial phenomena. All operations are permitted without ATC clearance, but flight crews and dispatchers should exercise heightened situational vigilance.
Controlled Firing Areas (CFA): Contain activities that, if not conducted in a controlled environment, could be hazardous to nonparticipating aircraft (ordnance disposal, industrial blasting). The unique operational distinction of CFAs is that activities must be suspended immediately whenever a ground spotter, radar, or lookout detects an approaching aircraft. Because CFAs do not force civil aircraft to alter their flight path, CFAs are NOT charted on any aeronautical chart.
7. Temporary Flight Restrictions (TFRs) & Dispatch Operational Impact
Temporary Flight Restrictions (TFRs) are regulatory tools issued by the FAA via Flight Data Center (FDC) NOTAMs under 14 CFR Part 91 to restrict flight through designated airspace:
14 CFR 91.137(a)(1): Protect persons and property on the surface or in the air from a hazard associated with an incident (e.g., toxic chemical spill, aircraft accident site, volcanic ash plume).
14 CFR 91.137(a)(2): Provide a safe operational environment for disaster relief aircraft operating in humanitarian emergencies (e.g., major forest fire aerial firefighting operations).
14 CFR 91.137(a)(3): Prevent an unsafe congestion of sightseeing aircraft over an incident or event which may generate high public interest.
14 CFR 91.141: Protect the President, Vice President, or other designated VIPs. Presidential TFRs typically feature an outer ring of 30 NM radius (limiting transit to discrete squawk codes and active ATC communications) and an inner core of 10 NM radius completely closed to all general aviation and commercial operations not specifically approved by the Secret Service and TSA.
14 CFR 91.143: Protect flight operations associated with space vehicles (e.g., Cape Canaveral Space Force Station, Kennedy Space Center, and Boca Chica Starbase launches). These TFRs extend from the surface to unlimited altitude across expansive maritime corridors.
14 CFR 91.145: Provides airshow/aerial-demonstration provisions. Stadium restrictions have a separate statutory/NOTAM basis. Read the actual current TFR coordinates, times, limits, and exceptions rather than attributing every stadium restriction to § 91.145.
Dispatch Operational Traps & Reroute Fuel Management
When a sudden VIP TFR or space launch restriction activates along a planned flight route, the dispatcher must evaluate the diversion path:
Fuel Burn Expansion: Diverting around a 30 NM Presidential ring or an extensive oceanic space launch corridor can add between 50 and 200 nautical miles to the total ground track. The dispatcher must recalculate the flight plan fuel burn under 14 CFR 121.639, adding contingency fuel to avoid en route minimum fuel declarations.
ATC Reroute Processing: If a flight is released on a route penetrating an active TFR, ATC will issue a tactical airborne reroute upon departure, often forcing lower cruising flight levels beneath overlying traffic flows, dramatically elevating turbojet specific fuel consumption.
Official References
Source check: 2026-10-12 . FAA AIM navigation guidance ; FAA aeronautical handbooks and current addenda ; Current AC 91-70 oceanic guidance . For operational use, apply current issued authorizations and the assigned aircraft’s approved data.