8.3 Transport Turbine Engines: Thrust, Specific Fuel & Bleed Air

FAA Aircraft Dispatcher Certificate ADX

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Regulations, Certification & Operational Control

1.1 Part 65 Subpart C: Certification, Eligibility & Currency 1.2 Operational Control & Dispatcher-PIC Joint Responsibility 1.3 Domestic, Flag & Supplemental Operations Framework 1.4 Dispatch Release Elements, Signatures & Recordkeeping 1.5 Regulations, Manuals, Crew Qualifications, and Source Control

2 Chapter 2: Atmospheric Physics, Pressure Systems & Fronts

2.1 Atmospheric Structure, Standard Atmosphere & Altimetry 2.2 Air Masses, Frontal Systems & Frontogenesis 2.3 Atmospheric Stability, Lapse Rates & Cloud Formation 2.4 Earth Motion, Regional Weather, Local Winds, and Water Phase Changes

3 Chapter 3: Aviation Weather Hazards & Severe Weather Avoidance

3.1 Structural and Induction Icing: Types, Accretion & Operations 3.2 Thunderstorms, Squall Lines, Microbursts & Low-Level Windshear 3.3 Clear Air Turbulence (CAT), Mountain Waves & Jet Streams 3.4 Low Ceilings, Fog Types & Visibility Restrictions 3.5 Hurricanes, Typhoons, Tornadoes, and Tropical Dispatch Hazards

4 Chapter 4: Weather Observations, Forecasts & Advisories Decoding

4.1 METAR and SPECI Surface Observations: Decoding & Operations 4.2 Terminal Aerodrome Forecasts (TAF): Groups & Timing 4.3 Pilot Weather Reports (PIREP): Coding, Severity & Urgent Alerts 4.4 In-Flight Advisories: AIRMETs, SIGMETs & Convective SIGMETs 4.5 Weather Collection, NWS Facilities, GFA, and EWINS

5 Chapter 5: Aviation Weather Charts & Upper-Air Analysis

5.1 Surface Analysis & Radar Summary Charts 5.2 Constant Pressure Analysis & Winds Aloft (FB) 5.3 Significant Weather Prognostic Charts (SIGWX) 5.4 Satellite Imagery, Moisture-Stability Analysis, and Forecast Integration

6 Chapter 6: Air Navigation, Airspace Architecture & Route Structure

6.1 National Airspace System: Classes, Rules & Special Use 6.2 Ground-Based Navigation Aids & Standard Service Volumes 6.3 Area Navigation (RNAV), GNSS/GPS, PBN & RNP Fundamentals 6.4 En Route Airways, SIDs, STARs & Chart Interpretation 6.5 Earth Coordinates, UTC, Chart Projections, and Flight Instruments 6.6 North Atlantic, Pacific, RVSM, and Global Navigation Differences

7 Chapter 7: Instrument Approaches, Minimums & Airport Operations

7.1 Precision Approach Systems: ILS Categories & Tolerances 7.2 Non-Precision Approaches, RNAV & Decision Minimums (MDA/DA) 7.3 Takeoff Minimums, Lower-Than-Standard & Takeoff Alternates 7.4 Holding Procedures: Patterns, Speed Limits & Timing

8 Chapter 8: Subsonic Aerodynamics & Jet Aircraft Performance

8.1 Subsonic Jet Aerodynamics: Lift, Drag & Flight Regimes 8.2 High-Altitude Flight: Mach Number, Buffet & Coffin Corner 8.3 Transport Turbine Engines: Thrust, Specific Fuel & Bleed Air

9 Chapter 9: Transport Category Takeoff & Landing Runway Analysis

9.1 Takeoff Performance Speeds & Balanced Field Concept 9.2 Takeoff Climb Segments & Obstacle Clearance Gradients 9.3 Landing Performance: Field Lengths, 60% Rule & Contamination

10 Chapter 10: En Route Performance, Driftdown Profiles & ETOPS Operations

10.1 One/Two-Engine-Inoperative En Route Net Profiles & Driftdown 10.2 Extended-Range Operations (ETOPS): Philosophy & Regulations 10.3 ETOPS En Route Alternates: Adequate vs. Suitable & Critical Fuel

11 Chapter 11: Aircraft Weight & Balance, Center of Gravity, and Loading

11.1 Transport Aircraft Structural Weight Limits: Definitions & Rules 11.2 Center of Gravity Computations: Datum, Arm, Moment & Index 11.3 Mean Aerodynamic Chord (%MAC) Computations & Stability 11.4 Payload-Range Analysis, Zero Fuel Weight Tradeoffs & Loading

12 Chapter 12: Destination Alternate Airport Selection & Weather Rules

12.1 Destination Alternate Selection: 91.169 & Part 121 1-2-3 Rule 12.2 Flag & Supplemental Operations Destination Alternate Rules 12.3 Derived Alternate Minimums: 1-Nav and 2-Nav Facility Rules

13 Chapter 13: Part 121 Fuel Planning, Reserves & En Route Re-Release

13.1 Part 121 Domestic Fuel Requirements: Reserves & Calculations 13.2 Part 121 Flag Fuel Requirements: 10% Reserve & Island Rules 13.3 Supplemental Fuel Requirements & Holding Fuel Management 13.4 Redispatch and En Route Re-release Procedures

14 Chapter 14: Transport Systems, Pressurization & MEL/CDL Procedures

14.1 Transport Jet Auxiliary Power, Electrical, Hydraulic & Pneumatic Systems 14.2 Cabin Pressurization, Rapid Decompression & Oxygen Requirements 14.3 Master Minimum Equipment List (MMEL), MEL & CDL Procedures 14.4 Flight Controls, Autoflight, Fuel, Oil, Brakes, and Fire Protection

15 Chapter 15: Hazardous Materials, Duty Regulations & Emergency Procedures

15.1 Dangerous Goods Carriage by Air (49 CFR Part 175) & NOTOC 15.2 Dispatcher Duty Limitations, Rest Requirements & Fatigue 15.3 Emergency Authority, Declaration & Diversion Decision-Making 15.4 NTSB Part 830 Accident Reporting & Wreckage Preservation 15.5 Security, Overdue Aircraft, and FAA Emergency Services

16 Chapter 16: Communications, ATC, and Flight Plan Procedures

16.1 Voice, Data Link, Position Reports, and Lost Communications 16.2 ATC Facilities, Separation, ICAO Flight Plans, and Traffic Management

17 Chapter 17: Human Factors and Practical Dispatch Applications

17.1 Dispatch Resource Management, Human Error, and Risk Decisions 17.2 Manual Flight Planning, PIC Briefing, Flight Watch, and Postflight Closeout

8.3 Transport Turbine Engines: Thrust, Specific Fuel & Bleed Air

Key Takeaways Explain This Topic AI

High-bypass turbofan engines operate on the continuous Brayton thermodynamic cycle, achieving superior propulsive efficiency ( η p = 2 1 + V j / V 0 \eta_p = \frac{2}{1 + V_j/V_0} η p ​ = 1 + V j ​ / V 0 ​ 2 ​ ) by accelerating large mass flows of cold bypass air at moderate exit velocities.

Engine Pressure Ratio (EPR) measures total pressure ratio across the engine ( P t 7 / P t 2 P_{t7}/P_{t2} P t 7 ​ / P t 2 ​ ), while N 1 N_1 N 1 ​ monitors low-pressure spool/fan speed; both serve as primary thrust-setting parameters subject to instrument icing vulnerability.

Transport turbofans are flat-rated to a corner point temperature (typically ISA + 15°C), delivering constant maximum thrust governed by internal structural/pressure limits below the corner, and rolling back above it due to Exhaust Gas Temperature (EGT) limits.

TSFC is fuel mass flow divided by thrust; its actual variation with altitude, Mach, thrust setting, and engine condition comes from approved aircraft data.

Bleed air extraction for air conditioning packs and engine/wing thermal anti-ice deprives the core of high-pressure working fluid, resulting in reduced available takeoff thrust, increased EGT, degraded climb gradients, and a aircraft- and configuration-specific increase in en route fuel burn.

Last updated: October 2026

Transport Turbine Engines: Thrust, Specific Fuel & Bleed Air

Quick Summary: Modern air carrier transports rely almost exclusively on high-bypass turbofan engines designed to deliver immense thrust, high thermodynamic efficiency, and exceptional operational reliability. For aircraft dispatchers, computing takeoff field lengths, obstacle clearance climb profiles, cruise fuel consumption, and drift-down terrain separation requires an intimate understanding of turbofan spool dynamics, flat-rated temperature limits, and the substantial performance penalties imposed by pneumatic bleed air extraction.

1. Thermodynamic Cycle: The Brayton Operating Cycle

Gas turbine engines operate on the continuous thermodynamic Brayton cycle (constant-pressure combustion cycle). Unlike reciprocating internal combustion engines that execute intermittent four-stroke cycles (Otto cycle: intake, compression, power, exhaust in batches), gas turbine engines perform all four thermodynamic processes simultaneously and continuously in separate specialized components:

Intake / Induction: Ambient air is captured by the engine nacelle inlet cowl, diffusing slightly to reduce velocity while raising static pressure before entering the compressor face.

Compression: Air passes through multiple rotating compressor rotor stages and stationary stator vanes, undergoing nearly isentropic compression. In modern high-pressure compressors, total pressure increases by overall pressure ratios (OPR) exceeding 40:1 to 50:1, raising air temperature to over 600 ∘ C 600^\circ\text{C} 60 0 ∘ C .

Combustion: In the annular combustion chamber, atomized Jet-A kerosene is sprayed into the airflow and ignited. Burning occurs at approximately constant static pressure, drastically elevating the gas stream's thermal energy and volume, producing temperatures exceeding 1,500 ∘ C 1{,}500^\circ\text{C} 1 , 50 0 ∘ C to 1,700 ∘ C 1{,}700^\circ\text{C} 1 , 70 0 ∘ C .

Expansion / Exhaust: The high-energy gas expands through turbine stages, extracting shaft work to drive the compressors and front fan. The remaining energetic gas expands through the exhaust nozzle at high velocity, generating reaction thrust according to Newton's third law.

2. High-Bypass Turbofan Architecture and Spool Mechanics

Modern transport aircraft utilize multi-spool high-bypass turbofans (such as the CFM LEAP, GE90/GE9X, Pratt & Whitney PW1000G Geared Turbofan, and Rolls-Royce Trent series).

Spool Dynamics: N 1 N_1 N 1 ​ vs. N 2 N_2 N 2 ​ (and N 3 N_3 N 3 ​ )

In a standard twin-spool turbofan:

Low-Pressure Spool ( N 1 N_1 N 1 ​ ): Consists of the large diameter front fan and intermediate low-pressure compressor (booster stages), driven via a concentric inner drive shaft by the multi-stage low-pressure turbine (LPT). N 1 N_1 N 1 ​ rotational speed is monitored on cockpit flight deck displays as a percentage of maximum rated RPM.

High-Pressure Spool ( N 2 N_2 N 2 ​ ): Consists of the high-pressure compressor (HPC), driven via an outer hollow shaft by the high-pressure turbine (HPT). The N 2 N_2 N 2 ​ spool operates at significantly higher rotational speeds than N 1 N_1 N 1 ​ and powers engine-mounted accessories (fuel pumps, oil pumps, integrated drive generators [IDGs], and hydraulic pumps). In Rolls-Royce three-spool engines, an intermediate spool ( N 2 N_2 N 2 ​ ) and high-pressure spool ( N 3 N_3 N 3 ​ ) provide additional aerodynamic optimization.

Bypass Ratio (BPR) and Propulsive Efficiency

The airflow entering the engine nacelle splits into two distinct paths:

Core Airflow ( m ˙ c o r e \dot{m}_{core} m ˙ core ​ ): Passes through the compressor, combustor, turbine, and core exhaust nozzle.

Bypass Airflow ( m ˙ f a n \dot{m}_{fan} m ˙ f an ​ ): Accelerated exclusively by the outer portion of the large front fan, ducting around the engine core and exiting through the fan discharge nozzle without ever entering the combustor.

The Bypass Ratio (BPR) is defined as: BPR = m ˙ f a n m ˙ c o r e \text{BPR} = \frac{\dot{m}_{fan}}{\dot{m}_{core}} BPR = m ˙ core ​ m ˙ f an ​ ​

While early first-generation turbojets had zero bypass ( BPR = 0 \text{BPR} = 0 BPR = 0 ) and early turbofans had ratios around 1:1 to 2:1, modern commercial airliners feature ultra-high bypass ratios ranging from 5:1 to over 11:1 (and up to 12.5:1 on modern geared architectures). In these engines, 80% to 90% of total takeoff thrust is generated by the cold bypass fan air , with only 10% to 20% produced by the hot core jet.

Why High Bypass Yields High Efficiency

Propulsive efficiency ( η p \eta_p η p ​ ) defines how effectively kinetic energy generated by the engine is converted into useful forward propulsive work: η p = 2 1 + V j V 0 \eta_p = \frac{2}{1 + \frac{V_j}{V_0}} η p ​ = 1 + V 0 ​ V j ​ ​ 2 ​

Where V j V_j V j ​ is the jet exhaust velocity and V 0 V_0 V 0 ​ is the aircraft flight speed.

Maximum propulsive efficiency occurs when exhaust velocity V j V_j V j ​ is as close as possible to the aircraft flight speed V 0 V_0 V 0 ​ .

Accelerating a small mass of air to extreme velocities (as in a pure turbojet) wastes massive kinetic energy in the turbulent exhaust wake ( Wasted Energy ∝ 1 2 m V j 2 \text{Wasted Energy} \propto \frac{1}{2} m V_j^2 Wasted Energy ∝ 2 1 ​ m V j 2 ​ ).

Accelerating a massive volume of air by a modest velocity increment (as in a high-bypass turbofan) produces the required total thrust ( F = m ˙ ( V j − V 0 ) F = \dot{m}(V_j - V_0) F = m ˙ ( V j ​ − V 0 ​ ) ) while maximizing propulsive efficiency and slashing fuel burn and noise emissions.

3. Thrust Measurement: Engine Pressure Ratio (EPR) vs. Fan Speed ( N 1 N_1 N 1 ​ )

Air carrier flight decks and dispatch release performance tables reference primary thrust parameters to set and verify rated engine power:

Engine Pressure Ratio (EPR)

Engine Pressure Ratio is the primary thrust-setting parameter utilized on many Pratt & Whitney and Rolls-Royce powerplants. EPR measures the ratio of total pressure at the turbine discharge to total pressure at the compressor inlet: EPR = P t 7 P t 2 (or P t 5 P t 2 ) \text{EPR} = \frac{P_{t7}}{P_{t2}} \quad \text{(or } \frac{P_{t5}}{P_{t2}} \text{)} EPR = P t 2 ​ P t 7 ​ ​ (or P t 2 ​ P t 5 ​ ​ )

Where:

P t 2 P_{t2} P t 2 ​ = Total pressure at the engine inlet face (sensed by the forward inlet pressure probe).

P t 7 P_{t7} P t 7 ​ (or P t 5 P_{t5} P t 5 ​ ) = Total pressure at the turbine exhaust nozzle.

An EPR of 1.00 indicates zero net pressure rise (engine idling or windmilling). Rated takeoff thrust typically commands EPR readings between 1.30 and 1.80 depending on atmospheric pressure and engine design.

Fan Speed ( N 1 N_1 N 1 ​ )

On General Electric, CFM International, and many modern electronic engine control (FADEC) platforms, N 1 N_1 N 1 ​ percentage serves as the primary thrust setting. Because the massive front fan acts as an advanced ducted propeller producing the vast majority of thrust, fan rotational speed directly correlates with mass airflow and thrust output across the flight envelope.

Parameter Engine Pressure Ratio (EPR) Fan Speed ( N 1 N_1 N 1 ​ )

Measurement Aerodynamic ratio of exhaust pressure to inlet pressure ( P t 7 / P t 2 P_{t7}/P_{t2} P t 7 ​ / P t 2 ​ ) Mechanical rotational speed of LP spool/fan as % of design limit

Typical Manufacturers Pratt & Whitney, Rolls-Royce General Electric, CFM International, IAE

Key Advantage Measures actual fluid work and pressure rise through the gas path Highly reliable physical sensor measurement unaffected by pressure ports

Primary Vulnerability Inlet probe icing ( P t 2 P_{t2} P t 2 ​ freeze) causes erroneously high EPR indications Does not directly measure hot core degradation or turbine blade wear

4. Thrust Variations with Atmospheric Conditions and Flat-Rating

The net thrust produced by a turbine engine is governed by the mass flow rate of air and the change in velocity: F n = m ˙ ( V j − V 0 ) F_n = \dot{m}(V_j - V_0) F n ​ = m ˙ ( V j ​ − V 0 ​ )

Because air density ( ρ \rho ρ ) is directly proportional to barometric pressure and inversely proportional to temperature ( P = ρ R T P = \rho R T P = ρRT ):

Altitude Effect: As an aircraft climbs, ambient pressure and density drop rapidly. Despite cold temperatures aloft, the loss of atmospheric density severely reduces the mass airflow ( m ˙ \dot{m} m ˙ ) entering the engine, causing maximum available thrust to decrease continuously with altitude. At FL350, available maximum thrust is typically only 20% to 25% of sea level rated thrust.

Airspeed Effect: Increasing flight airspeed creates two competing forces: ram pressure recovery (which increases compressor inlet pressure and mass flow) versus ram drag / momentum drag ( − m ˙ V 0 - \dot{m} V_0 − m ˙ V 0 ​ ). In the subsonic regime, net thrust initially decreases slightly as airspeed increases from zero, then levels off and recovers at high subsonic Mach numbers due to ram pressure compression in the intake cowl.

Ambient Temperature and Flat-Rating: Warmer air is less dense air, reducing mass airflow and available thrust. To protect internal components and provide predictable dispatch performance, transport engines are flat-rated .

Flat-Rated Engine Characteristics

Engines are engineered with structural capabilities that exceed their certified operating ratings. A flat-rated engine provides a constant maximum takeoff thrust from sub-zero temperatures up to a specified ambient temperature known as the corner point temperature (typically ISA + 15°C , or 30 ∘ C 30^\circ\text{C} 3 0 ∘ C at sea level):

Below the Corner Point (Structural / Pressure Limited): If the engine operated at full thermal capacity in dense, cold air, internal combustion pressures would exceed compressor case burst limits and over-torque the drive shafts. Full-authority digital engine controls (FADEC) throttle fuel flow to cap thrust at a constant flat-rated plateau.

Above the Corner Point (Exhaust Gas Temperature / Thermal Limited): As ambient temperature exceeds the corner point, air density is low. To achieve rated thrust, the engine would have to burn excess fuel, exceeding maximum allowable Turbine Inlet Temperature (TIT) and Exhaust Gas Temperature (EGT) limits, which would melt or degrade turbine blades. FADEC automatically rolls back available takeoff thrust along an EGT-limited slope.

5. Thrust Specific Fuel Consumption (TSFC)

The fuel efficiency of a jet engine is measured by its Thrust Specific Fuel Consumption (TSFC) : TSFC = m ˙ f u e l Thrust \text{TSFC} = \frac{\dot{m}_{fuel}}{\text{Thrust}} TSFC = Thrust m ˙ f u e l ​ ​

TSFC expresses the pounds of fuel consumed per hour per pound of thrust generated ( lb/hr lbf \frac{\text{lb/hr}}{\text{lbf}} lbf lb/hr ​ or kg/hr kN \frac{\text{kg/hr}}{\text{kN}} kN kg/hr ​ in metric units).

Lower TSFC values denote superior fuel efficiency.

Modern high-bypass turbofans achieve cruise TSFC values around 0.50 0.50 0.50 to 0.55 lb/(hr ⋅ lbf) 0.55 \text{ lb/(hr}\cdot\text{lbf)} 0.55 lb/(hr ⋅ lbf) , whereas early pure turbojets exceeded 0.90 0.90 0.90 .

Altitude Trend: TSFC improves (decreases) with altitude up to the tropopause. The cold ambient temperature aloft maximizes the thermodynamic thermal efficiency of the Brayton cycle:

The expression 1 minus cold/hot temperature describes a Carnot-limit comparison, not the ideal Brayton-cycle efficiency formula. Actual turbofan consumption depends on engine design, pressure ratio, temperature, thrust setting, and flight condition; use approved performance data.

Because cold ambient air acts as a more efficient heat sink, the engine burns significantly less fuel to produce a given amount of net thrust at high altitudes than at sea level.

6. Bleed Air Extraction and Dispatch Performance Penalties

Commercial transport jets rely on compressed air tapped from the engine compressor stages before fuel is introduced—a system known as engine bleed air .

Sources and Consumer Systems of Bleed Air

Bleed air is extracted from dedicated ports along the compressor casing:

Intermediate-Pressure (IP) Bleed: Tapped from lower stages (e.g., 5th or 7th stage) during high-power climb and cruise operations.

High-Pressure (HP) Bleed: Tapped from final stages (e.g., 9th or 10th stage) during low-power descent, approach, and ground idle when IP pressure is insufficient.

Key consumers of pneumatic bleed air include:

Environmental Control Systems (ECS): Air conditioning packs and cabin pressurization.

Thermal Anti-Ice Systems: Engine cowl anti-ice (EAI) and wing leading edge thermal anti-ice (WAI).

Ancillary Functions: Hydraulic reservoir pressurization, potable water tank pressurization, and cross-bleed engine starting.

Thermodynamic Cost of Bleed Extraction

Extracting compressed air represents a major thermodynamic loss:

The compressor consumed substantial shaft energy compressing that mass of air, but none of its potential expansion energy reaches the combustion chamber or turbine.

Less working fluid is available to produce thrust across the turbine nozzles.

To maintain target thrust, fuel flow must increase, driving EGT closer to redline limits.

If the engine is already operating at maximum thrust (such as during takeoff or maximum continuous climb), turning bleeds ON causes a direct reduction in available net thrust.

Operational Dispatch Penalties

Dispatchers must account for pneumatic configuration in computerized flight plans and takeoff performance calculations:

Takeoff Performance (Climb and Field Limits):

Operating with Engine Anti-Ice (EAI) ON reduces available takeoff thrust by roughly 1% to 2% per engine.

Operating with Wing Anti-Ice (WAI) ON draws massive quantities of hot bleed air, reducing takeoff thrust by up to 5% to 8%.

Reduced thrust degrades second-segment climb gradients and increases required takeoff runway distance. On runway-limited or obstacle-limited runways, dispatching with anti-ice ON forces a significant reduction in Maximum Allowable Takeoff Weight (MTOW).

APU-to-Pack Operations (No-Bleed Takeoff):

When departing hot-and-high airfields (e.g., Denver or Mexico City) near maximum gross weight, carriers utilize an APU-to-Pack takeoff procedure .

The Auxiliary Power Unit (APU) supplies pneumatic air to run the air conditioning packs during takeoff roll and initial climb.

The engine bleed valves are selected CLOSED, allowing 100% of engine compressor airflow to pass through the core, preserving full unpenalized engine takeoff thrust.

En Route Cruise Fuel Burn Adjustments:

Operating with engine anti-ice continuously ON in icing layers increases en route fuel flow by approximately 1.0% to 1.5% .

Operating with both engine and wing anti-ice active elevates cruise fuel burn by 2.0% to 4.0% .

Flight dispatchers must include contingency or icing fuel allowances in the dispatch release when en route icing forecasts dictate prolonged anti-ice operation.

• 7. Practical Traps & Operational Scenarios
• Practical Trap 1: The P t 2 P_{t2} P t 2 ​ Probe Icing Trap

During ground operations or climb in freezing fog or freezing drizzle, if the engine cowl anti-ice or probe heat is not activated, the forward P t 2 P_{t2} P t 2 ​ engine inlet pressure probe can become clogged with ice. Because ambient total pressure is trapped or restricted, the indicated P t 2 P_{t2} P t 2 ​ reads erroneously low. Since EPR = P t 7 / P t 2 \text{EPR} = P_{t7}/P_{t2} EPR = P t 7 ​ / P t 2 ​ , dividing by a falsely low denominator causes the cockpit EPR gauge to read significantly higher than actual thrust . A crew setting takeoff EPR based on this corrupt gauge will set dangerously low actual engine thrust, resulting in severe runway overrun hazards.

Practical Trap 2: Failure to Budget Bleed Air Penalties in Minimum Reserve Fuel

A flight dispatcher plans a flight through an active winter front with extensive stratiform clouds and moderate icing forecast between FL240 and FL310. The flight plan does not include an en route anti-ice fuel bias. The crew operates engine anti-ice and wing anti-ice for two hours en route. The unexpected 3.5% surge in fuel burn consumes all contingency fuel, resulting in an emergency low-fuel declaration upon arrival at the destination alternate.

Operational Scenario: Hot Day Corner Point Rollback at Phoenix Sky Harbor

On a summer afternoon at Phoenix (KPHX), ambient temperature reaches + 46 ∘ C +46^\circ\text{C} + 4 6 ∘ C (ISA + 31°C). Because the ambient temperature is well above the engine's flat-rated corner point of + 30 ∘ C +30^\circ\text{C} + 3 0 ∘ C (ISA + 15°C), the FADEC rolls back maximum available takeoff thrust to prevent exceeding EGT limits. The dispatcher cannot plan for standard flat-rated thrust; runway analysis confirms the flight is thrust-limited and must decrement maximum takeoff weight by 8,200 lbs or delay departure until evening cooling occurs.

Official References

Source check: 2026-10-12 . FAA Pilot’s Handbook of Aeronautical Knowledge ; Transport performance certification . For operational use, apply current issued authorizations and the assigned aircraft’s approved data.