Study guide

12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters

FAA Aviation Mechanic — Airframe AMA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Strategy

1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas

2 Chapter 2: Metallic Structures & Sheet Metal Repair

2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics

3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors

4 Chapter 4: Welding & Structural Fasteners

4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware

5 Chapter 5: Flight Controls, Assembly & Rigging

5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention

6 Chapter 6: Hydraulic & Pneumatic Power Systems

6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control

7 Chapter 7: Aircraft Landing Gear Systems

7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems

8 Chapter 8: Aircraft Fuel Systems

8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety

9 Chapter 9: Airframe Electrical Systems

9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting

10 Chapter 10: Cabin Atmosphere & Environmental Control

10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators

11 Chapter 11: Aircraft Instrument Systems

11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections

12 Chapter 12: Communication, Navigation & Warning Systems

12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning

13 Chapter 13: Ice, Rain & Fire Protection Systems

13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture

14 Chapter 14: Airframe Inspection & Maintenance Regulations

14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT

15 Chapter 15: Rotorcraft Fundamentals

15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

16 Chapter 16: Water & Waste Systems

16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety

12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters

Key Takeaways Explain This Topic AI

Air Traffic Control Transponders receive interrogations on 1030 MHz and reply on 1090 MHz, utilizing Mode A (4096 discrete 4-digit octal squawk codes), Mode C (100-foot increment pressure altitude via Gray/Gillham code), Mode S (24-bit unique ICAO aircraft address), and ADS-B Out broadcast links.

Standard international emergency squawk codes must be committed to memory: 7500 signifies hijacking/unlawful interference, 7600 signifies total loss of radio communications, and 7700 signifies an in-flight emergency or distress condition.

Under 14 CFR §91.413 and Part 43 Appendix F, aircraft ATC transponders must undergo comprehensive performance and calibration testing every 24 calendar months to verify frequency stability, receiver sensitivity, and altitude encoder correspondence within ±125 feet.

Emergency Locator Transmitters (ELTs) operating on 406.025 MHz digital frequencies transmit satellite distress beacons to Cospas-Sarsat, governed by 14 CFR §91.207 rules mandating battery replacement at 50% useful life or after 1 cumulative operating hour, and restricting operational testing to the first 5 minutes of any UTC hour for no more than 3 audio sweeps.

Last updated: August 2026

12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters

FAA Airframe Subject Matter Focus: Technicians must master the installation, testing, and regulatory maintenance requirements for Air Traffic Control (ATC) Radar Beacon System (ATCRBS) transponders, automatic altitude reporting digitizers, Mode S data links, ADS-B broadcast equipment, and Emergency Locator Transmitters (ELTs). Key FAA regulations include 14 CFR §91.413 (24-calendar-month transponder inspection), Part 43 Appendices E and F, and 14 CFR §91.207 (ELT operational rules, G-switch tests, and battery replacement intervals).

1. Air Traffic Control Transponder Systems (ATCRBS)

The ATC Transponder is an airborne secondary surveillance radar (SSR) transceiver that receives interrogations from ground ATC radar stations (or TCAS-equipped aircraft) and transmits an amplified, coded reply sequence. ATC TRANSPONDER RECEPTION & REPLY FREQUENCIES

  • [ Ground Secondary Radar ] ── 1030 MHz (Interrogation) ──> [ Aircraft ]
  • [ & TCAS Interrogators ] <── 1090 MHz (Coded Reply) ─── [ Transponder ]
  • Transponder Operating Modes

Transponder Mode Interrogation Spacing (P1 to P3) Reply Format & Capabilities

Mode A (Identity) 8.0 μ s 8.0\ \mu\text{s} 8.0 μ s spacing Transmits a 4-digit octal identification code (squawk code) ranging from 0000 to 7777 (4096 discrete combinations).

Mode C (Altitude) 21.0 μ s 21.0\ \mu\text{s} 21.0 μ s spacing Transmits automatic pressure altitude in 100-foot increments from standard sea-level datum (29.92 inHg / 1013.25 hPa) using Gillham/Gray code.

Mode S (Select) Interrogation on 1030 MHz with phase modulation Selective interrogation using a permanent, unique 24-bit ICAO aircraft address (over 16.7 million unique codes). Integrates TCAS II resolution advisories and data link communications.

ADS-B Out (14 CFR §91.225) Broadcasts automatically without interrogation Transmits GPS-derived position, altitude, and velocity via 1090 MHz Extended Squitter (1090ES) or 978 MHz Universal Access Transceiver (UAT) . MODE A / MODE C REPLY PULSE TRAIN STRUCTURE

  • F1 F2 SPI
  • ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐
  • │ │ │C1│ │A1│ │C2│ │A2│ │C4│ │A4│ │X │ │B1│ │ │ │ │
  • └──┘ └──┘ └──┘ └──┘ └──┘ └──┘ └──┘ └──┘ └──┘ └──┘ └──┘
  • │<───────────────────── 20.3 µs Total Framing ───────────────>│ │
  • 0.0 µs 20.3 µs 24.65 µs
  • Pulse Structure & Squawk Codes

Framing Pulses: Every transponder reply is bounded by two framing pulses, F1 and F2 , spaced exactly 20.3 μ s 20.3\ \mu\text{s} 20.3 μ s apart.

Information Pulses: Twelve information pulses ( A 1 , A 2 , A 4 , B 1 , B 2 , B 4 , C 1 , C 2 , C 4 , D 1 , D 2 , D 4 A_1, A_2, A_4, B_1, B_2, B_4, C_1, C_2, C_4, D_1, D_2, D_4 A 1 ​ , A 2 ​ , A 4 ​ , B 1 ​ , B 2 ​ , B 4 ​ , C 1 ​ , C 2 ​ , C 4 ​ , D 1 ​ , D 2 ​ , D 4 ​ ) are positioned at 1.45 μ s 1.45\ \mu\text{s} 1.45 μ s intervals between F1 and F2. Mode A codes use octal digits (0 to 7) because each digit is represented by three binary bits ( 1 + 2 + 4 = 7 1 + 2 + 4 = 7 1 + 2 + 4 = 7 ; digits 8 and 9 are impossible in octal).

SPI (Special Position Identification): Activated when the pilot presses the cockpit "IDENT" button. Adds a pulse 4.35 μ s 4.35\ \mu\text{s} 4.35 μ s after F2, causing the aircraft target to bloom/highlight on the controller's radar scope for approximately 18 seconds.

Critical Emergency Squawk Codes:

  • 7500: Hijacking / Unlawful Interference
  • 7600: Lost Radio Communications
  • 7700: In-Flight Emergency / Distress
  • 1200: Standard VFR flight in US airspace
  • 2. Altitude Encoders & 14 CFR §91.413 Inspection Requirements
  • Altitude Encoding Digitizers (Blind Encoders)

Mode C and Mode S transponders require continuous altitude inputs. This data is generated by an encoding altimeter or a solid-state blind altitude encoder plumbed directly into the aircraft static pressure system.

Standard Datum Reference: Encoders convert absolute static air pressure into standard pressure altitude referenced to 29.92 inches of mercury (1013.25 hPa) regardless of the local altimeter barometric setting. Ground ATC radar computers apply the local altimeter setting to correct the readout automatically.

Gillham (Gray) Code Bus: An 11-wire parallel data bus where only one binary bit changes state between adjacent 100-foot altitude steps. This single-bit transition prevents ambiguous binary readouts during pressure altitude changes.

Altitude Correlation Tolerance: Under 14 CFR Part 43 Appendix E, the pressure altitude reported by the transponder must correspond with the primary cockpit altimeter within ± 125 feet \pm 125\text{ feet} ± 125 feet at all tested altitudes. PITOT-STATIC & TRANSPONDER INTERFACE

  • [ Static Ports ] ─── Static Line ───┬───> [ Primary Cockpit Altimeter ]
  • │
  • └───> [ Blind Altitude Encoder ]
  • │ (Gillham / RS-232)
  • ▼
  • [ ATC Transponder ]
  • │ 1090 MHz
  • ▼
  • [ Bottom Blade Antenna ]
  • Transponder Certification & Testing (14 CFR §91.413)

Under 14 CFR §91.413 , no person may use an ATC transponder in controlled airspace unless, within the preceding 24 calendar months , the transponder has been tested, inspected, and found to comply with 14 CFR Part 43 Appendix F .

Part 43 Appendix F Test Parameters

Radio Frequency Tolerance: Reply carrier frequency must be 1090 ± 3 MHz 1090 \pm 3\text{ MHz} 1090 ± 3 MHz .

RF Peak Output Power: Minimum peak pulse power must be at least 70 Watts 70\text{ Watts} 70 Watts (for Class 2A/2B equipment on light aircraft below 15,000 ft) or 125 Watts 125\text{ Watts} 125 Watts (for Class 1A/1B equipment on aircraft operating above 15,000 ft or > 200 kts >200\text{ kts} > 200 kts ). Maximum power must not exceed 500 Watts 500\text{ Watts} 500 Watts ( + 27.0 dBW +27.0\text{ dBW} + 27.0 dBW ).

Receiver Sensitivity (MTL): Minimum Triggering Level (MTL) must be between − 73 dBm -73\text{ dBm} − 73 dBm and − 77 dBm -77\text{ dBm} − 77 dBm for ATCRBS transponders.

Side-Lobe Suppression (SLS): The transponder must reply to main-beam interrogation pulses (P1 and P3 equal amplitude) and must be suppressed (prevented from replying) when side-lobe pulses (P2 amplitude equal to or greater than P1) are received, preventing ghost targets.

3. Emergency Locator Transmitters (ELT)

An Emergency Locator Transmitter (ELT) is a self-contained, battery-powered emergency beacon designed to activate automatically during an aircraft crash deceleration to transmit homing distress signals to search and rescue (SAR) satellites and ground teams. COSPAS-SARSAT 406 MHz DIGITAL ELT SYSTEM

  • [ Crash Deceleration ] ──> [ Internal G-Switch Closes ]
  • │
  • ├─> 121.5 MHz Analog (Homing)
  • │
  • └─> 406.025 MHz Digital Burst (5W)
  • │ (24-Bit Hex ID + GPS)
  • ▼
  • [ LEOSAR / GEOSAR Satellites ]
  • │
  • ▼
  • [ Rescue Coordination Center ]
  • Analog (121.5 MHz) vs. Digital (406 MHz) ELTs
  • Parameter Legacy Analog ELT Modern Digital 406 MHz ELT (TSO-C126)
  • Primary Frequency 121.5 MHz (Civil) & 243.0 MHz (Military) 406.025 MHz / 406.028 MHz / 406.037 MHz

Satellite Monitoring Terminated by Cospas-Sarsat on Feb 1, 2009 Continuously monitored worldwide by geostationary (GEOSAR) and low-Earth orbit (LEOSAR) satellites.

Transmitter Power Low power (approx. 0.1 Watt / 100 mW ) High power ( 5 Watts pulse for 520 ms every 50 seconds).

Signal Format Downward-swept continuous audio tone (1600 Hz down to 300 Hz at 2–4 sweeps/sec). Digital data burst containing 24-bit aircraft hex ID, country code, owner contact, and encoded GPS position.

Position Accuracy Search area radius: 12 to 15 nautical miles Without GPS: 1 to 3 nautical miles ; With internal/external GPS: < 100 meters <100\text{ meters} < 100 meters .

Homing Signal Main carrier is the homing signal Transmits secondary low-power 121.5 MHz analog beacon for final tactical direction finding.

  • 4. ELT Installation, Inspection & Battery Maintenance (14 CFR §91.207)
  • Structural Mounting & G-Switch Inertia Sensor

Airframe Location: Under 14 CFR §91.207 and AC 43.13-2B, the ELT must be installed as far aft as practicable in the aircraft fuselage (typically in the empennage or baggage compartment forward of the vertical stabilizer), where structural crash damage is statistically least severe.

Longitudinal Orientation: The ELT must be mounted with its primary inertia switch ( G-switch ) sensitive axis aligned parallel to the longitudinal axis of the aircraft (pointing in the direction of forward flight).

Inertia Activation Threshold: Standard mechanical ball-and-spring or solid-state G-switches are calibrated to trigger automatically when subjected to a longitudinal deceleration force of 5.0 G ± 2 G 5.0\text{G} \pm 2\text{G} 5.0 G ± 2 G ( 2.3 to 7.0 G 2.3\text{ to } 7.0\text{G} 2.3 to 7.0 G ) with a duration of at least 11 milliseconds. 14 CFR §91.207 REGULATORY MANDATES

  • ┌─────────────────────────────────────────────────────────────────┐
  • │ 1. INSPECTION INTERVAL (14 CFR §91.207(d)): │
  • │ Inspected within 12 calendar months for: │
  • │ - Proper installation and structural mounting security │
  • │ - Battery corrosion and terminal integrity │
  • │ - Operation of controls and crash sensor (G-switch) │
  • │ - Radiated signal output using test receiver / dummy load │
  • ├─────────────────────────────────────────────────────────────────┤
  • │ 2. BATTERY REPLACEMENT CRITERIA (14 CFR §91.207(c)): │
  • │ Battery must be replaced (or recharged) when: │
  • │ - Transmitter in cumulative use for MORE THAN 1 HOUR │
  • │ - 50% of useful battery life (or storage life) has EXPIRED │
  • │ - New expiration date legibly marked on outside of case │
  • ├─────────────────────────────────────────────────────────────────┤
  • │ 3. OPERATIONAL TESTING RESTRICTIONS: │
  • │ - 121.5 MHz testing ONLY during FIRST 5 MINUTES of any hour │
  • │ - Radiated RF test limited to NO MORE THAN 3 AUDIO SWEEPS │
  • │ - 406 MHz digital test: use internal self-test mode ONLY │
  • └─────────────────────────────────────────────────────────────────┘
  • Operational Testing Rules per FAA AIM & AC 91-44A

Authorized Time Window: Live operational testing of an installed 121.5 MHz ELT using the cockpit remote switch must ONLY be conducted within the first 5 minutes past any UTC / clock hour (e.g., 10:00 to 10:05).

Audio Sweep Limit: Operational radiation must be restricted to no more than 3 audio sweeps (lasting approximately 1 to 2 seconds). Tests conducted outside this window or exceeding 3 sweeps can trigger airborne search and rescue false alarms.

406 MHz Self-Test: For 406 MHz ELTs, technicians must use the manufacturer's built-in self-test (BIST) sequence. The self-test transmits an inverted synchronization frame that is intentionally ignored by Cospas-Sarsat distress satellites.