Study guide
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics
FAA Aviation Mechanic — Airframe AMA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Strategy
1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas
2 Chapter 2: Metallic Structures & Sheet Metal Repair
2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs
3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics
3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors
4 Chapter 4: Welding & Structural Fasteners
4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
5 Chapter 5: Flight Controls, Assembly & Rigging
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention
6 Chapter 6: Hydraulic & Pneumatic Power Systems
6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control
7 Chapter 7: Aircraft Landing Gear Systems
7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems
8 Chapter 8: Aircraft Fuel Systems
8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety
9 Chapter 9: Airframe Electrical Systems
9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting
10 Chapter 10: Cabin Atmosphere & Environmental Control
10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators
11 Chapter 11: Aircraft Instrument Systems
11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections
12 Chapter 12: Communication, Navigation & Warning Systems
12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning
13 Chapter 13: Ice, Rain & Fire Protection Systems
13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture
14 Chapter 14: Airframe Inspection & Maintenance Regulations
14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT
15 Chapter 15: Rotorcraft Fundamentals
15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety
16 Chapter 16: Water & Waste Systems
16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics
Key Takeaways Explain This Topic AI
Primary flight controls govern the three aircraft axes: Ailerons control roll about the longitudinal axis, elevators/stabilators control pitch about the lateral axis, and the rudder controls yaw about the vertical (normal) axis.
Adverse yaw is caused by asymmetric induced drag produced when the down-going aileron increases wing camber and lift; it is aerodynamically mitigated using differential ailerons and Frise ailerons.
Secondary trim devices reduce pilot control forces: Ground-adjustable tabs are bent manually, cockpit-controllable tabs adjust cruise trim, balance tabs deflect opposite to control surface motion, servo tabs drive unpowered surfaces directly, and anti-servo tabs on stabilators deflect in the same direction to provide artificial feel and pitch stability.
Trailing-edge flaps increase lift coefficient ( C L C_L C L ) and drag: Plain, split, slotted (boundary-layer re-energizing), and Fowler flaps (which translate aft on tracks to increase wing chord area before hinging downward).
Aerodynamic balance devices (overhang balance, horn balance, and internal diaphragm balance seals) utilize airflow and differential pressure forward of the hinge line to reduce pilot stick forces.
Last updated: August 2026
Primary and Secondary Flight Control Surfaces & Aerodynamics
FAA Airframe Exam Focus: Flight control assembly and rigging requires an uncompromising understanding of how control surfaces generate aerodynamic moments around the three aircraft axes. Technicians must master the aerodynamic causes of adverse yaw, the mechanical design of differential and Frise ailerons, the operation and rigging of various trim tab types (especially anti-servo and spring tabs), and the function of trailing-edge flaps and aerodynamic balance seals.
1. Primary Flight Controls & The Three Aircraft Axes
Fixed-wing aircraft maneuver in three-dimensional space by rotating around three mutually perpendicular axes that intersect at the aircraft center of gravity (CG). Primary flight control surfaces produce aerodynamic lift or downforce, creating rotational moments around these axes. ▲ Vertical Axis (Yaw / Rudder)
- │
- │ ┌───┐
- │ ╔╪═══╪╗
- │ ║│ │║
- Longitudinal Axis │ ║│ │║ Lateral Axis (Pitch / Elevator)
- (Roll / Ailerons) ◄────┼────╫┼───┼╫────────────────────────────────►
- │ ║│ │║
- │ ║└───┘║
- │ ╚═════╝
- ▼
- Aircraft Axes of Motion & Primary Control Matrix
Axis Direction Motion Primary Control Surface Cockpit Control Input Inherent Stability
Longitudinal Nose to tail Roll (Banking) Ailerons (and roll spoilers) Yoke rotation / Stick lateral deflection Lateral Stability (Dihedral, sweepback)
Lateral Wingtip to wingtip Pitch (Nose up/down) Elevators , Stabilators , or Canards Yoke push/pull / Stick fore/aft Longitudinal Stability (CG vs Center of Lift, tail downforce)
Vertical (Normal) Top to bottom through CG Yaw (Nose left/right) Rudder Rudder pedals (left/right foot pressure) Directional Stability (Vertical stabilizer fin area)
Primary Control Surface Typologies & Empennage Configurations
Conventional Ailerons: Mounted on the outer trailing edges of wings, moving differentially (one up, one down). Deflecting the right aileron down increases right wing camber and lift, rolling the aircraft to the left.
Elevators: Hinged to the trailing edge of a fixed horizontal stabilizer. Moving the elevator up decreases tail lift, producing a downward tail aerodynamic force that pitches the nose upward.
All-Movable Stabilators: A single-piece horizontal tail surface pivoting on a central transverse torque tube or spindle. Because an all-movable stabilator lacks a fixed stabilizer leading edge, it provides extremely powerful pitch control but requires an anti-servo tab on its trailing edge to generate artificial dynamic control feel and prevent dangerous pilot-induced overcontrolling.
V-Tail (Ruddervators): Two slanted empennage surfaces forming a "V" that combine elevator and rudder functions. A mechanical or electromechanical mixing unit (ruddervator mixer) in the aft fuselage combines pitch yoke inputs and yaw pedal inputs:
Pitch Up Input: Both ruddervators deflect upward simultaneously.
Yaw Right Input: Right ruddervator deflects downward, left ruddervator deflects upward.
Elevons & Canards:
Elevons: Used on delta-wing and tailless aircraft (e.g., Concorde, fighters), combining aileron roll and elevator pitch functions through a mechanical mixer.
Canards: Horizontal stabilizing and control surfaces positioned forward of the main wing. Unlike conventional aft horizontal tails that generate negative downforce in cruise, canards generate positive lift, reducing total trim drag.
2. Adverse Yaw Mechanics & Corrective Aerodynamic Designs
When a pilot initiates a roll using ailerons, the aircraft naturally tends to yaw in the direction opposite the bank. This phenomenon is known as adverse yaw . ADVERSE YAW AERODYNAMICS:
- [ Down-Going Aileron (Left Wing) ] [ Up-Going Aileron (Right Wing) ]
- ──────────────────────────────── ────────────────────────────────
- Camber Increases • Camber Decreases
- Lift (L) Increases • Lift (L) Decreases
- Induced Drag (Di) INCREASES SHARPLY • Induced Drag (Di) DECREASES
Result: Higher induced drag on left wing pulls nose LEFT, opposing right roll!
The Aerodynamic Mechanism of Adverse Yaw
Induced drag is directly proportional to the square of the lift coefficient: D i = C L 2 π ⋅ e ⋅ A R ⋅ q ⋅ S D_i = \frac{C_L^2}{\pi \cdot e \cdot AR} \cdot q \cdot S D i = π ⋅ e ⋅ A R C L 2 ⋅ q ⋅ S
The wing with the down-going aileron experiences increased camber, shifting its local lift curve upward and producing a higher lift coefficient ( C L C_L C L ). This creates the desired roll upward, but simultaneously causes a substantial increase in induced drag ( D i D_i D i ) .
The wing with the up-going aileron experiences decreased camber, reducing its lift coefficient ( C L C_L C L ) and consequently reducing its induced drag ( D i D_i D i ).
The resulting net drag differential pulls the aircraft's nose toward the rising wing (away from the intended turn direction).
Engineering Solutions to Adverse Yaw
Aircraft manufacturers incorporate specific aerodynamic and mechanical designs to eliminate or counter adverse yaw: DIFFERENTIAL AILERONS: FRISE AILERONS:
Up-Going Aileron: Up-Going Aileron:
- Deflects 20° UP (High Form Drag) Leading edge projects BELOW wing bottom
- ┌─────────┐ ┌───────┐
- ─────────┘ └────── ──────────┤ └──────
- │ ◄── Protruding nose creates
Down-Going Aileron: │ profile / parasite drag!
Deflects 10° DOWN (Low Induced Drag) Down-Going Aileron:
- ─────────┐ ┌────── ──────────┴───────┘ (Smooth contour)
- └─────────┘
Differential Ailerons: The mechanical bellcrank and pushrod linkage is offset such that the up-going aileron travels upward through a significantly greater angular displacement (e.g., 20 ∘ to 25 ∘ 20^\circ\text{ to }25^\circ 2 0 ∘ to 2 5 ∘ UP) than the down-going aileron travels downward (e.g., 10 ∘ to 12 ∘ 10^\circ\text{ to }12^\circ 1 0 ∘ to 1 2 ∘ DOWN). The large upward deflection produces substantial parasite form drag on the down-going wing, balancing the induced drag generated by the up-going wing.
Frise Ailerons: The aileron hinge point is set back from the leading edge near the lower surface. When the aileron is deflected upward, its blunt, lower leading edge projects downward beneath the bottom wing skin , directly into the high-velocity airflow. This creates significant profile/form drag on the descending wing to counteract adverse yaw. When deflected downward, the leading edge remains smoothly tucked inside the wing contour.
Aileron-Rudder Interconnect: Mechanical spring cartridges or electronic mixer linkages automatically apply coordinated rudder displacement whenever ailerons are deflected, automatically yawing the nose into the turn.
3. Secondary & Auxiliary Flight Control Tabs
Secondary flight controls consist of trim tabs, spring tabs, balance tabs, and servo tabs mounted on the trailing edges of primary control surfaces. They reduce or eliminate steady-state pilot control stick forces and establish hands-off cruise trim. SUMMARY OF TRIM TAB TYPES & BEHAVIOR:
- [ Balance Tab ] [ Servo Tab ] [ Anti-Servo Tab ]
- (Reduces Pilot Force) (Flies the Main Surface) (Increases Feel / Stabilator Trim)
- Main Surface UP: ───▲ Pilot Input: Tab DOWN ───▼ Main Surface UP: ───▲
- Tab Moves: ───▼ Aerodynamic Force: Tab Moves: ───▲
- (Opposite Direction) Pushes Main Surface UP: ───▲ (Same Direction - Increases Load)
- Detailed Classification of Control Tabs
Tab Type Mechanical Linkage & Actuation Motion Relative to Main Surface Primary Aerodynamic Purpose Typical Aircraft Application
Fixed Ground-Adjustable Tab Non-movable sheet metal strip attached to trailing edge; bent manually on the ground. Stationary during flight. Corrects for persistent cruise roll/yaw trim tendencies at a specific design cruising airspeed. Light single-engine rudders and ailerons (e.g., Cessna 172 rudder).
Cockpit-Controllable Trim Tab Driven by cockpit handwheel, electric actuator, or trim jack-screw via cables/pushrods. Deflects opposite to desired control surface displacement. Trims out aerodynamic stick forces for varying airspeed, center of gravity, and power settings. Elevators and rudders across general aviation and transport aircraft.
Balance Tab Connected to a fixed stabilizer horn via a rigid mechanical link rod. Moves in OPPOSITE direction to the main control surface. Generates aerodynamic force assisting pilot input, reducing excessive control stick forces on large surfaces. High-speed aircraft elevators, ailerons, and rudders without hydraulic boost.
Servo Tab (Flight Tab) Connected directly to the cockpit flight controls; main control surface floats freely. Moves in OPPOSITE direction to primary surface. Pilot flies the small servo tab; tab aerodynamic lift physically deflects the heavy primary control surface. Large transport aircraft and unboosted airliners (e.g., Boeing 707/727 ailerons/elevators).
Anti-Servo Tab Mechanically linked to horizontal tail structure with fixed ratio link. Moves in the SAME direction as the stabilator trailing edge. Increases control stick resistance (artificial feel) to prevent pilot overstressing, and serves as pitch trim. All-movable stabilators (e.g., Piper Cherokee / Seminole series).
Spring Tab Incorporates a pre-loaded internal spring cartridge in the operating linkage. At low speeds, behaves like a rigid pushrod; at high speeds, spring compresses and tab acts as a servo tab . Provides light control forces at high indicated airspeeds where aerodynamic surface loads become excessive. High-speed multi-engine aircraft (e.g., Douglas DC-3/DC-6 rudder/elevator).
4. High-Lift & Drag Devices: Flaps, Slats, Slots & Spoilers
High-lift devices alter the camber and effective surface area of the wing to increase the maximum lift coefficient ( C L , max C_{L,\max} C L , m a x ), lowering stall speed ( V S 0 V_{S0} V S 0 ) and allowing steeper approach angles without increasing airspeed. WING FLAP TYPES:
- 1. Plain Flap 2. Split Flap
- ┌──────────────────┐ ┌──────────────────┐
- └────────────┬─────┘ └────────────┬─────┘
- │ ◄── Hinges Down └───┐ ◄── Lower skin deflects only
- 3. Slotted Flap 4. Fowler Flap
- ┌─────────────┐ ┌───┐ ┌─────────────┐
- └─────────────┘ │ │ └─────────────┘ ══════► ┌───┐ ◄── Moves AFT on tracks
- ▲ └───┘ └───┘ (Increases Area & Camber)
- └──── High-energy air slot
- Flap Architecture & Aerodynamic Comparison
Flap Design Mechanical Operation Δ C L , max \Delta C_{L,\max} Δ C L , m a x Increase Drag Characteristics Key Mechanical Features
Plain Flap Simple hinged trailing edge section deflects downward. + 50 % +50\% + 50% Moderate lift, high parasitic profile drag. Simple piano hinge; airflow separates from upper flap surface at modest deflection angles ( > 20 ∘ >20^\circ > 2 0 ∘ ).
Split Flap Lower wing skin deflects downward while upper surface remains flush. + 60 % +60\% + 60% High lift, very high parasitic drag. Creates massive low-pressure turbulent wake behind wing; excellent for steep, low-speed dive approaches.
Slotted Flap Hinge axis is offset below the wing, opening a duct or nozzle when deflected. + 90 % +90\% + 90% High lift, delayed boundary layer separation. Channels high-pressure air from lower surface to upper surface, energizing boundary layer and delaying stall.
Fowler Flap Moves aft on roller tracks and jackscrews before rotating downward. + 100 % +100\% + 100% to + 140 % +140\% + 140% Maximum lift increase with low initial drag (takeoff setting). Increases total wing surface area ( S S S ) and wing camber simultaneously. Standard on modern airliners.
Leading-Edge Devices & Lift Dumpers
Fixed Wing Slots: Built-in aerodynamic ducts near the leading edge that channel high-pressure air from under the wing onto the upper surface at high angles of attack (AoA), delaying wing stall.
Movable Slats: Leading-edge aerodynamic surfaces mounted on curved tracks. At high AoA, they extend forward and down either automatically (driven by aerodynamic pressure differential) or hydraulically/electrically, forming a slot that increases critical stall angle from 15 ∘ 15^\circ 1 5 ∘ to over 22 ∘ – 25 ∘ 22^\circ\text{--}25^\circ 2 2 ∘ – 2 5 ∘ .
Krueger Flaps: Hinged flaps that fold out from the lower leading edge of the wing to increase leading-edge camber, commonly used on inboard wing sections of jet transports.
Spoilers & Speed Brakes:
Flight Spoilers: Deploy differentially on the down-going wing in response to yoke inputs to assist aileron roll control.
Ground Spoilers (Lift Dumpers): Deploy fully upon main landing gear touchdown to destroy (dump) wing lift instantly, transferring aircraft weight entirely to wheels for maximum wheel brake friction and preventing bounce.
Speed Brakes: Aerodynamic drag panels extending from fuselage or wings to increase form drag without significantly altering lift.
5. Aerodynamic Balance Designs
Aerodynamic balancing reduces the pilot's physical workload by using aerodynamic forces to assist in deflecting primary control surfaces. AERODYNAMIC BALANCING METHODS:
- [ Horn Balance ] [ Overhang Balance ] [ Internal Seal Balance ]
- ┌──────┐ Hinge ┌───────────┐ Hinge ┌───────────┐ Flexible Seal
- ────┤ Horn │───┬─────── ────┤ Overhang ├──┬────── ────┤ ├───▓▓▓▓▓──┬──────
- ────┴──────┘ │ ────┴───────────┘ │ ────┤ Cavity ├───▓▓▓▓▓──┤
- ▼ ▼ └───────────┘ ▼
Horn Balance: A projecting portion of the control surface that extends forward of the hinge line at the wingtip or empennage tip. As the surface deflects, air strikes the horn forward of the hinge, producing an assisting aerodynamic moment.
Overhang Balance: The leading edge of the control surface extends forward of the hinge line inside a recessed pocket in the wing or stabilizer structure. Air flowing into the pocket exerts pressure on the overhang to help move the control.
Internal Balance Seals: A flexible elastomer/neoprene-coated fabric diaphragm spanning the gap between the wing spar and the control surface overhang inside a sealed chamber. Differential air pressure across the upper and lower wing vents acts across the diaphragm, exerting assisting pneumatic force on the control surface.