Study guide
6.1 Hydraulic Fluids, Seal Materials & Contamination Control
FAA Aviation Mechanic — Airframe AMA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Strategy
1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas
2 Chapter 2: Metallic Structures & Sheet Metal Repair
2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs
3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics
3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors
4 Chapter 4: Welding & Structural Fasteners
4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
5 Chapter 5: Flight Controls, Assembly & Rigging
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention
6 Chapter 6: Hydraulic & Pneumatic Power Systems
6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control
7 Chapter 7: Aircraft Landing Gear Systems
7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems
8 Chapter 8: Aircraft Fuel Systems
8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety
9 Chapter 9: Airframe Electrical Systems
9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting
10 Chapter 10: Cabin Atmosphere & Environmental Control
10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators
11 Chapter 11: Aircraft Instrument Systems
11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections
12 Chapter 12: Communication, Navigation & Warning Systems
12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning
13 Chapter 13: Ice, Rain & Fire Protection Systems
13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture
14 Chapter 14: Airframe Inspection & Maintenance Regulations
14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT
15 Chapter 15: Rotorcraft Fundamentals
15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety
16 Chapter 16: Water & Waste Systems
16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety
6.1 Hydraulic Fluids, Seal Materials & Contamination Control
Key Takeaways Explain This Topic AI
The three primary aircraft hydraulic fluid classes are vegetable-base (MIL-H-7644, dyed blue, natural rubber seals, alcohol flush), mineral-base (MIL-PRF-5606 / MIL-PRF-83282, dyed red, synthetic rubber/Buna-N seals, Stoddard solvent flush), and phosphate-ester base (Skydrol, dyed purple, butyl rubber/EPDM/Teflon seals, approved solvent/trichloroethane flush).
Intermixing incompatible hydraulic fluids causes severe chemical degradation, destroying elastomeric seals through extreme swelling, softening, or shrinkage, leading to rapid pressure loss and complete hydraulic failure.
O-rings provide bi-directional sealing and are sized by cross-section and inside diameter dash numbers per AS568; backup rings (MS28774 Teflon) must be installed on the low-pressure side away from pressure in systems exceeding 1,500 psi (two backup rings for double-acting actuators).
V-ring packings (chevron seals) are one-way pressure-energized seals that must always be installed with the apex of the 'V' pointing toward the source of fluid pressure so fluid forces the lips against sealing walls.
Fluid contamination is categorized into particulate, moisture, air, and chemical degradation; micronic filters rated at 5 to 10 microns with differential pressure indicators (PDI) maintain cleanliness, while entrained air causes pump cavitation and spongy flight controls.
Last updated: August 2026
6.1 Hydraulic Fluids, Seal Materials & Contamination Control
FAA Airframe Exam Focus: Aviation hydraulic power systems operate under extreme pressure regimes ranging from 1,000 psi in light aircraft to 3,000–5,000 psi in transport category and military jets. Airframe technicians must demonstrate mastery of hydraulic fluid chemistry, strict elastomer seal compatibility, mechanical packings, backup ring orientation, and fluid contamination prevention.
1. Physics of Hydraulic Power & Fluid Fundamentals
Hydraulic systems transmit force and motion through an incompressible confined fluid based upon Pascal's Principle : Pressure applied to any part of a confined liquid is transmitted equally and undiminished in all directions, acting with equal force on all equal areas and at right angles to them. Pressure ( P ) = Force ( F ) Area ( A ) ⟺ F = P × A \text{Pressure } (P) = \frac{\text{Force } (F)}{\text{Area } (A)} \quad \Longleftrightarrow \quad F = P \times A Pressure ( P ) = Area ( A ) Force ( F ) ⟺ F = P × A PASCAL'S LAW APPLIED
- Input Force: 100 lbs Output Force: 1,000 lbs
- │ ▲
- ▼ │
- ┌─────────────┐ ┌───────────────┐
- │ Input Piston│ │ Output Piston │
- │ Area: 1 in²│ │ Area: 10 in² │
- └───┬─────────┘ └───────┬───────┘
- │ System Pressure = 100 psi │
- └───────────────────────────────────────────────┘
- Essential Fluid Properties
To perform effectively in demanding aerospace environments, a hydraulic fluid must exhibit critical chemical and physical characteristics:
Incompressibility: Liquids compress negligibly under load (less than 0.5% per 1,000 psi), ensuring instantaneous mechanical transmission without lag.
Viscosity: The internal resistance of a fluid to flow. If viscosity is too high, internal fluid friction causes sluggish actuator response, high pressure drop, and excessive power draw. If viscosity is too low, fluid slips past internal clearances, increasing internal leakage and reducing pump volumetric efficiency.
Viscosity Index (VI): A measure of a fluid's change in viscosity relative to temperature change. Aviation hydraulic fluids require a high Viscosity Index so they remain fluid at sub-zero flight temperatures (-65°F / -54°C) while maintaining sufficient film strength and lubrication at high operating temperatures (+275°F / +135°C).
Chemical Stability & Oxidation Resistance: Fluids must resist polymerization, sludging, and acid formation when subjected to heat, shearing stress, and contact with airborne oxygen.
Flash Point, Fire Point & Auto-Ignition Point:
Flash Point: The temperature at which a liquid gives off sufficient vapor to ignite momentarily when an open flame is applied.
Fire Point: The temperature at which vapor continues to burn once ignited.
Auto-Ignition Point: The temperature at which vapors ignite spontaneously without an external ignition source.
Lubricating Power (Anti-Wear): The fluid acts as the sole lubricant for high-speed piston pumps, gear assemblies, and spool valves operating under extreme mechanical loading.
Demulsibility: The ability of fluid to separate rapidly and cleanly from water rather than forming emulsions.
2. The Three Primary Hydraulic Fluid Classes
Aircraft hydraulic fluids are categorized into three distinct chemical classes. Under no circumstances may different fluid types be intermixed , as their base chemistries and corresponding seal materials are entirely incompatible. ┌─────────────────────────────────────────────────────────────────────────────┐
- │ AIRCRAFT HYDRAULIC FLUID SPECTRUM │
- ├──────────────────────┬──────────────────────┬───────────────────────────────┤
- │ Vegetable-Base │ Mineral-Base │ Phosphate-Ester Base │
- │ MIL-H-7644 │ MIL-PRF-5606 / 83282 │ Skydrol 500B-4 / LD-4 / HyJet│
- ├──────────────────────┼──────────────────────┼───────────────────────────────┤
- │ • Castor oil/Alcohol │ • Petroleum Hydrocarb│ • Synthetic Phosphate Ester │
- │ • Dyed BLUE │ • Dyed RED │ • Dyed PURPLE / GREEN │
- │ • Natural Rubber │ • Buna-N / Nitrile │ • Butyl / EPDM / Teflon │
- │ • Alcohol Flush │ • Stoddard Flush │ • Approved Solvent Flush │
- │ • Flammable │ • Flammable (5606) │ • Fire-Resistant │
- └──────────────────────┴──────────────────────┴───────────────────────────────┘
- Comprehensive Hydraulic Fluid Comparison
Fluid Specification Chemical Base Characteristic Dye Color Compatible Seal Elastomers Flash Point Approved Flushing Solvent Typical Aircraft Applications
MIL-H-7644 Vegetable (Castor oil and ethyl alcohol blend) Blue Natural Rubber (MIL-R-6855 Class I) ≈ 300°F (149°C) Ethyl Alcohol or Denatured Alcohol Obsolete vintage aircraft; early tailwheel gear and brake systems.
MIL-PRF-5606 (formerly MIL-H-5606) Mineral / Petroleum (Refined petroleum hydrocarbon with VI improvers) Red Synthetic Rubber (Buna-N / Nitrile, Neoprene, Fluorocarbon / Viton) ≈ 200°F–225°F (93°C–107°C) Stoddard Solvent , Aliphatic Naphtha, Mineral Spirits General aviation, light twins, helicopters, military trainers, landing gear struts. Highly flammable petroleum oil.
MIL-PRF-83282 Synthetic Hydrocarbon (Polyalphaolefin / PAO base) Red Synthetic Rubber (Buna-N / Nitrile, Viton, Fluorosilicone) > 400°F (204°C) Stoddard Solvent , Naphtha Direct fire-resistant replacement for MIL-PRF-5606 in military and commercial rotorcraft/turboprops. Fully miscible with 5606.
Phosphate-Ester Base (Skydrol 500B-4, Skydrol LD-4, HyJet IV-A+, HyJet V) Synthetic Phosphate Ester Purple (Older Skydrol 7000 was dyed green; fresh fluid is clear purple) Butyl Rubber , Ethylene Propylene Diene Monomer ( EPDM ), Teflon (PTFE) > 350°F (177°C); Auto-ignition > 900°F (482°C) Trichloroethane , Isopropyl Alcohol, or Manufacturer-Approved Flushing Solvent Commercial transport category airliners (Boeing, Airbus), regional jets, business jets. Extreme fire resistance.
- Detailed Chemical Characteristics & Handling Rules
- 1. Mineral-Base Fluids (MIL-PRF-5606 & MIL-PRF-83282)
MIL-PRF-5606: Widely used in civil light aircraft and oleo strut shock absorbers. It is a petroleum oil dyed distinctively red to prevent confusing it with engine oil or fuel. However, its low flash point (≈ 200°F) presents a significant fire hazard if a high-pressure line atomizes fluid near hot brake rotors or exhaust stacks.
MIL-PRF-83282: Formulated with synthetic polyalphaolefin (PAO) to mitigate the flammability of 5606. It features a flash point exceeding 400°F and an auto-ignition temperature above 750°F. It is completely miscible and compatible with MIL-PRF-5606 and uses identical synthetic rubber (Buna-N) seals.
2. Phosphate-Ester Base Fluids (Skydrol & HyJet)
Fire Resistance: Phosphate-ester fluids were engineered to eliminate catastrophic in-flight hydraulic fires in high-performance turbine aircraft. When sprayed across a 1,200°F hot manifold, Skydrol will not propagate a flame.
Corrosive & Paint Stripping Effects: Phosphate esters are powerful plasticizers and solvents. Skydrol will rapidly soften and strip standard aircraft paints, alkyd enamels, and lacquers. Aircraft compartments exposed to phosphate-ester hydraulic systems must be coated with epoxy or polyurethane primers and finishes .
Plastics & Wire Insulation Incompatibility: Phosphate esters attack vinyl, PVC, acrylics (plexiglass windshields), and polystyrene. Wiring in hydraulic bays must use Teflon (PTFE), Kapton, or Tefzel insulation.
Health Hazards & PPE: Phosphate-ester fluid is an active irritant. Contact with exposed skin causes a persistent, painful chemical stinging and erythema. Contact with the eyes causes severe burning pain. Maintenance personnel must wear chemical-resistant butyl rubber gloves , splash goggles, and face shields. If contact occurs with the eyes, flush immediately with copious fresh water and seek medical attention; for skin contact, wash thoroughly with soap and water.
Warning
Never use Stoddard solvent, mineral spirits, or petroleum cleaning agents to clean or flush a phosphate-ester (Skydrol) hydraulic system. Petroleum solvents will attack and degrade the butyl rubber and EPDM seals, resulting in rapid seal swelling, softening, and catastrophic hydraulic failure. Only use approved solvents such as trichloroethane, isopropyl alcohol, or the manufacturer's designated flushing fluid.
3. Fluid Incompatibility & Decontamination Protocols
Intermixing different classes of hydraulic fluids is one of the most dangerous maintenance errors in aviation. The base oil of one fluid class acts as a destructive chemical solvent against the elastomer seals formulated for another class. FLUID / SEAL COMPATIBILITY MATRIX
- ┌────────────────────────────────────────┐
- │ FLUID CLASS │
- ├──────────────┬─────────────┬───────────┤
- │ Vegetable │ Mineral │ Phosphate │
- ┌────────────────────┼──────────────┼─────────────┼───────────┤
- │ Natural Rubber │ COMPATIBLE │ Swells │ Destroys │
- │ Buna-N / Nitrile │ Softens │ COMPATIBLE │ Destroys │
- │ Butyl / EPDM │ Degrades │ Swells │ COMPATIBLE│
- │ Teflon (PTFE) │ COMPATIBLE │ COMPATIBLE │ COMPATIBLE│
- └────────────────────┴──────────────┴─────────────┴───────────┘
- Consequences of Inadvertent Fluid Cross-Contamination
Seal Swelling: Incompatible fluid absorbs into the polymer matrix of the O-ring or packing, causing it to swell by 20%–80%. The swollen seal binds inside the actuator or valve bore, causing valve spool seizure, severe control surface stiffness, or jammed actuators.
Seal Softening & Gummy Degradation: The elastomer loses mechanical shear strength, breaks apart into gummy particulate debris, and sludges internal flow orifices and check valves.
Seal Shrinkage & Hardening: The chemical base leaches out the elastomer's plasticizers, turning seals brittle and causing severe high-pressure fluid blow-by.
Comprehensive Decontamination and Flushing Procedure
If an aircraft hydraulic system is inadvertently contaminated with the wrong fluid type:
Do not operate the hydraulic pumps or cycle flight controls. Operating the system drives contaminated fluid throughout all actuators, valves, accumulators, and lines.
Defuel and drain: Open all low-point drain valves and completely drain the reservoir, lines, and accumulators.
Component tear-down: Disassemble all hydraulic units (pumps, selector valves, actuators, accumulators). Every single elastomeric seal, O-ring, backup ring, and wiper must be removed, discarded, and replaced with the correct elastomer.
System flushing: Flush all lines and metal components with the approved flushing solvent for the intended fluid class (e.g., anhydrous alcohol for vegetable-base, Stoddard solvent for mineral-base, trichloroethane for phosphate-ester).
Refill and Bleed: Reassemble components with fresh seals, refill the reservoir with the correct certified fluid specification, connect an external hydraulic mule, and thoroughly bleed all air and residual solvent from every sub-circuit.
4. Hydraulic Packings, Seals, and Backup Rings
Hydraulic seals are mechanical devices designed to prevent internal and external fluid leakage and exclude foreign contaminants. Seals are divided into two fundamental operational classes:
Static Seals (Gaskets): Used between two stationary surfaces (e.g., reservoir end caps, valve body plugs, line fittings).
Dynamic Seals (Packings): Used between surfaces experiencing relative motion (e.g., sliding actuator piston rods, rotating pump shafts, oscillating valve spools). O-RING CROSS-SECTION & GLAND
- ┌──────────────────────────────────────┐
- │ Cylinder Wall │
- ├──────────────────────────────────────┤
- │ ▲ Pressure │
- │ │ │
- │ ┌────┴────┐ ┌───────────┐ │
- │ │ │ │ Backup │ │ ◄── Low-Pressure
- │ │ O-Ring │ │ Ring │ │ Side
- │ │ │ │ (Teflon) │ │
- │ └────┬────┘ └───────────┘ │
- ├────────────┼─────────────────────────┤
- │ ▼ Extrusion Gap │
- │ Actuator Piston │
- └──────────────────────────────────────┘
- 1. O-Ring Packings (MS28775 / AS568 / NAS1613)
An O-ring is a one-piece molded elastomeric ring with a circular cross-section. It seals bi-directionally. When fluid pressure is applied, the O-ring is forced against the opposite side of its retaining groove (gland), squeezing the elastomer against both the cylinder wall and the groove base to create a positive barrier.
Dash Numbering System: Standard aerospace O-rings use the Aerospace Standard ( AS568 ) dash numbering system. The dash number designates both the nominal cross-sectional diameter (width) and the inside diameter (ID). For example, -001 through -099 represent standard 1/16 in cross-sections, -100 series represent 3/32 in, -200 series represent 1/8 in, and -300 series represent 3/16 in.
Elastomer Identification & Dot Coding: Preformed packings are marked with color dots, stripes, or manufacturer tags:
Blue Dot / Stripe: Compatible with MIL-PRF-5606 mineral-base fluid.
Green Dot / White Stripe: Compatible with synthetic hydrocarbon fluids.
Solid Green / Purple Marking: Compatible with phosphate-ester fluids (Skydrol / HyJet).
Cure Dates & Shelf Life (MIL-HDBK-695): Elastomers degrade over time due to atmospheric ozone, UV light, and temperature. O-ring cure dates are expressed in quarters and years (e.g., 2Q26 = 2nd quarter of 2026). Seals exceeding authorized shelf-life limits (typically 3 to 5 years for standard nitrile; extended or unlimited for fluoroelastomers/Teflon) must be discarded.
2. Backup Rings (MS28774 Teflon / MS27595 / Spiral & Scarf-Cut)
When system operating pressures exceed 1,500 psi , hydraulic pressure can force the soft rubber O-ring into the microscopic clearance gap between the moving piston and cylinder bore—a destructive failure known as seal extrusion or 'nibbling'. BACKUP RING INSTALLATION RULES
- SINGLE-ACTING CYLINDER DOUBLE-ACTING CYLINDER
- (Pressure from Left Only) (Pressure from Both Sides)
- Pressure ──► ◄── Pressure ──►
- ┌───────────────────────┐ ┌────────────────────────┐
- │ ┌───────┐ ┌─────────┐ │ │ ┌───────┐┌─────┐┌─────┐│
- │ │ O-Ring│ │ Backup │ │ │ │Backup ││O-Rng││Back ││
- │ │ │ │ Ring │ │ │ │ Ring ││ ││Ring ││
- │ └───────┘ └─────────┘ │ │ └───────┘└─────┘└─────┘│
- └───────────────────────┘ └────────────────────────┘
- Backup placed on Backup placed on
- LOW-PRESSURE side BOTH sides of O-Ring
Strict Backup Ring Rules:
Material: Modern backup rings are manufactured from Teflon (PTFE) , which offers high shear strength, extreme chemical inertness, and a low coefficient of friction.
Single-Acting Actuators: A single backup ring is installed on the low-pressure side of the O-ring (the side away from the pressure source), shielding the elastomer from the extrusion gap.
Double-Acting Actuators: When fluid pressure is applied alternately to both sides of the piston, two backup rings must be used —one on each side of the O-ring.
Contoured / Concave Rings: Modern backup rings feature a concave curved face on one side. The concave surface must face toward the O-ring to cradle the rubber profile.
3. V-Ring Packings (Chevron Seals / AN6225)
V-ring packings are dynamic, one-way pressure-energized seals composed of multiple V-shaped elastomeric rings stacked between male (bottom) and female (top) matching adapters.
Installation Orientation Rule: The apex (point) of the 'V' must always face toward the source of fluid pressure .
When pressure is applied against the open pocket of the 'V', hydraulic fluid forces the inner and outer lips outward against the cylinder bore and piston rod, tightening the seal in direct proportion to system pressure.
If installed backward, fluid slips freely under the lips, causing complete seal blow-by.
4. Wiper Rings (Scrapers)
Wiper rings are metallic (beryllium copper, stainless steel) or synthetic rings installed in the outer gland of exposed actuator cylinders (e.g., landing gear oleo struts, flap jackscrews). Their sole function is to scrape away mud, ice, dust, and abrasive grit from the extending and retracting piston rod, preventing contamination from entering the internal packing gland.
5. Hydraulic Fluid Contamination & Filtration Systems
Contamination is the primary cause of hydraulic component wear, erratic valve operation, and in-flight power failures. Contaminants are classified into four major categories: ┌─────────────────────────────────────────────────────────────────────────────┐
- │ HYDRAULIC CONTAMINATION CLASSIFICATION │
- ├─────────────────────┬──────────────────────┬────────────────────────────────┤
- │ Particulate / Solid │ Moisture / Water │ Air / Gaseous Ingress │
- ├─────────────────────┼──────────────────────┼────────────────────────────────┤
- │ • Wear metals │ • Emulsification │ • Foaming & Spongy Controls │
- │ • Seal debris │ • Hydrolysis & Acids │ • Pump Cavitation & Erosion │
- │ • Airborne silica │ • Freezing at Alt. │ • Diesel Effect (Micro-Dieseling)│
- └─────────────────────┴──────────────────────┴────────────────────────────────┘
- 1. Particulate Contamination & Micron Ratings
Solid particulates include metallic wear shavings (steel, aluminum, bronze), silica dust, and degraded elastomer seal flakes.
Micron Definition: Particulate size is measured in micrometers (μm / microns) . 1 micron = 10 − 6 meter = 0.00003937 inch 1\text{ micron} = 10^{-6}\text{ meter} = 0.00003937\text{ inch} 1 micron = 1 0 − 6 meter = 0.00003937 inch . A human hair is approximately 70–100 microns in diameter; the human eye cannot detect particles smaller than ≈ 40 microns.
Clearance Criticality: Modern electrohydraulic servo valves (EHV) and axial piston pumps feature internal sliding clearances of 1 to 5 microns . Silt particles in this size range cause accelerated abrasive wear, valve sticking, and internal leakage.
Filter Media:
Micronic Filters: Cellulose (resin-impregnated paper) filters rated at 5 to 10 microns nominal . Paper elements are disposable and cannot be cleaned; they must be discarded and replaced at regular inspection intervals.
Sintered Metal & Stainless Steel Wire Mesh: Cleanable, reusable elements rated at 10–25 microns absolute, capable of withstanding extreme differential pressures. DIFFERENTIAL PRESSURE INDICATOR (PDI)
Uncontaminated / Normal Flow Clogged Element / Impending Bypass
- Filter Bowl Filter Bowl
- ┌────────────────┐ ┌────────────────┐
- │ Clean Filter │ │ Clogged Filter │
- │ Element │ │ Element │
- └───────┬────────┘ └───────┬────────┘
- │ │ High ΔP (>50 psi)
- ┌───┴───┐ ┌───┴───┐
- │ PDI │ (Flush) │ PDI │ ──► RED POP-OUT
- │ Button│ │ Button│ BUTTON EXTENDED
- └───────┘ └───────┘
- 2. Differential Pressure Indicators (PDI / DPI)
Filter assemblies incorporate a spring-loaded differential pressure indicator (PDI) (also called a pop-out button or Delta-P indicator). As contaminants collect on the filter element, the pressure drop (ΔP) across the element increases. When the differential pressure exceeds a predetermined threshold (typically 50–70 psi ):
The magnetic latch releases, driving a bright red indicator button out of the housing to alert maintenance personnel of an impending bypass condition.
Thermal lockout mechanisms prevent false PDI trip indications during cold morning starts when fluid viscosity is temporarily high.
If unserviced, further pressure increase opens an internal filter bypass valve , routing unfiltered fluid around the element to prevent element collapse and maintain uninterrupted flow to flight controls.
3. Water Contamination
Water enters hydraulic systems through atmospheric condensation in vented reservoirs, unsealed filler caps, or pressurized air supplies.
Chemical Degradation: In phosphate-ester fluids (Skydrol), water reacts chemically with the base stock via hydrolysis , forming corrosive phosphoric acid . The Total Acid Number (TAN) increases rapidly, attacking pump bearings, servo spools, and copper alloys.
High-Altitude Freezing: Free water droplets freeze into ice crystals at cruising altitudes (-50°F), lodging in servo valve orifices and locking flight control actuators.
4. Air Contamination & Cavitation
Air enters through loose suction-line B-nuts, defective pump shaft seals, or improper bleeding after component replacement.
Foaming & Spongy Action: Entrained air bubbles compress under load, transforming a rigid hydraulic column into an elastic spring. Flight controls become spongy, sluggish, and exhibit severe control lag.
Pump Cavitation: Air bubbles in the pump suction line implode violently under high cylinder discharge pressures, causing micro-jet impacts (> 100,000 psi localized force) that pit and erode pump cylinder blocks and valve plates.
Micro-Dieseling: Rapid adiabatic compression of entrained air/oil vapor generates localized temperatures exceeding 1,000°F, charring fluid and burning O-rings.