Study guide
1.2 Study Strategy, Blueprint Weighting & Core Formulas
FAA Aviation Mechanic — Airframe AMA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Strategy
1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas
2 Chapter 2: Metallic Structures & Sheet Metal Repair
2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs
3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics
3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors
4 Chapter 4: Welding & Structural Fasteners
4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
5 Chapter 5: Flight Controls, Assembly & Rigging
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention
6 Chapter 6: Hydraulic & Pneumatic Power Systems
6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control
7 Chapter 7: Aircraft Landing Gear Systems
7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems
8 Chapter 8: Aircraft Fuel Systems
8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety
9 Chapter 9: Airframe Electrical Systems
9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting
10 Chapter 10: Cabin Atmosphere & Environmental Control
10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators
11 Chapter 11: Aircraft Instrument Systems
11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections
12 Chapter 12: Communication, Navigation & Warning Systems
12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning
13 Chapter 13: Ice, Rain & Fire Protection Systems
13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture
14 Chapter 14: Airframe Inspection & Maintenance Regulations
14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT
15 Chapter 15: Rotorcraft Fundamentals
15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety
16 Chapter 16: Water & Waste Systems
16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety
1.2 Study Strategy, Blueprint Weighting & Core Formulas
Key Takeaways Explain This Topic AI
FAA-G-ACS-1 publishes the AMA blueprint as 15 knowledge areas with percentage ranges rather than fixed weights — Metallic Structures and Airframe Inspection at 5-15% each and the other 13 areas at 5-10% each — so even Rotorcraft Fundamentals and Water and Waste Systems are worth roughly 10 to 20 of the 100 questions and cannot be skipped.
Sheet metal layout requires mastering Bend Allowance ( B A = [ ( 0.01743 × R ) + ( 0.0078 × T ) ] × N BA = [(0.01743 \times R) + (0.0078 \times T)] \times N B A = [( 0.01743 × R ) + ( 0.0078 × T )] × N ) and Setback ( S B = ( R + T ) × K SB = (R + T) \times K SB = ( R + T ) × K ), where K = 1.0 K = 1.0 K = 1.0 for standard 90-degree bends.
Standard rivet layout rules mandate rivet diameter D = 3 × T thickest D = 3 \times T_{\text{thickest}} D = 3 × T thickest , total length L = Grip + 1.5 D L = \text{Grip} + 1.5D L = Grip + 1.5 D , edge distance 2 D 2D 2 D to 4 D 4D 4 D , and pitch 3 D 3D 3 D to 8 D 8D 8 D .
Fluid power calculations rely on Pascal's Law ( F = P × A F = P \times A F = P × A ) and annular retraction area calculations ( A effective = A piston − A rod A_{\text{effective}} = A_{\text{piston}} - A_{\text{rod}} A effective = A piston − A rod ).
A structured 6-week study schedule using active recall and spaced repetition optimizes question pacing (72 seconds per item) and minimizes common calculation traps.
Last updated: October 2026
1.2 Study Strategy, Blueprint Weighting & Core Formulas
Quick Summary: Success on the FAA Airframe (AMA) examination comes from studying the published blueprint rather than a guessed one. The FAA distributes the 100 questions across 15 knowledge areas and publishes each area's share as a percentage range , not a fixed number. Because every area carries a floor of about 5%, no subject can be safely skipped — and mastery of the recurring engineering formulas (bend allowance, setback, rivet sizing, Ohm's law, Pascal's law) makes the calculation items dependable points.
1. The Official AMA Blueprint (FAA-G-ACS-1)
The FAA publishes the mechanic written-test blueprints in FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards . The knowledge areas map one-to-one onto Section II (Airframe), Subjects A through O of FAA-S-ACS-1 , the ACS that 14 CFR §65.75(a) incorporates by reference.
Important
The FAA publishes ranges, not exact percentages. Any study source that hands you a precise split such as "Sheet Metal 14%, Hydraulics 11%, Electrical 10%" has invented those numbers. The FAA gives each of the 15 areas a band, and the bands deliberately overlap so that form-to-form question selection can vary.
Published Percentage of Test Questions by Knowledge Area
- # Knowledge Area (FAA-G-ACS-1) ACS Subject Published Share Approx. Questions
- 1 Metallic Structures II.A 5 – 15% 5 – 15
- 2 Non-Metallic Structures II.B 5 – 10% 5 – 10
- 3 Flight Controls II.C 5 – 10% 5 – 10
- 4 Airframe Inspection II.D 5 – 15% 5 – 15
- 5 Landing Gear Systems II.E 5 – 10% 5 – 10
- 6 Hydraulic and Pneumatic Systems II.F 5 – 10% 5 – 10
- 7 Environmental Systems II.G 5 – 10% 5 – 10
- 8 Aircraft Instrument Systems II.H 5 – 10% 5 – 10
- 9 Communication, Light Signals, and Runway Lighting Systems II.I 5 – 10% 5 – 10
- 10 Aircraft Fuel Systems II.J 5 – 10% 5 – 10
- 11 Aircraft Electrical Systems II.K 5 – 10% 5 – 10
- 12 Ice and Rain Control Systems II.L 5 – 10% 5 – 10
- 13 Airframe Fire Protection Systems II.M 5 – 10% 5 – 10
- 14 Rotorcraft Fundamentals II.N 5 – 10% 5 – 10
- 15 Water and Waste Systems II.O 5 – 10% 5 – 10
Naming note: FAA-G-ACS-1 titles area 9 "Communication, Light Signals, and Runway Lighting Systems," while the ACS itself titles Subject II.I "Communication and Navigation Systems." They are the same body of material — treat aircraft lighting, ATC light-gun signals, and airport lighting as fair game alongside VHF, VOR, ILS, DME, GPS, and transponders.
- How to Read the Ranges ┌──────────────────────────────────────────────────────────────────────┐
- │ AMA — 100 Questions / 15 Knowledge Areas │
- ├──────────────────────────────────────────────────────────────────────┤
- │ Two areas can reach 15%: Metallic Structures │
- │ Airframe Inspection │
- │ │
- │ Thirteen areas are 5-10%: every other knowledge area │
- │ │
- │ Guaranteed floor: ~5% (≈5 questions) in EVERY area │
- │ 15 areas x 5% floor = ~75 of the 100 questions are locked to │
- │ the floors; the remaining ~25 float │
- └──────────────────────────────────────────────────────────────────────┘
Three planning conclusions follow directly from the published numbers:
Structures and Inspection are the only two areas that can double up. They are the only areas whose band tops out at 15%, so together they can supply up to 30 questions. Weight your first pass accordingly.
No area is optional. Because the floor is roughly 5% everywhere, the smallest-looking subjects — Rotorcraft Fundamentals and Water and Waste Systems — still put roughly 5 to 10 questions each on your test. Skipping both can cost 10 to 20 questions, which is the difference between a comfortable pass and a fail at the 70% line.
Breadth beats depth on the margins. Reaching 100% on one 10% area gains less than moving from 40% to 80% across the five areas you have been ignoring.
Mapping the Blueprint to This Guide
- Knowledge Area Chapters in this guide
- Metallic Structures (incl. welding elements II.A.K10–K16) Chapters 2 and 4
- Non-Metallic Structures (composite, wood, fabric, windows) Chapter 3
- Flight Controls Chapter 5
- Hydraulic and Pneumatic Systems Chapter 6
- Landing Gear Systems Chapter 7
- Aircraft Fuel Systems Chapter 8
- Aircraft Electrical Systems Chapter 9
- Environmental Systems Chapter 10
- Aircraft Instrument Systems Chapter 11
- Communication, Light Signals, and Runway Lighting Chapter 12
- Ice and Rain Control + Airframe Fire Protection Chapter 13
- Airframe Inspection Chapter 14
- Rotorcraft Fundamentals Chapter 15
- Water and Waste Systems Chapter 16
2. Core Mathematical & Engineering Formulas
Mathematical calculations on the Airframe exam require absolute precision. Memorizing the formulas and understanding their physical derivations is mandatory. ┌─────────────────────────────────────────────────────────────────────────────┐
- │ Summary of Critical Airframe Formulas │
- ├─────────────────────────────────────────────────────────────────────────────┤
- │ Bend Allowance: BA = [(0.01743 × R) + (0.0078 × T)] × N │
- │ Setback: SB = (R + T) × K [where K = tan(A / 2)] │
- │ Rivet Diameter: D = 3 × T_thickest │
- │ Rivet Length: L = Grip + 1.5D │
- │ Ohm's Law: V = I × R | P = V × I = I²R = V² / R │
- │ Pascal's Law: F = P × A | P = F / A | A = F / P │
- │ Annular Area: A_effective = A_piston - A_rod │
- └─────────────────────────────────────────────────────────────────────────────┘
- A. Sheet Metal Bend Allowance ( B A BA B A )
When sheet metal is bent, the outer fibers stretch in tension while the inner fibers compress. Between the two lies the neutral axis , which does not change length. The neutral axis in aircraft aluminum alloys (such as 2024-T3) sits approximately 0.447 × T 0.447 \times T 0.447 × T from the inside radius. Bend Allowance ( B A ) = [ ( 0.01743 × R ) + ( 0.0078 × T ) ] × N \text{Bend Allowance } (BA) = \left[ (0.01743 \times R) + (0.0078 \times T) \right] \times N Bend Allowance ( B A ) = [ ( 0.01743 × R ) + ( 0.0078 × T ) ] × N
Where:
- R = R = R = Inside bend radius (inches)
- T = T = T = Material thickness (inches)
- N = N = N = Number of degrees in the bend (e.g., 90 ∘ 90^\circ 9 0 ∘ )
- 0.01743 = 2 π 360 0.01743 = \frac{2\pi}{360} 0.01743 = 360 2 π (radians per degree of radius)
0.0078 = 0.447 × 0.01743 0.0078 = 0.447 \times 0.01743 0.0078 = 0.447 × 0.01743 (neutral axis constant for sheet aluminum)
Worked Example:
Calculate the Bend Allowance for a 90 ∘ 90^\circ 9 0 ∘ bend in a 0.040-inch thick 2024-T3 aluminum sheet with an inside bend radius of 0.125 inches ( 1 / 8 1/8 1/8 in): B A = [ ( 0.01743 × 0.125 ) + ( 0.0078 × 0.040 ) ] × 90 BA = \left[ (0.01743 \times 0.125) + (0.0078 \times 0.040) \right] \times 90 B A = [ ( 0.01743 × 0.125 ) + ( 0.0078 × 0.040 ) ] × 90 B A = [ 0.00217875 + 0.00031200 ] × 90 = 0.00249075 × 90 = 0.2242 inches BA = \left[ 0.00217875 + 0.00031200 \right] \times 90 = 0.00249075 \times 90 = \mathbf{0.2242\text{ inches}} B A = [ 0.00217875 + 0.00031200 ] × 90 = 0.00249075 × 90 = 0.2242 inches
B. Setback ( S B SB SB ) and the K-Factor
Setback is the distance from the mould point (intersection of the extension of the two outer flange lines) to the bend tangent line (where the metal starts to curve). Setback ( S B ) = ( R + T ) × K \text{Setback } (SB) = (R + T) \times K Setback ( SB ) = ( R + T ) × K
Where:
K = tan ( A 2 ) K = \tan\left(\frac{A}{2}\right) K = tan ( 2 A ) where A A A is the angle of the bend.
For a standard 90 ∘ 90^\circ 9 0 ∘ bend : K = tan ( 45 ∘ ) = 1.0 K = \tan(45^\circ) = \mathbf{1.0} K = tan ( 4 5 ∘ ) = 1.0 . Thus, for 90 ∘ 90^\circ 9 0 ∘ : S B = R + T \mathbf{SB = R + T} SB = R + T .
For open bends ( < 90 ∘ <90^\circ < 9 0 ∘ ), K < 1.0 K < 1.0 K < 1.0 .
For closed bends ( > 90 ∘ >90^\circ > 9 0 ∘ ), K > 1.0 K > 1.0 K > 1.0 . Flat Layout Pattern Length = Mould Line Leg 1 − S B + B A + Mould Line Leg 2 − S B \text{Flat Layout Pattern Length} = \text{Mould Line Leg}_1 - SB + BA + \text{Mould Line Leg}_2 - SB Flat Layout Pattern Length = Mould Line Leg 1 − SB + B A + Mould Line Leg 2 − SB
C. Rivet Sizing and Layout Rules (AC 43.13-1B)
Parameter Standard Rule / Formula Engineering Rationale & Allowable Limits
Rivet Diameter ( D D D ) D = 3 × T thickest D = 3 \times T_{\text{thickest}} D = 3 × T thickest Diameter must be three times the thickness of the thickest sheet being joined. If the calculation yields an intermediate fraction, round UP to the next standard 1/32" increment.
Rivet Length ( L L L ) L = Grip + 1.5 D L = \text{Grip} + 1.5D L = Grip + 1.5 D Grip is the total stack thickness of all sheets. 1.5 D 1.5D 1.5 D provides sufficient protruding shank to form the standard bucked shop head ( 0.5 D 0.5D 0.5 D high by 1.5 D 1.5D 1.5 D wide).
Edge Distance ( E D ED E D ) 2 D to 4 D 2D \text{ to } 4D 2 D to 4 D Minimum edge distance is 2.0 × D 2.0 \times D 2.0 × D (from center of hole to edge of sheet) to prevent edge tearout; maximum is 4.0 × D 4.0 \times D 4.0 × D to prevent sheet puckering. For universal head rivets, 2 D 2D 2 D to 4 D 4D 4 D ; for flush countersunk rivets, 2.5 D 2.5D 2.5 D to 4 D 4D 4 D .
Rivet Pitch 3 D to 8 D 3D \text{ to } 8D 3 D to 8 D Spacing between adjacent rivets in the same row. Minimum is 3 D 3D 3 D (standard recommended is 4 D 4D 4 D to 6 D 6D 6 D ) to prevent sheet stress concentration; maximum is 8 D 8D 8 D to prevent buckling between rivets.
Transverse Pitch (Gage) 0.75 × Pitch (or ≥ 2.5 D ) 0.75 \times \text{Pitch} \text{ (or } \ge 2.5D\text{)} 0.75 × Pitch (or ≥ 2.5 D ) Distance between parallel rows of staggered rivets. Standard minimum is 75 % 75\% 75% of rivet pitch.
- 3. Fluid Power and Electrical Calculations
- A. Hydraulic Force, Pressure, and Annular Area
Fluid power systems operate on Pascal's Law , stating that pressure applied to a confined liquid is transmitted equally and undiminished in all directions. F = P × A ⟺ P = F A ⟺ A = F P F = P \times A \quad \Longleftrightarrow \quad P = \frac{F}{A} \quad \Longleftrightarrow \quad A = \frac{F}{P} F = P × A ⟺ P = A F ⟺ A = P F
Where:
- F = F = F = Force in pounds (lbs)
- P = P = P = Pressure in pounds per square inch (psi)
A = A = A = Piston area in square inches ( in 2 = π r 2 = π d 2 4 ≈ 0.7854 × d 2 \text{in}^2 = \pi r^2 = \frac{\pi d^2}{4} \approx 0.7854 \times d^2 in 2 = π r 2 = 4 π d 2 ≈ 0.7854 × d 2 )
The Double-Acting Actuator Annular Area Trap:
In a double-acting hydraulic actuator, the extension stroke acts upon the full piston surface area. On the retraction stroke , the fluid acts only on the annular area (piston area minus the rod cross-sectional area). A retract = A piston − A rod = π 4 ( D piston 2 − D rod 2 ) A_{\text{retract}} = A_{\text{piston}} - A_{\text{rod}} = \frac{\pi}{4}\left(D_{\text{piston}}^2 - D_{\text{rod}}^2\right) A retract = A piston − A rod = 4 π ( D piston 2 − D rod 2 ) Retract Force ( F retract ) = P × A retract \text{Retract Force } (F_{\text{retract}}) = P \times A_{\text{retract}} Retract Force ( F retract ) = P × A retract
B. Electrical Power and Ohm's Law
Airframe electrical questions frequently require combining Ohm's Law and Power equations: V = I × R P = V × I = I 2 R = V 2 R V = I \times R \qquad P = V \times I = I^2 R = \frac{V^2}{R} V = I × R P = V × I = I 2 R = R V 2
Circuit Configuration Rules:
Series Circuits: Current is constant ( I total = I 1 = I 2 I_{\text{total}} = I_1 = I_2 I total = I 1 = I 2 ). Total resistance is additive ( R total = R 1 + R 2 + R 3 R_{\text{total}} = R_1 + R_2 + R_3 R total = R 1 + R 2 + R 3 ). Voltage drops sum to source voltage ( V total = V 1 + V 2 + V 3 V_{\text{total}} = V_1 + V_2 + V_3 V total = V 1 + V 2 + V 3 ).
Parallel Circuits: Voltage is constant across all branches ( V total = V 1 = V 2 V_{\text{total}} = V_1 = V_2 V total = V 1 = V 2 ). Total current is additive ( I total = I 1 + I 2 + I 3 I_{\text{total}} = I_1 + I_2 + I_3 I total = I 1 + I 2 + I 3 ). Total resistance is always less than the smallest branch: 1 R total = 1 R 1 + 1 R 2 + 1 R 3 or for two resistors: R total = R 1 × R 2 R 1 + R 2 \frac{1}{R_{\text{total}}} = \frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3} \quad \text{or for two resistors: } R_{\text{total}} = \frac{R_1 \times R_2}{R_1 + R_2} R total 1 = R 1 1 + R 2 1 + R 3 1 or for two resistors: R total = R 1 + R 2 R 1 × R 2
4. High-Frequency Test Traps & Calculation Pitfalls
FAA test writers deliberately construct distractors around classic student calculation and conceptual errors. Avoid these common traps:
Radius vs. Diameter in Rivet Formulas:
Trap: Using the rivet radius instead of shank diameter ( D D D ) when calculating minimum edge distance ( 2 D 2D 2 D ) or shop head allowance ( 1.5 D 1.5D 1.5 D ).
Rule: Always express D D D as the full fractional diameter (e.g., 1 / 8 " = 0.125 " 1/8" = 0.125" 1/8" = 0.125" ).
Setback Deduction from Both Flanges:
Trap: Subtracting Setback ( S B SB SB ) only once when calculating the flat pattern length of a U-channel or Z-angle.
Rule: Setback must be subtracted from both flanges that meet at that bend corner.
Hydraulic Cylinder Rod Deduction:
Trap: Calculating retraction force using the full piston area without subtracting the rod cross-sectional area.
Rule: Always subtract A rod A_{\text{rod}} A rod from A piston A_{\text{piston}} A piston for retraction calculations.
24 Months Validity vs. 6-in-24 Currency:
Trap: Confusing the 24-month life of an AKTR ( §65.71(a)(3) , not §65.75) with the recent experience currency requirement ( §65.83 , which requires 6 months of qualifying work within the preceding 24 months).
Rule: §65.71 = getting certificated. §65.83 = staying able to exercise the privileges afterward.
Skydrol vs. Mineral Hydraulic Fluid Compatibility:
Trap: Mixing seals or fluids between MIL-PRF-5606 (mineral base, red color, requires Buna-N / Nitrile seals) and phosphate ester Skydrol (synthetic base, purple/green color, requires Butyl or Ethylene-Propylene seals). Mixing causes catastrophic seal degradation.
5. Recommended 6-Week Airframe Study Schedule
To achieve consistent scores above 90%, follow this structured 6-week progression utilizing spaced repetition and daily active recall testing. ┌───────────────┬─────────────────────────────────────────────────────────────┐
- │ Week │ Core Focus & Milestone Goals │
- ├───────────────┼─────────────────────────────────────────────────────────────┤
- │ Week 1 │ 14 CFR Regulations, ATA 100, Inspection & Fasteners │
- │ Week 2 │ Metallic Sheet Metal, Bend Calculations, Riveting & Tools │
- │ Week 3 │ Hydraulics, Pneumatics, Landing Gear & Brake Systems │
- │ Week 4 │ Aircraft Electrical, Power Generation, Avionics & Com/Nav │
- │ Week 5 │ Cabin Atmosphere (AC/Pressurization), Fuel & Fire Systems │
- │ Week 6 │ Full Timed Mocks (100 Qs / 120 mins) & ACS Weak-Area Drill │
- └───────────────┴─────────────────────────────────────────────────────────────┘
- Daily Pacing & Test-Taking Tactics
Pacing Budget: 100 questions in 120 minutes allows an average of 72 seconds per question . Complete the test in three structured passes:
Pass 1 (0–50 min): Answer all direct factual questions immediately. Mark all calculation or multi-step schematic questions.
Pass 2 (50–95 min): Solve marked calculation problems on scratch paper. Double-check all formula substitutions.
Pass 3 (95–115 min): Review all 100 questions. Ensure no question is left blank (there is no penalty for guessing; an unanswered question is scored incorrect).