Study guide

2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming

FAA Aviation Mechanic — Airframe AMA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Strategy

1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas

2 Chapter 2: Metallic Structures & Sheet Metal Repair

2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics

3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors

4 Chapter 4: Welding & Structural Fasteners

4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware

5 Chapter 5: Flight Controls, Assembly & Rigging

5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention

6 Chapter 6: Hydraulic & Pneumatic Power Systems

6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control

7 Chapter 7: Aircraft Landing Gear Systems

7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems

8 Chapter 8: Aircraft Fuel Systems

8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety

9 Chapter 9: Airframe Electrical Systems

9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting

10 Chapter 10: Cabin Atmosphere & Environmental Control

10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators

11 Chapter 11: Aircraft Instrument Systems

11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections

12 Chapter 12: Communication, Navigation & Warning Systems

12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning

13 Chapter 13: Ice, Rain & Fire Protection Systems

13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture

14 Chapter 14: Airframe Inspection & Maintenance Regulations

14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT

15 Chapter 15: Rotorcraft Fundamentals

15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

16 Chapter 16: Water & Waste Systems

16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety

2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming

Key Takeaways Explain This Topic AI

During sheet metal bending, outer fibers undergo tension (stretching) and inner fibers undergo compression (shrinking), while the neutral axis experiences zero length change at approximately 44.5% of sheet thickness.

Bend Allowance (BA) is calculated using the standard empirical formula: BA = [(0.01743 × R) + (0.0078 × T)] × N, where R is inside radius, T is thickness, and N is bend angle in degrees.

Setback (SB) is the distance from the mold point to the bend tangent line, calculated as SB = (R + T) × K, where K = tan(Bend Angle / 2); for a 90° bend, K = 1.0, making SB = R + T.

The sight line is always marked exactly one inside bend radius (1R) from the bend tangent line positioned under the brake radius nose bar.

Corner relief holes with a minimum diameter equal to the inside bend radius (D = R or D >= T) must be drilled at intersecting bend tangent lines to prevent severe stress concentration and corner cracking.

Last updated: August 2026

Sheet Metal Layout: Bend Allowance, Setback & Forming

FAA Airframe Exam Focus: Sheet metal layout calculations require exact geometric calculations for Flat Layout ( F L FL F L ), Bend Allowance ( B A BA B A ), Setback ( S B SB SB ), K-Factors, Sight Lines, and Corner Relief Holes. Mastery of these formulas is tested extensively on the FAA Airframe Knowledge and Practical Exams.

1. Mechanics of Bending & The Neutral Axis

When a flat sheet of aircraft aluminum is bent in a bending brake or over a form block, severe mechanical stress gradients develop across its cross-section: CROSS-SECTION OF BENT SHEET METAL:

  • ┌───────────────────────────────────────────┐ ◄── Outer Surface (TENSION / Stretching)
  • │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░│
  • ├- - - - - - - - - - - - - - - - - - - - - -┤ ◄── NEUTRAL AXIS (0.445T from inside)
  • │▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒│
  • └───────────────────────────────────────────┘ ◄── Inner Surface (COMPRESSION / Shrinking)
  • ▲
  • │◄──────── Inside Bend Radius (R) ────────►

Outer Surface (Tension): The metal fibers outside the center are stretched and thinned.

Inner Surface (Compression): The metal fibers on the inside of the curve are compressed and thickened.

Neutral Axis: An imaginary plane located within the sheet where the metal is neither stretched nor compressed. In aluminum alloys, the neutral axis lies approximately 0.445 × T 0.445 \times T 0.445 × T ( 44.5 % 44.5\% 44.5% of sheet thickness) from the inside radius surface.

2. Bend Allowance ( B A BA B A ) Calculation & Empirical Formula

Bend Allowance ( B A BA B A ) represents the exact curved length of material consumed between the two Bend Tangent Lines (BTL) around the bend: B A = [ ( 0.01743 × R ) + ( 0.0078 × T ) ] × N BA = \left[ (0.01743 \times R) + (0.0078 \times T) \right] \times N B A = [ ( 0.01743 × R ) + ( 0.0078 × T ) ] × N

where:

  • R R R = Inside bend radius (inches)
  • T T T = Sheet metal thickness (inches)
  • N N N = Number of degrees in the bend angle ( N = 90 ∘ N = 90^\circ N = 9 0 ∘ for a right angle)

Constant 0.01743 = 2 π 360 = π 180 0.01743 = \frac{2\pi}{360} = \frac{\pi}{180} 0.01743 = 360 2 π ​ = 180 π ​ (arc length per degree per unit radius)

Constant 0.0078 = 0.4475 × 0.01743 0.0078 = 0.4475 \times 0.01743 0.0078 = 0.4475 × 0.01743 (accounting for the neutral axis position) BEND GEOMETRY & TERMINOLOGY:

  • Mold Line 1
  • │
  • ▼ Mold Point (MP)
  • ┆ / ◄── Setback (SB) = (R + T) * K
  • Flange 1 ┆ *
  • (Flat) ┆ / ┆
  • ┆ / ┆
  • ┆ BTL 1 / ┆
  • ───────────┼──────────* ┆ ◄── Setback (SB)
  • │ ( ┆
  • │ BA ( ┆
  • │ Arc ( ┆
  • │ (BTL 2┆
  • │ *────┼─────────────────────── ◄── Flange 2 (Flat)
  • │ / ┆
  • │ / ┆
  • │ ▼ ▼
  • │ Bend Mold Line 2
  • │ Radius
  • │ (R)
  • 3. Setback ( S B SB SB ) and K-Factor Calculations

Setback ( S B SB SB ) is the distance from the Mold Point (MP) (intersection of the two outer mold lines) to the Bend Tangent Line (BTL) : S B = ( R + T ) × K SB = (R + T) \times K SB = ( R + T ) × K

where K K K is the K-factor , determined by the bend deflection angle: K = tan ⁡ ( Bend Angle 2 ) K = \tan\left(\frac{\text{Bend Angle}}{2}\right) K = tan ( 2 Bend Angle ​ )

Setback Behavior by Bend Type

90 ∘ 90^\circ 9 0 ∘ Bend: K = tan ⁡ ( 45 ∘ ) = 1.0 ⟹ S B = R + T K = \tan(45^\circ) = 1.0 \implies \mathbf{SB = R + T} K = tan ( 4 5 ∘ ) = 1.0 ⟹ SB = R + T

Open Bend ( < 90 ∘ <90^\circ < 9 0 ∘ deflection): K < 1.0 ⟹ S B < R + T K < 1.0 \implies SB < R + T K < 1.0 ⟹ SB < R + T

Closed Bend ( > 90 ∘ >90^\circ > 9 0 ∘ deflection): K > 1.0 ⟹ S B > R + T K > 1.0 \implies SB > R + T K > 1.0 ⟹ SB > R + T

Bend Angle ( N N N ) K-Factor ( K = tan ⁡ ( N / 2 ) K = \tan(N/2) K = tan ( N /2 ) ) Setback Formula ( S B SB SB )

30 ∘ 30^\circ 3 0 ∘ 0.2679 0.2679 0.2679 S B = ( R + T ) × 0.2679 SB = (R + T) \times 0.2679 SB = ( R + T ) × 0.2679

45 ∘ 45^\circ 4 5 ∘ 0.4142 0.4142 0.4142 S B = ( R + T ) × 0.4142 SB = (R + T) \times 0.4142 SB = ( R + T ) × 0.4142

60 ∘ 60^\circ 6 0 ∘ 0.5774 0.5774 0.5774 S B = ( R + T ) × 0.5774 SB = (R + T) \times 0.5774 SB = ( R + T ) × 0.5774

90 ∘ 90^\circ 9 0 ∘ 1.0000 1.0000 1.0000 S B = R + T \mathbf{SB = R + T} SB = R + T

120 ∘ 120^\circ 12 0 ∘ 1.7321 1.7321 1.7321 S B = ( R + T ) × 1.7321 SB = (R + T) \times 1.7321 SB = ( R + T ) × 1.7321

135 ∘ 135^\circ 13 5 ∘ 2.4142 2.4142 2.4142 S B = ( R + T ) × 2.4142 SB = (R + T) \times 2.4142 SB = ( R + T ) × 2.4142

4. Flat Pattern Layout ( F L FL F L ) Calculation

To cut a flat sheet that will form into precise finished flange dimensions after bending, calculate the Flat Layout ( F L FL F L ) length:

Single 90 ∘ 90^\circ 9 0 ∘ Bend (L-Angle Flange) F L = ( Flange 1 − S B ) + B A + ( Flange 2 − S B ) FL = (\text{Flange } 1 - SB) + BA + (\text{Flange } 2 - SB) F L = ( Flange 1 − SB ) + B A + ( Flange 2 − SB )

Double 90 ∘ 90^\circ 9 0 ∘ Bend (U-Channel Section) F L = ( Flange 1 − S B 1 ) + B A 1 + ( Web − S B 1 − S B 2 ) + B A 2 + ( Flange 2 − S B 2 ) FL = (\text{Flange } 1 - SB_1) + BA_1 + (\text{Web} - SB_1 - SB_2) + BA_2 + (\text{Flange } 2 - SB_2) F L = ( Flange 1 − S B 1 ​ ) + B A 1 ​ + ( Web − S B 1 ​ − S B 2 ​ ) + B A 2 ​ + ( Flange 2 − S B 2 ​ )

Comprehensive Numerical Worked Example

Problem: Calculate the flat layout pattern length ( F L FL F L ) for an aluminum channel made from 0.050 " 0.050" 0.050" 2024-T3 sheet with an inside bend radius R = 0.150 " R = 0.150" R = 0.150" , two 90 ∘ 90^\circ 9 0 ∘ bends, outer flange legs of 1.250 " 1.250" 1.250" each, and an overall outer web dimension of 3.500 " 3.500" 3.500" . U-CHANNEL SPECIFICATIONS:

  • Flange 1 = 1.250" Flange 2 = 1.250"
  • ┌───┐ ┌───┐
  • │ │ │ │
  • │ │ │ │
  • │ └───┐ ┌───┘ │
  • │ └─────────────────────────────┘ │
  • └─────────────────────────────────────────────┘
  • Web (Outer) = 3.500"
  • T = 0.050", R = 0.150", Bend Angles = 90°

Calculate Setback ( S B SB SB ): S B = ( R + T ) × K = ( 0.150 " + 0.050 " ) × 1.0 = 0.200 " SB = (R + T) \times K = (0.150" + 0.050") \times 1.0 = 0.200" SB = ( R + T ) × K = ( 0.150" + 0.050" ) × 1.0 = 0.200"

Calculate Bend Allowance ( B A BA B A ) per bend: B A = [ ( 0.01743 × 0.150 ) + ( 0.0078 × 0.050 ) ] × 90 BA = [(0.01743 \times 0.150) + (0.0078 \times 0.050)] \times 90 B A = [( 0.01743 × 0.150 ) + ( 0.0078 × 0.050 )] × 90 B A = [ 0.0026145 + 0.00039 ] × 90 = 0.0030045 × 90 = 0.2704 " BA = [0.0026145 + 0.00039] \times 90 = 0.0030045 \times 90 = 0.2704" B A = [ 0.0026145 + 0.00039 ] × 90 = 0.0030045 × 90 = 0.2704"

Calculate Flat Sections:

Flat 1 = Flange 1 − S B = 1.250 " − 0.200 " = 1.050 " \text{Flat } 1 = \text{Flange } 1 - SB = 1.250" - 0.200" = 1.050" Flat 1 = Flange 1 − SB = 1.250" − 0.200" = 1.050"

Flat Web = Web − ( 2 × S B ) = 3.500 " − 0.400 " = 3.100 " \text{Flat Web} = \text{Web} - (2 \times SB) = 3.500" - 0.400" = 3.100" Flat Web = Web − ( 2 × SB ) = 3.500" − 0.400" = 3.100"

Flat 2 = Flange 2 − S B = 1.250 " − 0.200 " = 1.050 " \text{Flat } 2 = \text{Flange } 2 - SB = 1.250" - 0.200" = 1.050" Flat 2 = Flange 2 − SB = 1.250" − 0.200" = 1.050"

Sum Flat Layout Length ( F L FL F L ): F L = Flat 1 + B A 1 + Flat Web + B A 2 + Flat 2 FL = \text{Flat } 1 + BA_1 + \text{Flat Web} + BA_2 + \text{Flat } 2 F L = Flat 1 + B A 1 ​ + Flat Web + B A 2 ​ + Flat 2 F L = 1.050 " + 0.2704 " + 3.100 " + 0.2704 " + 1.050 " = 5.7408 " FL = 1.050" + 0.2704" + 3.100" + 0.2704" + 1.050" = \mathbf{5.7408"} F L = 1.050" + 0.2704" + 3.100" + 0.2704" + 1.050" = 5.7408"

5. Sight Line Layout & Bending Brake Setup

When inserting sheet metal into a cornice brake or box-and-pan brake, the technician cannot see the bend tangent lines directly underneath the nose bar. To position the bend precisely: SIGHT LINE IN BENDING BRAKE:

  • Brake Clamping Leaf / Nose Bar
  • ┌──────────────┐
  • │ │
  • │ │
  • │ (R) │
  • ──────────────────┴──────────────*─────────────── ◄── Sight Line (Marked on Sheet)
  • ◄── Clamped in Brake ──► │
  • ◄──── Flat 1 ────►│◄─── 1R ─────►│ ◄── BTL 1 (Bend Tangent Line)
  • │◄──── BA ────►│

Sight Line Rule: The sight line is always drawn on the flat layout one inside bend radius ( 1 R 1R 1 R ) from the bend tangent line that is clamped under the brake radius nose bar.

Brake Operation: Align the sight line directly with the forward edge of the brake nose bar radius. When the brake clamping leaf is locked, the bend tangent line ( B T L BTL BT L ) is positioned exactly where the curvature begins.

6. Grain Orientation & Minimum Bend Radii

During rolling at the aluminum mill, alloy grains elongate in the direction of sheet rolling: GRAIN DIRECTION vs. BEND CRACKING:

  • [ BEST: 90° Across Grain ] [ WORST: Parallel with Grain ]
  • Bend Line Bend Line
  • │ ═════════
  • ═══════╪═══════ ◄── Grain Direction ───────═════════─────── ◄── Grain Direction
  • ═══════╪═══════ ───────═════════───────
  • │
  • Maximum Ductility, Severe Tensile Cracking Along

No Cracking Grain Boundaries!

Rule of Forming: Always bend perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) across the grain of the metal whenever possible. If layout requires angular bends, keep bends at 45 ∘ 45^\circ 4 5 ∘ to the grain. Never bend parallel to the grain , as outer fiber tensile stresses cause grain boundary separation and cracking.

Minimum Bend Radius ( R m i n R_{min} R min ​ ): The sharpest inside radius to which an alloy sheet can be bent without cracking. Harder tempers (-T6) require larger bend radii ( 3 T 3T 3 T to 6 T 6T 6 T ), whereas annealed sheets (-O) can be formed over tight radii ( 1 T 1T 1 T to 2 T 2T 2 T ).

7. Corner Relief Holes (Stress Relieving)

When two flanged bends intersect at a 90 ∘ 90^\circ 9 0 ∘ corner (e.g., box corners, rib flanges, bulkheads), the intersecting bend tangent lines concentrate extreme shearing stresses during forming: CORNER RELIEF HOLE LAYOUT:

  • Flange 1 ─────────────────────────┐
  • │
  • - - - - - - - - - - - - - BTL 1 │
  • │
  • ─────────────────────────────┐ │

│ (O)│ ◄── Relief Hole: Center at BTL Intersection!

  • │ │ Diameter >= Inside Bend Radius (D >= R)
  • - - - - - - - - - - - BTL 2│ │
  • │ │
  • Flange 2 ────────────────────┘ │

Relief Hole Purpose: Eliminates sharp square inside corners, replacing stress-concentrating notches with a smooth radiused circle that prevents corner tearing.

Diameter Sizing: The hole diameter must be at least equal to the inside bend radius: D relief = R D_{\text{relief}} = R D relief ​ = R (or D ≥ T D \ge T D ≥ T , with 1 / 8 " 1/8" 1/8" ( 0.125 " 0.125" 0.125" ) being standard shop minimum).

Location: The center of the relief hole is drilled precisely at the intersection point of the inner bend tangent lines ( B T L BTL BT L ) .