Study guide

2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards

FAA Aviation Mechanic — Airframe AMA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Strategy

1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas

2 Chapter 2: Metallic Structures & Sheet Metal Repair

2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics

3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors

4 Chapter 4: Welding & Structural Fasteners

4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware

5 Chapter 5: Flight Controls, Assembly & Rigging

5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention

6 Chapter 6: Hydraulic & Pneumatic Power Systems

6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control

7 Chapter 7: Aircraft Landing Gear Systems

7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems

8 Chapter 8: Aircraft Fuel Systems

8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety

9 Chapter 9: Airframe Electrical Systems

9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting

10 Chapter 10: Cabin Atmosphere & Environmental Control

10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators

11 Chapter 11: Aircraft Instrument Systems

11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections

12 Chapter 12: Communication, Navigation & Warning Systems

12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning

13 Chapter 13: Ice, Rain & Fire Protection Systems

13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture

14 Chapter 14: Airframe Inspection & Maintenance Regulations

14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT

15 Chapter 15: Rotorcraft Fundamentals

15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

16 Chapter 16: Water & Waste Systems

16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety

2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards

Key Takeaways Explain This Topic AI

The standard rule of thumb for rivet diameter selection is three times the thickness of the thickest sheet in the joint (D = 3T).

Edge distance (ED) from hole center to sheet edge must be a minimum of 2D (maximum 4D) for protruding universal heads (MS20470) and a minimum of 2.5D for flush countersunk heads (MS20426).

Rivet pitch (spacing along a row) ranges from a minimum of 3D to a standard 4D–6D (maximum 8D), while transverse pitch (row spacing) is typically 75% of pitch (minimum 2.5D).

Total rivet length is calculated as total sheet thickness (grip length G) plus 1.5 times the rivet shank diameter (L = G + 1.5D).

A properly formed shop head (bucktail) must have a height equal to 0.5D (1/2D) and a diameter equal to 1.5D (1-1/2D).

Last updated: August 2026

Rivet Layout, Edge Distance, Spacing & Driving Standards

FAA Airframe Exam Focus: Structural joint integrity depends upon precise layout calculations (Rivet Diameter, Edge Distance, Pitch, Transverse Pitch, and Grip Length) and adherence to strict driven shop head (bucktail) dimensional tolerances per FAA AC 43.13-1B and MIL-R-47196.

1. Rivet Diameter Selection Rule ( D = 3 T D = 3T D = 3 T )

Selecting the correct rivet shank diameter ( D D D ) balances the shear strength of the fastener against the bearing strength of the parent sheet metal: D nominal = 3 × T thickest D_{\text{nominal}} = 3 \times T_{\text{thickest}} D nominal ​ = 3 × T thickest ​

where T thickest T_{\text{thickest}} T thickest ​ is the thickness of the thickest individual sheet comprising the joint. SHEAR FAILURE vs. BEARING FAILURE:

  • [ Rivet Too Small (D < 3T) ] [ Rivet Too Large (D > 3T) ]
  • ───► ───►
  • ═══════╤═══════ ═══════│░░░░│═══════ ◄── Sheet Crushed/Buckled
  • ───────┼─────── ◄── Rivet Shears ───────│░░░░│─────── (Bearing Failure)
  • ═══════╧═══════ ═══════│░░░░│═══════
  • ◄─── ◄───

If the rivet diameter is too small ( D < 3 T D < 3T D < 3 T ): The fastener lacks sufficient cross-sectional area to carry structural shear loads; the joint fails in pure rivet shear .

If the rivet diameter is too large ( D > 3 T D > 3T D > 3 T ): The high driving force required to upset a massive shank crushes the thin surrounding sheet metal, causing bearing failure , sheet puckering, and sheet elongation.

Rivet Sizing Nomenclature

Diameter: Designated in 1/32-inch increments (e.g., -3 = 3 / 32 " 3/32" 3/32" , -4 = 4 / 32 " = 1 / 8 " 4/32" = 1/8" 4/32" = 1/8" , -5 = 5 / 32 " 5/32" 5/32" , -6 = 3 / 16 " 3/16" 3/16" , -8 = 1 / 4 " 1/4" 1/4" ).

Length: Designated in 1/16-inch increments (e.g., -4 = 4 / 16 " = 1 / 4 " 4/16" = 1/4" 4/16" = 1/4" , -6 = 6 / 16 " = 3 / 8 " 6/16" = 3/8" 6/16" = 3/8" , -8 = 8 / 16 " = 1 / 2 " 8/16" = 1/2" 8/16" = 1/2" ).

Example Part Number: MS20470AD4-6 = Universal head (MS20470), 2117-T4 alloy (AD), 4 / 32 " 4/32" 4/32" ( 1 / 8 " 1/8" 1/8" ) shank diameter, 6 / 16 " 6/16" 6/16" ( 3 / 8 " 3/8" 3/8" ) length.

2. Rivet Layout Geometry: Edge Distance, Pitch & Transverse Pitch

To ensure even load distribution and prevent structural tearing or moisture ingress, rivet patterns must adhere to strict geometric spacing limits. RIVET PATTERN GEOMETRY (Staggered Pattern):

  • ◄─── ED ───►
  • ┌──────────┬──────────────┬──────────────┬──────────┐
  • │ │ │ │ │
  • │ (•) │ (•) │ (•) │ (•) │ ◄── Row 1
  • │ │ │ │ │ │ │ │
  • │ │ │◄──── Pitch ─►│ │ │ │
  • │ │ │ │ │ │ │
  • │ │◄─── Transverse ───►│ │ │ │
  • │ │ Pitch │ │ │ │
  • │ └────────────(•)─────┴──────┴──────(•)─────────┤ ◄── Row 2
  • │ │ │
  • └──────────────────┴────────────────────────────────┘
  • Critical Spacing Rules (AC 43.13-1B, Chapter 4)

Spacing Parameter Minimum Limit Standard / Preferred Maximum Limit Engineering Consequence of Violation

Edge Distance ( E D ED E D ) ; (Universal MS20470) 2.0 D 2.0D 2.0 D 2.5 D 2.5D 2.5 D 4.0 D 4.0D 4.0 D < 2 D <2D < 2 D : Sheet tears out at edge (tear-out shear).; > 4 D >4D > 4 D : Sheet edge curls, puckers, allows moisture intrusion.

Edge Distance ( E D ED E D ) ; (Countersunk MS20426) 2.5 D 2.5D 2.5 D 3.0 D 3.0D 3.0 D 4.0 D 4.0D 4.0 D Countersinking removes edge material; higher E D ED E D prevents knife-edge cracking and edge rollover.

Rivet Pitch ( P P P ) ; (Spacing along single row) 3.0 D 3.0D 3.0 D 4.0 D 4.0D 4.0 D to 6.0 D 6.0D 6.0 D 8.0 D 8.0D 8.0 D to 10.0 D 10.0D 10.0 D < 3 D <3D < 3 D : "Postage stamp" tear across row.; > 8 D >8D > 8 D : Skin buckles/oil-cans between rivets under compression.

Transverse Pitch ( T P TP TP ) ; (Distance between rows) 2.5 D 2.5D 2.5 D (or 0.75 × P 0.75 \times P 0.75 × P ) 3.0 D 3.0D 3.0 D 5.0 D 5.0D 5.0 D Minimum distance prevents inter-row sheet shear failure in multi-row lap joints.

3. Rivet Length Calculation ( L = G + 1.5 D L = G + 1.5D L = G + 1.5 D )

Before driving, the rivet shank must extend through the sheets with sufficient material to form a standard bucktail: L = G + 1.5 D L = G + 1.5D L = G + 1.5 D

where:

L L L = Total rivet shank length (inches)

G G G = Grip length (combined total thickness of all sheets being joined, G = T 1 + T 2 + … G = T_1 + T_2 + \dots G = T 1 ​ + T 2 ​ + … )

1.5 D 1.5D 1.5 D = Allowance required to form the upset shop head ( 1 1 2 × rivet diameter 1\frac{1}{2} \times \text{rivet diameter} 1 2 1 ​ × rivet diameter ) RIVET LENGTH & SHOP HEAD GEOMETRY:

  • [ BEFORE DRIVING ] [ AFTER DRIVING (UPSET) ]
  • ┌───────────┐ Manufactured ┌───────────┐ Manufactured
  • │ │ Head │ │ Head
  • ═══╧═══════════╧═══ ═══╧═══════════╧═══
  • ═══╤═══════════╤═══ ◄── Grip Length (G) ═══╤═══════════╤═══ ◄── Grip (G)
  • │ │ │ │
  • │ │ ◄── 1.5D Allowance ┌───────────┐ ◄── Height = 0.5D
  • └───────────┘ └───┴───────┴───┘ ◄── Width = 1.5D
  • Shank (D) Driven Shop Head (Bucktail)
  • Step-by-Step Calculation Example

Problem: Calculate the correct rivet size to join two 0.040 " 0.040" 0.040" 2024-T3 aluminum sheets using MS20470AD rivets.

Calculate Diameter ( D D D ): D = 3 × T = 3 × 0.040 " = 0.120 " D = 3 \times T = 3 \times 0.040" = 0.120" D = 3 × T = 3 × 0.040" = 0.120" . Select standard size: 1 / 8 " 1/8" 1/8" ( 0.125 " 0.125" 0.125" or -4 diameter).

Calculate Grip Length ( G G G ): G = 0.040 " + 0.040 " = 0.080 " G = 0.040" + 0.040" = 0.080" G = 0.040" + 0.040" = 0.080" .

Calculate Shop Head Allowance ( 1.5 D 1.5D 1.5 D ): 1.5 × 0.125 " = 0.1875 " 1.5 \times 0.125" = 0.1875" 1.5 × 0.125" = 0.1875" .

Calculate Total Length ( L L L ): L = 0.080 " + 0.1875 " = 0.2675 " L = 0.080" + 0.1875" = 0.2675" L = 0.080" + 0.1875" = 0.2675" .

Convert to 1/16th inch increments: 0.2675 " × 16 = 4.28 → 0.2675" \times 16 = 4.28 \to 0.2675" × 16 = 4.28 → round to nearest standard 1/16th: 5 / 16 " 5/16" 5/16" ( 0.3125 " 0.3125" 0.3125" , -5 length).

Final Part Number: MS20470AD4-5 .

4. Driven Shop Head (Bucktail) Dimensions & Tolerances

A properly driven solid rivet must conform to precise dimensional standards (verified using go/no-go rivet gauges): Shop Head Height = 0.5 D = 1 2 D \text{Shop Head Height} = 0.5D = \frac{1}{2} D Shop Head Height = 0.5 D = 2 1 ​ D Shop Head Diameter (Width) = 1.5 D = 1 1 2 D \text{Shop Head Diameter (Width)} = 1.5D = 1\frac{1}{2} D Shop Head Diameter (Width) = 1.5 D = 1 2 1 ​ D

Rivet Shank Diameter ( D D D ) Shop Head Height ( 0.5 D 0.5D 0.5 D ) Minimum Allowable Height Shop Head Width ( 1.5 D 1.5D 1.5 D ) Minimum Allowable Width

3 / 32 " 3/32" 3/32" ( 0.0938 " 0.0938" 0.0938" ) 0.0469 " 0.0469" 0.0469" ( 3 / 64 " 3/64" 3/64" ) 0.038 " 0.038" 0.038" 0.1406 " 0.1406" 0.1406" ( 9 / 64 " 9/64" 9/64" ) 0.125 " 0.125" 0.125" ( 1 / 8 " 1/8" 1/8" )

1 / 8 " 1/8" 1/8" ( 0.1250 " 0.1250" 0.1250" ) 0.0625 " 0.0625" 0.0625" ( 1 / 16 " 1/16" 1/16" ) 0.050 " 0.050" 0.050" 0.1875 " 0.1875" 0.1875" ( 3 / 16 " 3/16" 3/16" ) 0.160 " 0.160" 0.160" ( 5 / 32 " 5/32" 5/32" )

5 / 32 " 5/32" 5/32" ( 0.1562 " 0.1562" 0.1562" ) 0.0781 " 0.0781" 0.0781" ( 5 / 64 " 5/64" 5/64" ) 0.063 " 0.063" 0.063" 0.2344 " 0.2344" 0.2344" ( 15 / 64 " 15/64" 15/64" ) 0.200 " 0.200" 0.200" ( 13 / 64 " 13/64" 13/64" )

3 / 16 " 3/16" 3/16" ( 0.1875 " 0.1875" 0.1875" ) 0.0938 " 0.0938" 0.0938" ( 3 / 32 " 3/32" 3/32" ) 0.075 " 0.075" 0.075" 0.2812 " 0.2812" 0.2812" ( 9 / 32 " 9/32" 9/32" ) 0.250 " 0.250" 0.250" ( 1 / 4 " 1/4" 1/4" )

  • 5. Riveting Tooling, Driving Technique & Defect Analysis
  • Tooling & Assembly Procedures

Cleco Fasteners: Spring-loaded temporary clamping fasteners used to hold sheets in rigid alignment during drilling and riveting. Color codes: Silver ( 3 / 32 " 3/32" 3/32" ), Copper ( 1 / 8 " 1/8" 1/8" ), Black ( 5 / 32 " 5/32" 5/32" ), Brass ( 3 / 16 " 3/16" 3/16" ).

Pneumatic Rivet Guns: Rated by stroke capacity (2X for 3 / 32 " 3/32" 3/32" , 3X for 1 / 8 " 1/8" 1/8" to 5 / 32 " 5/32" 5/32" , 4X for 3 / 16 " 3/16" 3/16" to 1 / 4 " 1/4" 1/4" ). Rivet gun must be held exactly perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) to the skin.

Bucking Bar Selection: Bucking bar mass must be matched to rivet diameter. The face must be held square against the shank end without bouncing.

Riveting Defect Identification & Causes COMMON RIVET DEFECTS:

  • Underdriven Overdriven Offset/Clenched Cracked Head Loose / Fretting
  • ┌───┐ ┌───┐ ┌───┐ ┌───┐ ┌───┐
  • ═══╧═══╧═══ ═══╧═══╧═══ ═══╧═══╧═══ ═══╧═══╧═══ ═══╧═══╧═══
  • │ │ │ │ │ │ │ │ ▒ ▒
  • ┌┴───┴┐ ┌─────────┐ ┌─┴───┘ ┌┴──/─┴┐ ┌┴───┴┐ ◄── Black Oxide
  • │ │ └─────────┘ └───┘ │ / │ │ │ "Smoking"
  • H > 0.5D H < 0.5D Bar Tilted Aged Past Hole Elongated
  • W < 1.5D W > 1.5D Time Window

Defect Description Physical Characteristics Root Cause Rejection / Repair Action

Underdriven Rivet Shop head height > 0.5 D >0.5D > 0.5 D , diameter < 1.5 D <1.5D < 1.5 D ; shank did not fully expand. Gun removed prematurely; bucking bar too light. Reject. Drill out manufactured head and replace.

Overdriven Rivet Shop head height < 0.5 D <0.5D < 0.5 D , diameter > 1.5 D >1.5D > 1.5 D ; parent metal crushed. Gun operated too long; bucking bar too heavy. Reject if bucktail is cracked or skin is severely dimpled.

Clenched / Offset Head Bucktail bent over sideways; not concentric with shank. Bucking bar held at an angle; rivet shank too long. Reject. Replace fastener.

Cracked Bucktail Radial or circumferential splits in shop head. Driving icebox rivets after time window; overdriving. Reject. Replace fastener.

Loose / "Smoking" Rivet Black fretting corrosion rings ( A l 2 O 3 Al_2O_3 A l 2 ​ O 3 ​ powder) around head. Vibration / cyclic shear fatigue; hole enlarged. Drill out, ream hole to next 1 / 32 " 1/32" 1/32" oversize, drive oversize rivet.

"Smileys" / Skin Ding Crescent-shaped indentation in sheet next to head. Rivet set slipped off manufactured head. Evaluate per SRM allowable skin damage limits.

Proper Rivet Removal Procedure

Center-punch the exact center of the manufactured head.

Drill through the head using a drill bit equal to or one size smaller than the rivet shank, stopping exactly at the base of the head.

Snap off the rivet head using a pin punch.

Drive out the remaining shank with a drift punch while supporting the back of the structure with a bucking bar to avoid enlarging or elongating the hole.