Study guide

2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

FAA Aviation Mechanic — Airframe AMA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Strategy

1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas

2 Chapter 2: Metallic Structures & Sheet Metal Repair

2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics

3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors

4 Chapter 4: Welding & Structural Fasteners

4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware

5 Chapter 5: Flight Controls, Assembly & Rigging

5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention

6 Chapter 6: Hydraulic & Pneumatic Power Systems

6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control

7 Chapter 7: Aircraft Landing Gear Systems

7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems

8 Chapter 8: Aircraft Fuel Systems

8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety

9 Chapter 9: Airframe Electrical Systems

9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting

10 Chapter 10: Cabin Atmosphere & Environmental Control

10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators

11 Chapter 11: Aircraft Instrument Systems

11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections

12 Chapter 12: Communication, Navigation & Warning Systems

12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning

13 Chapter 13: Ice, Rain & Fire Protection Systems

13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture

14 Chapter 14: Airframe Inspection & Maintenance Regulations

14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT

15 Chapter 15: Rotorcraft Fundamentals

15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

16 Chapter 16: Water & Waste Systems

16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety

2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

Key Takeaways Explain This Topic AI

Aircraft structures are categorized into Primary (flight-critical/load-bearing), Secondary (aerodynamic load-carrying), and Tertiary (non-structural) components.

Damage is classified into four standard levels per AC 43.13-1B and SRM: Negligible Damage, Repairable by Patching, Repairable by Insertion, and Damage Requiring Replacement.

Fatigue cracks are arrested by stop-drilling the microscopic crack tip with a #30 or #40 drill bit after positive identification using dye penetrant or 10X optical magnification.

Flush patches require a cutout with radiused corners (minimum 0.50 in), an internal doubler made of the same alloy and one gauge thicker than the skin, and a flush filler plug of identical gauge and alloy.

Machine countersinking is restricted to sheets where thickness exceeds rivet head depth (typically T >= 0.040 in); thinner sheets (< 0.040 in) must be coin dimpled or radius dimpled to prevent knife-edge bearing failure.

Last updated: August 2026

Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

FAA Airframe Exam Focus: Airframe mechanics must evaluate structural damage against the aircraft Structural Repair Manual (SRM) and FAA AC 43.13-1B, execute precise crack arrest (stop-drilling), calculate doubler and fastener layouts for flush and lap repairs, and select between machine countersinking and coin dimpling.

1. Aircraft Structural Classifications & Stress Distribution

Aircraft structural components are categorized according to their criticality to flight safety and the primary mechanical loads they sustain: PRIMARY AIRCRAFT STRUCTURAL STRESSES:

  • [ TENSION ] [ COMPRESSION ] [ SHEAR ] [ TORSION ] [ BENDING ]
  • ◄───[ ]───► ───►[ ]◄─── ▲ ┌───┐ ┌───┐ ↻ ▼ ┌───────┐ ▼
  • │ │ │ │ │ ↺ │ │
  • Pulling Apart Crushing Force ▼ └───┘ └───┘ ──┴───────┴──
  • (Lower Wing Skin) (Upper Wing Skin) (Rivet Joints) (Wing Torque Box) (Wing Spars)

Classification Definition & Criticality Typical Airframe Components Approved Repair Authority

Primary Structure Flight-critical load-bearing members whose failure would result in catastrophic structural collapse or loss of aircraft control. Wing spars, spar caps, fuselage longerons, carry-through bulkheads, pressurized cabin skins, control surface spars. Manufacturer SRM or FAA-approved engineering data (DER / Form 337).

Secondary Structure Highly stressed members that carry aerodynamic or internal loads, but whose failure would not cause immediate loss of flight safety. Wing ribs, stringers, leading edge skin panels, floor beams, control surface skins. Manufacturer SRM, or AC 43.13-1B (if SRM unavailable).

Tertiary Structure Lightly loaded or non-structural elements that define aerodynamic fairings or internal cabin layout. Wheel fairings, non-pressurized access doors, cabin partitions, wing tips. Standard sheet metal repair practices per AC 43.13-1B.

2. Damage Assessment & Classification Standards

Per FAA AC 43.13-1B (Chapter 4) and manufacturer Structural Repair Manuals (SRM), structural damage is categorized into four distinct levels:

Negligible Damage: Minor scratches, small surface abrasions, tiny shallow dents, or shallow corrosion within published limits that do not compromise structural strength or aerodynamic smoothness.

Action: Blend out surface scratches with fine abrasive pads (maintaining a minimum 20:1 smooth blend taper ratio ), clean, treat with chemical conversion coating (Alodine), and prime.

Damage Repairable by Patching: Moderate skin punctures, small localized tears, or cracks in low-speed or secondary structure that can be reinforced by adding an external lap patch or internal doubler.

Damage Repairable by Insertion (Flush Patching): Severe skin damage on high-speed aerodynamic surfaces or pressurized fuselages where the damaged section is cut out and replaced with an internal doubler and flush filler plug.

Damage Requiring Replacement: Severe structural deformation, widespread distortion of primary load-carrying spars, buckled pressure bulkheads, or damage exceeding maximum SRM repair limits.

3. Crack Arrest Procedures (Stop-Drilling)

Fatigue cracks propagate due to extreme tensile stress concentrations at the sharp, microscopic root of the crack tip. Stop-drilling eliminates this stress notch, distributing loads around a smooth radiused hole. STOP-DRILLING PROCEDURE:

  • 1. Pinpoint Microscopic Crack Tip (Dye Penetrant / 10X Glass)
  • ═══════════════════════════════════════► (Crack Tip)
  • 2. Drill Stop Hole with #30 or #40 Bit
  • ═══════════════════════════════════════( O )
  • ▲
  • └── Crack Tip Fully Contained in Hole
  • Critical Stop-Drilling Protocol

Inspect and Locate Tip: Clean all paint and grease. Use liquid fluorescent/dye penetrant or a 10X magnifying inspection glass to find the exact microscopic endpoint of the crack tip.

Drill Size Selection: Drill through the exact crack tip using a #30 ( 0.1285 " 0.1285" 0.1285" ) or #40 ( 0.0980 " 0.0980" 0.0980" ) drill bit (or 1 / 8 " 1/8" 1/8" bit per SRM specifications).

Post-Drill Inspection: Re-inspect the inside bore of the drilled hole with a magnifier or penetrant to confirm that the crack does not extend beyond the boundary of the hole. If crack remnants remain, re-drill with a larger bit.

Structural Doubler Requirement: Stop-drilling alone is only a temporary emergency measure or an initial step prior to installing an approved structural doubler patch.

4. Lap Patch vs. Flush Patch Structural Design LAP PATCH (Surface) vs. FLUSH PATCH (Aerodynamic/Pressurized):

  • [ LAP PATCH ] [ FLUSH PATCH ]
  • ┌───────────────────────────┐ ◄── Lap Patch ┌──────────────┐ ◄── Flush Filler Plug (Same Gauge)
  • │ (•) (•) (•) (•) │ (1 Gauge Thicker) ════╧══ ══╧════ ◄── Original Skin
  • ════╧═════╧═════╧═════╧═════╡ │ (•) (•) (•) │
  • ════════════════════════════╛ ◄── Original Skin └────────────────────┘ ◄── Internal Doubler
  • (1 Gauge Thicker)
  • Lap Patch (Surface Patch) Design Rules

Application: Unpressurized fuselages, secondary structure, and lower-speed surfaces where parasite aerodynamic drag is negligible.

Patch Thickness: Fabricated from the same alloy and temper as the original skin, and typically one standard gauge thicker (or equal thickness) to restore 100 % 100\% 100% original tensile strength.

Edge Chamfering: Outer perimeter chamfered at 45 ∘ 45^\circ 4 5 ∘ to minimize air drag and peeling forces.

Flush Patch (Aerodynamic Insertion) Design Rules

Application: High-speed aerodynamic surfaces, pressurized fuselage cabins, and control surface leading edges.

Three-Component Assembly:

Cutout: Damaged area is cut out cleanly into a circular, oval, or rectangular shape with rounded corners (minimum corner radius R = 0.50 " R = 0.50" R = 0.50" ) to prevent stress risers.

Internal Doubler: Installed behind the cutout. Must be fabricated from the same alloy/temper and one standard gauge thicker than the original skin (e.g., 0.040 " 0.040" 0.040" skin requires 0.050 " 0.050" 0.050" doubler).

Flush Filler Plug: Cut to match the exact shape of the cutout with a uniform 1 / 32 " 1/32" 1/32" to 1 / 16 " 1/16" 1/16" clearance gap around the perimeter. Must be the exact same gauge and alloy as the original skin.

Fastener Layout: Fasteners are arranged in multiple staggered rows (minimum 2 rows per side) to transfer full shear load around the cutout. Rivet Count per Side ( N ) = Length of Damage × Skin Thickness × Skin Tensile Strength Single Shear Strength of Selected Rivet \text{Rivet Count per Side } (N) = \frac{\text{Length of Damage } \times \text{Skin Thickness } \times \text{Skin Tensile Strength}}{\text{Single Shear Strength of Selected Rivet}} Rivet Count per Side ( N ) = Single Shear Strength of Selected Rivet Length of Damage × Skin Thickness × Skin Tensile Strength ​

5. Dimpling vs. Machine Countersinking

Flush riveting (using 100 ∘ 100^\circ 10 0 ∘ countersunk MS20426 rivets) requires creating a conical recess in the skin: MACHINE COUNTERSINKING vs. COIN DIMPLING:

  • [ MACHINE COUNTERSINKING (Thick Sheets >= 0.040") ]
  • ▼ 100° Cutter
  • ╲ ╱
  • ═══╲ ╱═══ ◄── Material Cut Away (Knife-edge avoided only if T >= 1.5 * Head Depth)
  • ═════ ═══
  • [ COIN DIMPLING (Thin Sheets < 0.040") ]
  • ▼ Male Die
  • ╲ ╱
  • ═══╲ ╱═══ ◄── Metal Formed & Coined (No Material Removed; 100% Strength Retained)
  • █ ◄── Female Coining Die

Parameter Machine Countersinking Coin / Radius Dimpling

Mechanism Rotating cutting tool removes metal to form 100 ∘ 100^\circ 10 0 ∘ recess. Male and female die set plastically deforms metal into 100 ∘ 100^\circ 10 0 ∘ cone without removing material.

Skin Thickness Rule Permitted only if sheet thickness T ≥ 1.5 × Rivet Head Depth T \ge 1.5 \times \text{Rivet Head Depth} T ≥ 1.5 × Rivet Head Depth (typically T ≥ 0.040 " T \ge 0.040" T ≥ 0.040" for 3 / 32 " 3/32" 3/32" rivets; T ≥ 0.050 " T \ge 0.050" T ≥ 0.050" for 1 / 8 " 1/8" 1/8" rivets). Mandatory for thin sheets ( T < 0.040 " T < 0.040" T < 0.040" ) where machine countersinking would create a knife-edge.

Structural Risk On thin sheet, creates a razor-sharp knife-edge in the hole, causing sheet cracking, hole elongation, and rivet pull-through. If dies misaligned, can cause radial cracking or sheet warping.

Hot Dimpling Not applicable. High-strength/brittle alloys (7075-T6, titanium, magnesium) are heated with resistance dies ( 300 ∘ F– 600 ∘ F 300^\circ\text{F}\text{--}600^\circ\text{F} 30 0 ∘ F – 60 0 ∘ F ) during dimpling to prevent cracking.

6. Corrosion Removal & Chemical Conversion Coating

Mechanical Cleaning: Strip paint and remove all corrosion products mechanically using non-metallic Scotch-Brite abrasive pads or aluminum oxide abrasive paper. Never use carbon steel brushes or steel wool , which embed microscopic iron particles and cause rapid galvanic corrosion.

Chemical Conversion (Alodining): Apply MIL-DTL-5541 (Alodine 1200 / Bonderite) chromate conversion coating to bare aluminum. Alodine chemically reacts with aluminum to form a microscopic, corrosion-resistant passive oxide film that provides an exceptional bonding base for primers.

Priming: Apply two-part polyamide epoxy zinc-chromate primer (MIL-PRF-23377) within the specified cure window before final rivet assembly and painting.