Study guide
3.2 Composite Damage Assessment, Repair Methods & Shop Safety
FAA Aviation Mechanic — Airframe AMA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Strategy
1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas
2 Chapter 2: Metallic Structures & Sheet Metal Repair
2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs
3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics
3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors
4 Chapter 4: Welding & Structural Fasteners
4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
5 Chapter 5: Flight Controls, Assembly & Rigging
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention
6 Chapter 6: Hydraulic & Pneumatic Power Systems
6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control
7 Chapter 7: Aircraft Landing Gear Systems
7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems
8 Chapter 8: Aircraft Fuel Systems
8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety
9 Chapter 9: Airframe Electrical Systems
9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting
10 Chapter 10: Cabin Atmosphere & Environmental Control
10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators
11 Chapter 11: Aircraft Instrument Systems
11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections
12 Chapter 12: Communication, Navigation & Warning Systems
12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning
13 Chapter 13: Ice, Rain & Fire Protection Systems
13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture
14 Chapter 14: Airframe Inspection & Maintenance Regulations
14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT
15 Chapter 15: Rotorcraft Fundamentals
15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety
16 Chapter 16: Water & Waste Systems
16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety
3.2 Composite Damage Assessment, Repair Methods & Shop Safety
Key Takeaways Explain This Topic AI
The coin tap test is a reliable preliminary acoustic NDT method: sound laminate produces a clear metallic ring, while delaminations or disbonds produce a dull, dead thud.
Structural flush repairs require a scarf taper ratio of at least 50:1 (taper length to skin thickness) to restore full tensile and shear load capabilities.
Replacement repair plies must strictly replicate the original laminate's material, ply count, thickness, and warp clock orientation (0°, ±45°, 90°).
A standard vacuum bagging stack utilizes peel ply, perforated release film, bleeder cloth, solid separator, and breather cloth to consolidate plies under 22 to 28 inHg of vacuum.
Hot-bond cure cycles must control heat ramp-up, soak dwell, and cool-down rates under continuous vacuum until temperature drops below 140°F (60°C) to prevent thermal shock and warpage.
Last updated: August 2026
Composite Damage Assessment, Repair Methods & Shop Safety
FAA Airframe Mechanic Standard: Composite structural maintenance requires rigorous damage evaluation, precise non-destructive inspection (NDI), calibrated scarfing geometry, controlled vacuum consolidation, and thermal cure cycle management in accordance with 14 CFR Part 43 , FAA-H-8083-31A , and AC 43.13-1B Chapter 3 .
1. Composite Damage Classifications
Damage in composite aircraft structures is classified by its physical mechanism and depth:
Delamination: Separation of adjacent reinforcing fiber plies within a solid laminate or sandwich facesheet. Often caused by interlaminar shear stress or low-velocity impact.
Disbond (Debond): Separation between two bonded structural elements, such as the composite facesheet lifting off the honeycomb core or a bonded doubler separating from a skin.
Fiber Breakout / Fracture: Rupture of reinforcing fibers due to tensile overstress, puncture, or lightning strike burning.
Core Crush / Buckling: Compressive collapse of honeycomb cell walls or crushed foam core resulting from blunt impact or high concentrated surface loads.
Moisture Ingress: Water entering damaged sandwich panels through micro-cracks or pinholes. At high cruising altitudes, water freezes, expands, and tears the facesheet away from the core; at high speeds, trapped water causes core cell rupture during rapid cabin depressurization.
Barely Visible Impact Damage (BVID): Subsurface internal damage (delamination, core shear failure) caused by low-velocity impact (dropped tools, hail, runway debris) that leaves little or no visible indentation on the outer mold line (OML).
2. Non-Destructive Inspection (NDI/NDT) Techniques
Before undertaking any repair, an AMT must establish the full geographic boundary of structural damage using approved NDI methods. +-------------------------------------------------------------------------+
- | COMPOSITE NON-DESTRUCTIVE INSPECTION (NDI) |
- +-------------------+----------------------------+------------------------+
- | Tap Testing | Ultrasonic Inspection | Radiography (X-Ray) |
- | - Metallic ring | - Pulse-Echo / Thru-Trans | - Detects core crush |
- | = Sound | - Precise depth & boundary | - Trapped water in |
- | - Dull thud | - Standard shop NDI | honeycomb cells |
- | = Delamination | | - Heavy safety controls|
- +-------------------+----------------------------+------------------------+
- A. Tap Testing (Acoustic Ring)
Procedure: Lightly tapping the composite surface along a grid using a specialized composite tap hammer, lightweight plastic rod, or a smooth steel coin (e.g., a quarter).
Acoustic Signature:
Sound, well-bonded structure: Produces a sharp, crisp, high-pitched metallic ringing sound as acoustic energy transfers cleanly into the underlying structure.
Delaminated / Disbonded structure: Produces a flat, hollow, dull "thud" sound because the internal air gap prevents sound propagation.
Limitations: Only effective for detecting shallow defects within the outer 2 to 3 plies or skin-to-core disbonds in thin skins ( < 0.080 in < 0.080\text{ in} < 0.080 in ). Cannot reliably detect deep internal delaminations in thick laminates.
B. Ultrasonic Inspection
Pulse-Echo: A single piezoelectric transducer transmits high-frequency sound waves ( 1 to 10 MHz 1\text{ to }10\text{ MHz} 1 to 10 MHz ) into the laminate and receives reflected echoes. An internal delamination reflects sound energy back prematurely, displaying a distinct flaw signal on the A-scan display and establishing exact defect depth.
Through-Transmission: Requires two aligned transducers on opposite sides of the part (one transmitting, one receiving). A defect attenuates or blocks the sound beam.
C. Radiography (X-Ray)
High-energy X-rays pass through the composite component onto radiographic film or digital detector plates.
Primary Application: Superior for identifying water ingress in honeycomb core cells , crushed or distorted core cell ribbons, sheared internal fasteners, and foreign object debris (FOD). Less effective for planar delaminations parallel to the X-ray beam.
D. Thermography (Infrared NDI) & Laser Shearography
Flash Thermography: Heat lamps apply a brief thermal pulse to the surface; an infrared camera monitors surface temperature decay. Subsurface voids and disbonds impede heat transfer, appearing as warm localized hotspots.
Laser Shearography: Illuminates the surface with coherent laser light while applying a slight mechanical or vacuum stress. An interferometer compares speckle patterns to detect minute out-of-plane surface gradient changes caused by subsurface delaminations.
NDI Method Primary Flaws Detected Portability / Cost Limitations
Coin Tap Test Near-surface delaminations & skin-to-core disbonds Excellent / Very Low Shallow depth only; subjective to operator ear
Ultrasonic Pulse-Echo Laminate delaminations, voids, thickness High / Moderate Requires couplant gel; slow area scanning
X-Ray Radiography Trapped core moisture, crushed core, sheared pins Low / High Radiation hazard; poor detection of flat delaminations
Flash Thermography Water ingress, near-surface disbonds, voids Moderate / High Depth limited; sensitive to surface emissivity
Laser Shearography Delaminations, disbonds in large panels Moderate / High Requires active vacuum/thermal excitation
3. Structural Repair Methodologies: Scarf vs. Step-Sanding
When structural composite damage exceeds allowable limits, the damaged plies must be machined away and replaced with an engineered repair patch. SCARF REPAIR PROFILE (50:1 Taper)
<--------------------------------- Scarf Width --------------------------------->
- Original Laminate Original Laminate
- ======-----------------------------------------------------------------======
- \ /
- \ /
- \================== Replacement Plies =====================/
- \________________________________________________________/
- A. Scarf (Tapered) Repair Geometry
In a scarf repair, damaged material is machined out in a continuous uniform bevel angle. The standard structural taper ratio specified in AC 43.13-1B and most aircraft Structural Repair Manuals (SRMs) is 50:1 (taper length to laminate thickness): Scarf Taper Ratio = Scarf Length per Side Laminate Thickness = 50 1 \text{Scarf Taper Ratio} = \frac{\text{Scarf Length per Side}}{\text{Laminate Thickness}} = \frac{50}{1} Scarf Taper Ratio = Laminate Thickness Scarf Length per Side = 1 50
Example: For a solid carbon fiber skin with a thickness of 0.060 in 0.060\text{ in} 0.060 in , the scarf taper must extend: Taper Length = 0.060 in × 50 = 3.0 inches per side \text{Taper Length} = 0.060\text{ in} \times 50 = 3.0\text{ inches per side} Taper Length = 0.060 in × 50 = 3.0 inches per side
Non-structural or secondary skins may permit a steeper 30:1 taper ratio, but critical primary flight structures strictly mandate 50:1 or greater.
B. Step-Sanded Repair
In step-sanding, each ply is carefully ground away to form a series of discrete, stepped concentric rings. Each step is typically machined 0.5 inches 0.5\text{ inches} 0.5 inches ( 12.7 mm 12.7\text{ mm} 12.7 mm ) wide per ply . Step repairs require extreme precision to avoid cutting into underlying undamaged plies.
C. Ply Orientation & Ply Schedule Matching
During structural repair:
Every replacement ply must match the original ply in fiber material (carbon, fiberglass, Kevlar), weave style , and areal weight .
Warp Clock Alignment: Each replacement ply must align precisely with the original ply's orientation ( 0 ∘ , + 45 ∘ , − 45 ∘ , 90 ∘ 0^\circ, +45^\circ, -45^\circ, 90^\circ 0 ∘ , + 4 5 ∘ , − 4 5 ∘ , 9 0 ∘ ). Altering ply orientation drastically alters torsional and bending stiffness.
Sacrifice / Cover Ply: An extra cover ply (usually fine-weave fiberglass or carbon extending 0.5 to 1.0 inch 0.5\text{ to }1.0\text{ inch} 0.5 to 1.0 inch beyond the scarf perimeter) is placed over the entire repair to protect against aerodynamic erosion and permit flush sanding.
D. Honeycomb Core Repairs
Potted Repair: For small puncture damage ( < 1.0 inch < 1.0\text{ inch} < 1.0 inch diameter) with no structural core crush, the damaged cell area is cleaned, dried, and injected with an epoxy resin filled with glass microballoons (syntactic foam).
Core Replacement Plug: For damage exceeding 1.0 inch 1.0\text{ inch} 1.0 inch , the damaged core is routed out cleanly. A matching core plug (same material, cell size, density, and ribbon direction) is inserted and bonded to the surrounding core walls using an expanding structural foaming adhesive film .
4. Vacuum Bagging Assembly & Consumables Stack
Vacuum bagging consolidates laminate plies, removes trapped air and volatile gases, and extracts excess matrix resin to achieve an optimum fiber-to-resin ratio (typically 55 % to 60 % 55\%\text{ to }60\% 55% to 60% fiber by volume ). +-------------------------------------------------------------------------+
- | VACUUM BAGGING STACK (Top to Bottom) |
- +-------------------------------------------------------------------------+
- | [1] Vacuum Bag Film (Nylon / Polyamide film; sealed with mastic tape) |
- | [2] Breather Cloth (Non-woven polyester; continuous vacuum pathway) |
- | [3] Solid Separator Film (Non-porous release film; isolates resin) |
- | [4] Bleeder Cloth (Absorbent felt; absorbs excess resin) |
- | [5] Perforated Release Film (Porous fluoropolymer; regulates bleeding) |
- | [6] Peel Ply (Textured nylon/polyester; creates clean bonding surface) |
- | [7] Composite Repair Laminate + Thermocouples |
- | [8] Tool / Aircraft Mold Line Skin |
- +-------------------------------------------------------------------------+
- Layer-by-Layer Components & Functions
Peel Ply (Release Ply): A tightly woven nylon or polyester fabric laid directly against the wet laminate. It allows resin and air to pass through and is peeled off after cure, leaving a clean, textured, contaminant-free surface ready for painting or secondary bonding without mechanical sanding.
Perforated (Porous) Release Film: A fluoropolymer (Teflon/ETFE) film with calibrated micro-perforations. It allows volatile gases and controlled quantities of excess resin to escape into the bleeder while preventing the bleeder cloth from sticking to the laminate.
Bleeder Cloth: An open, absorbent non-woven synthetic felt that soaks up excess resin bled from the laminate.
Solid (Non-Porous) Separator Film: A solid plastic barrier placed over the bleeder cloth to prevent liquid resin from migrating into the breather cloth.
Breather Cloth: A thick, fluffy non-woven polyester mat that covers the entire repair area. It provides a continuous, open path for air evacuation under the vacuum bag, preventing dead spots.
Thermocouples (J or K Type): Calibrated temperature-sensing wire junctions taped around the repair perimeter and under the heat blanket to provide real-time thermal feedback to the hot bonder.
Vacuum Bag & Mastic Sealant Tape: High-temperature flexible nylon film sealed around the repair perimeter using high-tack synthetic rubber mastic tape (butyl sealant tape).
Vacuum Pressure & Leak Checking
Operating Vacuum: Structural hot-bond repairs typically require 22 to 28 inches of Mercury (inHg) 22\text{ to }28\text{ inches of Mercury (inHg)} 22 to 28 inches of Mercury (inHg) (equivalent to ≈ 10.8 to 13.7 psi \approx 10.8\text{ to }13.7\text{ psi} ≈ 10.8 to 13.7 psi consolidating force).
Vacuum Drop Test (Leak Check): After reaching full vacuum, the vacuum source is isolated. The bag must not lose more than 1.0 inHg 1.0\text{ inHg} 1.0 inHg of vacuum pressure over a 5-minute period . Any excessive leak must be located and sealed with mastic tape before initiating thermal cure.
5. Thermal Cure Cycles & Hot Bonder Operation
Structural repairs using 250 ∘ F 250^\circ\text{F} 25 0 ∘ F or 350 ∘ F 350^\circ\text{F} 35 0 ∘ F curing prepregs or film adhesives utilize microprocessor-controlled hot bonders paired with flexible silicone heating blankets. Temp (°F)
- ^
- | Soak / Dwell Period
- | +---------------------------+
- 350°| / \
- | / \
- | Ramp-Up / \ Cool-Down Rate
- | 1-5°F/min / \ < 5°F/min
- | / \
- | / \
- 70°+------------+-----------------------------------------+--------> Time (min)
- |<-- Heat -->|<---------- Hold at Temp --------------->|<- Cool ->|
- The Three Critical Cure Stages
Ramp-Up Rate: Heating must occur at a controlled rate, typically 1 ∘ F to 5 ∘ F 1^\circ\text{F}\text{ to }5^\circ\text{F} 1 ∘ F to 5 ∘ F per minute . Heating too fast causes thermal shock, uneven resin viscosity, and traps volatiles before the resin can flow.
Soak / Dwell Temperature: The bonder holds the setpoint temperature (e.g., 250 ∘ F ± 10 ∘ F 250^\circ\text{F} \pm 10^\circ\text{F} 25 0 ∘ F ± 1 0 ∘ F or 350 ∘ F ± 10 ∘ F 350^\circ\text{F} \pm 10^\circ\text{F} 35 0 ∘ F ± 1 0 ∘ F ) for the manufacturer-mandated soak duration (typically 60 to 120 minutes 60\text{ to }120\text{ minutes} 60 to 120 minutes ) to complete polymer cross-linking.
Cool-Down Rate: Controlled cooling must not exceed 5 ∘ F 5^\circ\text{F} 5 ∘ F per minute . Continuous vacuum pressure must be maintained throughout cooling until the repair surface drops below 140 ∘ F 140^\circ\text{F} 14 0 ∘ F ( 60 ∘ C 60^\circ\text{C} 6 0 ∘ C ) . Releasing vacuum or removing heat blankets above 140 ∘ F 140^\circ\text{F} 14 0 ∘ F induces internal residual stress, micro-cracking, and part warpage.
6. Shop Safety, PPE & Chemical Hazards
Respirable Particulates: Machining, trimming, and sanding carbon fiber and fiberglass generates fine airborne particulates that cause severe mechanical irritation to lung tissue. AMTs must operate in HEPA-filtered downdraft sanding booths and wear a NIOSH-approved N95 or P100 half-face particulate respirator and sealed safety goggles.
Epoxy & Hardener Toxicity: Amine-based epoxy curing agents are potent chemical sensitizers. Repeated skin contact causes severe allergic contact dermatitis and permanent respiratory sensitization. AMTs must wear disposable chemical-resistant nitrile gloves (latex gloves are permeable to epoxy amines and solvents) and barrier creams.