Study guide
15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection
FAA Aviation Mechanic — Airframe AMA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Strategy
1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas
2 Chapter 2: Metallic Structures & Sheet Metal Repair
2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs
3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics
3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors
4 Chapter 4: Welding & Structural Fasteners
4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
5 Chapter 5: Flight Controls, Assembly & Rigging
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention
6 Chapter 6: Hydraulic & Pneumatic Power Systems
6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control
7 Chapter 7: Aircraft Landing Gear Systems
7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems
8 Chapter 8: Aircraft Fuel Systems
8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety
9 Chapter 9: Airframe Electrical Systems
9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting
10 Chapter 10: Cabin Atmosphere & Environmental Control
10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators
11 Chapter 11: Aircraft Instrument Systems
11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections
12 Chapter 12: Communication, Navigation & Warning Systems
12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning
13 Chapter 13: Ice, Rain & Fire Protection Systems
13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture
14 Chapter 14: Airframe Inspection & Maintenance Regulations
14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT
15 Chapter 15: Rotorcraft Fundamentals
15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety
16 Chapter 16: Water & Waste Systems
16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety
15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection
Key Takeaways Explain This Topic AI
Main rotor blades are matched, serialized, life-limited assemblies; a blade is normally replaced rather than repaired, and the manufacturer's structural repair data defines the only allowable damage limits.
A metal rotor blade's hollow spar may carry a blade inspection method (BIM) pressure indicator; a color change signals a spar crack and grounds the blade.
The main transmission reduces engine speed to rotor speed, mounts the freewheeling unit and rotor brake, and drives accessories plus the tail rotor drive shaft.
Transmission and gearbox chip detectors, oil temperature and pressure indication, and magnetic plug inspection are the primary early warning of drive system distress.
Skid landing gear is inspected for spread or narrowed cross tubes as evidence of a hard landing, and replaceable skid shoes are the designed wear item on the bottom of each skid tube.
Last updated: August 2026
15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection
Quick Summary: ACS Subject II.N asks the mechanic to understand rotor blade functions and construction (K7) , transmissions (K3) , drive system vibrations and inspection (K9) , and helicopter skid shoe and tube inspection (K6) . This section covers the hardware itself: how a rotor blade is built and condemned, how power gets from the engine to both rotors, how gearbox distress announces itself, and what a hard landing does to skid gear.
1. Main Rotor Blade Construction (AM.II.N.K7)
A rotor blade is a rotating wing operating at near-supersonic tip speed while changing pitch several times per second. Two construction families dominate:
Metal blades are built around a hollow extruded aluminum or steel spar that carries essentially all of the centrifugal and bending load. Aft of the spar, formed skins are bonded over a honeycomb or foam core to form the afterbody and trailing edge. A leading edge abrasion strip — stainless steel, titanium, or nickel — protects the high-erosion region and is a routine replacement item.
Composite blades use unidirectional glass or carbon spar packs with fabric skins over a foam or honeycomb core. They tolerate damage better, resist fatigue cracking, and can be built with non-linear twist and tapered tips that a metal extrusion cannot match.
Blade Inspection Method (BIM) Indicators
Some metal blades pressurize the hollow spar with dry nitrogen or simply seal it, then fit a BIM indicator at the root. If a spar crack lets the pressure change, the indicator changes color or position.
Important
A BIM indication is not a discrepancy to "monitor." It is evidence of a possible spar crack , and the blade is removed from service per the maintenance manual. Treat it the same way you treat a fuel tank found with water — the answer is action, not observation.
Blade Damage and Repairability
Rotor blades are matched, serialized, life-limited components. Blades are frequently supplied and installed as a matched set , and the manufacturer's data — not AC 43.13-1B — defines the allowable damage limits. General airframe repair practices do not authorize a rotor blade repair.
Finding Typical Disposition
Nick or scratch within published limits in a non-critical zone Blend out per the maintenance manual, within the specified depth and blend ratio
Any damage to the spar Blade removed from service
Skin-to-core disbond (found by tap test or instrumented NDT) Repair only per manufacturer data, or blade removed
- BIM indication Blade removed from service
- Trim tab damaged or bent out of limits Re-set per track and balance data — see section 15.3
- Lightning strike or overtorque event Special inspection per the maintenance manual
Tail rotor blades follow the same philosophy and add a hazard: the tail rotor operates in the debris field kicked up by the main rotor and is a frequent site of erosion and FOD damage.
2. The Main Transmission (AM.II.N.K3) ENGINE ──► FREEWHEELING UNIT ──► MAIN TRANSMISSION ──► MAST ──► MAIN ROTOR
- │ │ │
- │ │ └──► ACCESSORIES (hyd pump, generator,
- │ │ tach generator)
- │ └─────► ROTOR BRAKE (where installed)
- │
- └────────► TAIL ROTOR DRIVE SHAFT
- │ (hanger bearings,
- │ flexible couplings)
- ▼
- INTERMEDIATE GEARBOX (42°)
- │
- ▼
- TAIL ROTOR GEARBOX (90°)
- │
- ▼
- TAIL ROTOR
The transmission performs four jobs at once:
Speed reduction. Turbine output can exceed 20,000 RPM while a main rotor turns in the hundreds of RPM. The transmission provides that large reduction through planetary and bevel gear stages.
Torque path and structural support. The transmission carries main rotor lift and moment loads into the airframe through its mounts and lift links.
Accessory and tail rotor drive. It drives hydraulic pumps, generators, tachometer generators, and the tail rotor drive shaft.
Rotor brake mounting. Where installed, the rotor brake stops the rotor after shutdown, and is used only within the RPM limits published in the flight manual.
The tail rotor drive shaft runs the length of the tailboom in segments, supported by hanger bearings and joined by flexible couplings (disc packs, elastomeric couplings, or splined joints) that tolerate airframe flexing and slight misalignment. An intermediate gearbox typically turns the drive through about 42 degrees at the base of the vertical fin, and the tail rotor gearbox turns it the final 90 degrees and provides the final reduction.
3. Drive System Condition Monitoring (AM.II.N.K9)
Gearboxes fail slowly and announce themselves in metal and heat. The mechanic's toolkit:
Monitoring Method What It Tells You
Magnetic chip detector / chip light Ferrous particles in the oil. Fine fuzz can be normal wear; chips, slivers, or flakes indicate a failing gear or bearing.
Magnetic drain plug inspection Same evidence, captured at oil change. Photograph and characterize the debris before cleaning.
Oil temperature and pressure indication Rising temperature at constant power suggests bearing distress or an oil supply problem.
Oil analysis (SOAP) Trends wear metals over time and catches distress before it reaches the chip detector.
Sight glass level and oil condition Overheated, dark, or emulsified oil is itself a discrepancy.
Vibration monitoring / HUMS Trends drive shaft and gearbox signatures — see section 15.3.
Important
A chip light is a maintenance event, not a nuisance. The maintenance manual governs, but the universal rule is: inspect the debris, identify it, and determine the source. Wiping the plug and resetting the light without characterizing the material is exactly the decision that turns a gearbox inspection into a gearbox failure.
Drive shaft vibration has its own diagnostic vocabulary. A drive shaft that is out of balance, bent, or running on a failing hanger bearing produces a higher-frequency vibration than the main rotor does, felt through the airframe structure rather than through the controls. Hanger bearings are checked for roughness, play, and security; couplings are checked for cracked discs, elongated bolt holes, and loss of grease or elastomer.
4. Skid Landing Gear: Cross Tubes and Skid Shoes (AM.II.N.K6)
Many helicopters use fixed skid gear : two skid tubes joined to the fuselage by forward and aft cross tubes that flex to absorb landing loads. There are no oleo struts, so the cross tubes themselves are the shock absorbers — and they are the diagnostic.
Hard landing evidence. A hard vertical landing spreads the skid gear: the cross tubes deform, the skids move farther apart, and the fuselage sits lower. Manufacturers publish a skid gear width or height dimension that is measured during inspection. A measurement outside limits means the cross tubes have taken a permanent set and must be replaced, and it also triggers the hard landing special inspection of the mast, transmission mounts, and airframe structure. In cold weather operations the opposite can occur: repeated high-load cycles or a specific failure mode can leave the skids narrowed . Either deviation from the published dimension is a rejection.
Skid shoes (also called wear shoes or abrasion shoes) are replaceable steel or hard-alloy strips fitted to the bottom of each skid tube. They exist to be consumed — ground contact during running landings, sliding, and ground handling wears the shoe rather than the structural skid tube. The inspection standard is straightforward and is a favorite oral question:
Measure remaining shoe thickness against the published wear limit.
Wear through the shoe into the skid tube itself condemns the skid tube , not just the shoe. That is why the shoe is replaced well before it is consumed.
Check shoe attachment security and the condition of the fasteners or bonding.
Inspect the skid tube for cracks, dents, corrosion, and abrasion, particularly at the cross tube saddle clamps where fretting and hidden corrosion concentrate.
Ground handling wheels, when installed, jack against the skid gear to lift the skids for towing. They are removed before flight, and their attachment points are inspected for damage caused by towing loads.