Study guide

15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

FAA Aviation Mechanic — Airframe AMA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Strategy

1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas

2 Chapter 2: Metallic Structures & Sheet Metal Repair

2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs

3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics

3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors

4 Chapter 4: Welding & Structural Fasteners

4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware

5 Chapter 5: Flight Controls, Assembly & Rigging

5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention

6 Chapter 6: Hydraulic & Pneumatic Power Systems

6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control

7 Chapter 7: Aircraft Landing Gear Systems

7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems

8 Chapter 8: Aircraft Fuel Systems

8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety

9 Chapter 9: Airframe Electrical Systems

9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting

10 Chapter 10: Cabin Atmosphere & Environmental Control

10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators

11 Chapter 11: Aircraft Instrument Systems

11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections

12 Chapter 12: Communication, Navigation & Warning Systems

12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning

13 Chapter 13: Ice, Rain & Fire Protection Systems

13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture

14 Chapter 14: Airframe Inspection & Maintenance Regulations

14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT

15 Chapter 15: Rotorcraft Fundamentals

15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

16 Chapter 16: Water & Waste Systems

16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety

15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

Key Takeaways Explain This Topic AI

A vertical vibration indicates unequal lift between blades, an out-of-track condition corrected by adjusting pitch change link length or bending trim tabs.

A lateral vibration indicates unequal mass distribution in the rotor disc, a spanwise out-of-balance condition corrected with hub or blade weights.

Low-frequency vibrations originate in the main rotor, medium-frequency vibrations in drive shafts and cooling fans, and high-frequency vibrations in the tail rotor and engine accessories.

Rotor track is verified with tip targets and a strobe or with an electronic track and balance analyzer; ACS skill elements only require locating and explaining the manufacturer's procedures.

Personnel approach a helicopter from the front within the pilot's field of vision, never from the rear near the tail rotor, and from the downslope side on uneven terrain.

Last updated: August 2026

15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety

Quick Summary: Every ACS skill element in Subject II.N is a locate and explain task: locate rotor system components (S1) , locate blade track and balance procedures (S2) , locate and explain helicopter control rigging (S3) , and locate and explain rotor track and balance (S4) . The FAA is not asking for type-specific numbers. It is asking whether you understand what track and balance is , what each vibration symptom means , and how to work around a running helicopter without being killed by it.

1. Rigging a Rotary-Wing Aircraft (AM.II.N.K4)

Fixed-wing rigging sets control surface travel against fixed stops. Rotary-wing rigging sets blade pitch angles and the relationship between the controls, the swashplate, and every blade , and it must be done in a specific order.

The measurement tools are different too. Where an airplane uses a protractor on a control surface, a helicopter uses a universal propeller protractor or a blade pitch gauge on the blade itself, referenced to a level rotor head. A typical rigging sequence, always per the manufacturer's manual:

Level the aircraft and secure the rotor. Rigging is done with the rotor stopped and the blades in specified index positions.

Set control lengths to nominal. Push-pull tubes, bellcranks, and servo inputs are set to their published dimensions, and each rod end is checked so that the witness hole is covered and the minimum thread engagement is met.

Rig the collective. Verify minimum and maximum blade pitch at the full-down and full-up collective stops.

Rig the cyclic. Verify swashplate tilt and the resulting blade pitch at each azimuth against the published travel limits.

Rig the anti-torque pedals. Set tail rotor pitch range at full left and full right pedal.

Set all blades to the same pitch at a reference collective setting, which is the static track starting point.

Ground run and adjust dynamically — that is track and balance.

Important

Static rigging gets all blades to the same commanded pitch. It does not make them fly through the same path, because blades differ slightly in chord profile, twist, and mass. Closing that gap is the entire purpose of dynamic track and balance .

2. Track versus Balance (AM.II.N.K8)

This distinction is the single highest-value item in the whole rotorcraft area, and it has a clean two-line rule. ┌───────────────────────────────────────────────────────────────────────────┐

  • │ VERTICAL vibration ──► unequal LIFT ──► OUT OF TRACK │
  • │ Fix: pitch change link length / trim tabs │
  • ├───────────────────────────────────────────────────────────────────────────┤
  • │ LATERAL vibration ──► unequal MASS ──► OUT OF BALANCE │
  • │ Fix: spanwise / chordwise balance weights │
  • └───────────────────────────────────────────────────────────────────────────┘

Track is whether all blade tips pass through the same tip-path plane at a given point in the rotation. A blade that flies high or low is producing more or less lift than its neighbors — from a slight chord profile difference, a mis-set pitch change link, or a bent trim tab. The symptom felt in the airframe is a vertical (one-per-revolution) vibration.

Balance is whether mass is distributed evenly around the disc. Manufacturing tolerances, paint, repairs, moisture absorbed by a blade, and erosion all shift blade mass. The symptom is a lateral vibration.

The two interact, which is why order matters: correct track first, then balance , and re-check track afterward, because a track change alters the lateral reading.

Corrections

Correction What It Changes Used For

Pitch change link lengthened or shortened Blade pitch angle across the whole revolution Track, usually the dominant correction at hover

Trim tab bent up or down Blade lift at a given pitch angle (tab down increases lift and raises the blade) Track, particularly differences that appear only at forward flight speeds

  • Spanwise weights (hub or blade tip) Mass distribution along the blade span Lateral balance
  • Chordwise weights Mass distribution fore and aft of the pitch axis Chordwise balance, per manufacturer data

A practical consequence worth knowing: a track split that shows up at hover is normally chased with the pitch change link , while a split that only appears at forward flight airspeeds is normally chased with the trim tab . That is why track and balance readings are recorded at several specified flight conditions rather than at one.

3. Measuring Track and Balance (AM.II.N.S2, S4)

Legacy methods are still tested because they explain the concept. In the flag or pole method , a different colored marker is applied to each blade tip and a target is brought into the tip path so each blade marks it; blades marking at different heights are out of track. Grease pencil and reflector variants work the same way.

Current practice uses an electronic track and balance analyzer (Chadwick-Helmuth Vibrex, ACES Viper or Cobra, Helitune, and similar). The installation is consistent across manufacturers:

A magnetic pickup on the stationary swashplate with an interrupter on the rotating swashplate generates one pulse per revolution, giving the analyzer the phase reference — the clock angle of the vibration.

Reflective tip targets on the blade tips are illuminated by a strobe triggered from that pulse, freezing the blades so track can be read directly.

A vertical accelerometer or velocimeter measures out-of-track vibration; a lateral sensor measures out-of-balance vibration.

The analyzer reports amplitude in inches per second (IPS) with a clock angle. The technician plots that point on the type-specific balance chart , which converts it into a specific correction — so many grams of weight at a given position, or so many flats of pitch link adjustment.

Modern rotorcraft may carry HUMS (Health and Usage Monitoring Systems) that trend these same vibration signatures continuously and flag a rising one-per-rev before the crew notices it.

4. Diagnosing Vibration by Frequency (AM.II.N.K9)

Because every rotating component turns at its own speed, frequency identifies the culprit.

Frequency Band Source Typical Causes

Low frequency (1/rev and 2/rev of the main rotor) Main rotor Out of track, out of balance, worn pitch change link bearings, worn mixing levers, defective dampers

Medium frequency Drive train and accessories Tail rotor drive shaft imbalance or bend, failing hanger bearings, cooling fan imbalance, engine mounts

High frequency Tail rotor and engine Tail rotor out of track or balance, tail rotor gearbox, engine accessories, high-speed shafting

A reliable field heuristic: if you can count it, it is the main rotor. Low-frequency vibrations are slow enough to feel individually and come through the controls and airframe as a beat. High-frequency vibrations are felt as a buzz or numbness — most often in the pedals, which points directly at the tail rotor.

5. Ground Safety and Functional Testing (AM.II.N.R1–R4)

The ACS devotes four of its nine risk management elements in this Subject to ground operations, which tells you how the FAA weights it.

Approaching a running helicopter. Per FAA guidance:

Approach from the front, within the pilot's field of vision , and only after receiving the pilot's acknowledgment. Never approach until signaled.

Never approach from the rear. The tail rotor is effectively invisible when turning and is the most common cause of ground fatalities around helicopters.

Stay low and carry nothing overhead. Main rotor blades droop and flex, and blade height above ground varies with rotor RPM, coning, and gusts.

On uneven terrain, approach and depart from the downslope (lower) side , which is where rotor clearance is greatest. Approaching from the upslope side puts the blades near head height.

If blowing dust or grit reduces visibility, stop, crouch, and wait for the pilot or for conditions to improve rather than continuing blind.

Maintenance ground runs and functional tests. A rotor turning at operating RPM stores an enormous amount of energy:

Establish and brief a danger area; keep non-essential personnel outside it.

Secure all tools, panels, cowlings, and paperwork. FOD in a rotor system is not survivable equipment damage.

Verify that all fasteners, rod ends, and safetying disturbed during rigging are complete and secured before the first turn, and check that witness holes are covered and jam nuts are tight.

Ensure blade tie-downs are removed, ground handling wheels are removed, and the aircraft is clear of obstructions through the full disc.

Use the rotor brake only within its published RPM limits.

Never make an adjustment on a rotor system until it has come to a complete stop , and follow the manufacturer's procedure for securing the blades against wind.