Study guide
4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
FAA Aviation Mechanic — Airframe AMA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Strategy
1.1 Exam Structure, Eligibility & 14 CFR Part 65 Requirements 1.2 Study Strategy, Blueprint Weighting & Core Formulas
2 Chapter 2: Metallic Structures & Sheet Metal Repair
2.1 Aluminum Alloys, Heat Treatment & Rivet Identification 2.2 Rivet Layout, Edge Distance, Spacing & Driving Standards 2.3 Sheet Metal Layout: Bend Allowance, Setback & Forming 2.4 Sheet Metal Inspection, Damage Evaluation & Flush/Lap Repairs
3 Chapter 3: Non-Metallic Structures: Composites, Wood, Fabric & Transparent Plastics
3.1 Advanced Composites: Fiber Types, Resin Matrices & Core Materials 3.2 Composite Damage Assessment, Repair Methods & Shop Safety 3.3 Aircraft Wood Structures: Defects, Allowable Repairs & Gluing 3.4 Aircraft Fabric Covering, Inspection & Doping/Finishing Processes 3.5 Transparent Plastics, Windows, Windshields & Cabin Interiors
4 Chapter 4: Welding & Structural Fasteners
4.1 Oxyacetylene & Electric Arc Welding Principles for Aviation 4.2 Tubular Steel Fuselage Inspection, Defect Types & Approved Repairs 4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
5 Chapter 5: Flight Controls, Assembly & Rigging
5.1 Primary and Secondary Flight Control Surfaces & Aerodynamics 5.2 Control Cables, Tensiometers & Temperature-Compensated Rigging 5.3 Turnbuckles, Cable Safetying, Pulleys & Fairleads 5.4 Control Surface Travel, Mass Balancing & Flutter Prevention
6 Chapter 6: Hydraulic & Pneumatic Power Systems
6.1 Hydraulic Fluids, Seal Materials & Contamination Control 6.2 Hydraulic Reservoirs, Power Pumps & Accumulators 6.3 Hydraulic Valves: Pressure, Flow & Directional Control 6.4 High-Pressure Pneumatic Systems, Air Compressors & Moisture Control
7 Chapter 7: Aircraft Landing Gear Systems
7.1 Oleo Shock Struts: Servicing, Air/Oil Charging & Metering Pins 7.2 Retraction Mechanisms, Down-Locks, Alignment & Torque Links 7.3 Aircraft Brakes, Multi-Disc Systems & Anti-Skid Operations 7.4 Aircraft Tires, Wheels, Bearings & Emergency Extension Systems
8 Chapter 8: Aircraft Fuel Systems
8.1 Fuel Tank Types: Rigid, Bladder & Integral (Wet Wing) Tanks 8.2 Fuel System Plumbing: Boost Pumps, Selector Valves & Filtration 8.3 Crossfeed, Fuel Jettison, Fuel Quantity Indication & Probes 8.4 Fuel System Maintenance, Defueling & Tank Confined-Space Safety
9 Chapter 9: Airframe Electrical Systems
9.1 AC & DC Power Generation: Alternators, Inverters & TRUs 9.2 Aircraft Electrical Distribution, Bus Architecture & Circuit Protection 9.3 Aircraft Wire Selection (MIL-W-5086 / MIL-W-22759), Sizing & Bundling 9.4 Bonding, Grounding, Static Dischargers & Electrical Troubleshooting
10 Chapter 10: Cabin Atmosphere & Environmental Control
10.1 Vapor-Cycle & Air-Cycle Machine (ACM) Refrigeration Systems 10.2 Cabin Pressurization: Outflow Valves, Safety Valves & Regulators 10.3 Heating Systems: Combustion Heaters, Exhaust Muffs & Bleed Air 10.4 Aircraft Oxygen Systems: Continuous-Flow, Diluter-Demand & Generators
11 Chapter 11: Aircraft Instrument Systems
11.1 Pitot-Static Systems: Altimeter, VSI, Airspeed & Error Diagnosis 11.2 Gyroscopic Flight Instruments: Rigidity, Precession & Power Sources 11.3 Engine & System Instruments: Bourdon Tubes, Synchros & EICAS 11.4 Instrument Installation, Magnetic Compass Swing & Regulatory Inspections
12 Chapter 12: Communication, Navigation & Warning Systems
12.1 VHF/HF Communications, Antennas & Coaxial Cable Installation 12.2 Navigation Systems: VOR, ILS, DME, ADF, GPS & Weather Radar 12.3 Transponders, Altitude Encoders & Emergency Locator Transmitters 12.4 Position & Warning Systems: Landing Gear Horns, Stall & Warning
13 Chapter 13: Ice, Rain & Fire Protection Systems
13.1 Ice Detection, Pneumatic Deice Boots & Electrothermal Systems 13.2 Wing & Cowl Thermal Bleed-Air Anti-Ice Systems & Rain Removal 13.3 Fire & Smoke Detection: Spot Detectors, Continuous Loops & Optical Sensors 13.4 Fire Extinguishing Systems: HRD Containers, Squibs & Two-Shot Architecture
14 Chapter 14: Airframe Inspection & Maintenance Regulations
14.1 14 CFR Part 43 Appendix D: Scope of 100-Hour & Annual Inspections 14.2 Airworthiness Directives (ADs), Service Bulletins & Major Alterations 14.3 FAA Form 337 Execution, Maintenance Record Entries & Logbook Rules 14.4 Airframe Corrosion Identification, Treatment, Chemical Conversion & NDT
15 Chapter 15: Rotorcraft Fundamentals
15.1 Rotorcraft Aerodynamics, Rotor System Classifications & Flight Controls 15.2 Rotor Blades, Transmissions, Drive Systems & Skid Landing Gear Inspection 15.3 Rotor Track & Balance, Vibration Diagnosis & Helicopter Ground Safety
16 Chapter 16: Water & Waste Systems
16.1 Potable Water Systems: Components, Operation, Servicing & Sanitizing 16.2 Lavatory Waste Systems: Vacuum & Recirculating Types, Servicing & Safety
4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
Key Takeaways Explain This Topic AI
Hi-Lok pin-and-collar fasteners provide precise structural preload without a torque wrench via a calibrated shear collar that shears off at a specific torque value.
CherryMAX mechanically locked blind rivets (NAS 9300 series) utilize a visible locking collar and retained stem to achieve shear and tensile strengths equivalent to solid AD rivets.
Structural blind bolts (Jo-Bolts, Blind Bolts) provide high-tensile and high-shear blind clamping for thick structural plate stack-ups and inaccessible wing box assemblies.
Aviation standard bolts (AN, MS, NAS) are sized by diameter in 1/16-inch increments (AN4 = 1/4" OD) and length in 1/8-inch increments (AN4-12 = 1-1/4"), with close-tolerance NAS bolts identified by an embossed triangle.
Self-locking nuts are categorized into nylon insert nuts (Elastic Stop Nuts, MS20365, limited to 250°F / 121°C) and all-metal prevailing-torque locknuts (up to 450°F–800°F); they must never be installed on joints subject to continuous rotation.
Last updated: August 2026
4.3 Special Structural Fasteners, Blind Rivets & Precision Hardware
FAA Airframe Exam Focus: Modern high-performance aircraft structures rely on specialized structural fasteners, pin-and-collar systems, mechanically locked blind rivets, close-tolerance bolts, and prevailing-torque locknuts. An AMT must understand fastener identification markings, grip length sizing formulas, hole preparation tolerances, and critical operational temperature and rotation limitations under FAA-H-8083-31A and AC 43.13-1B .
1. High-Strength Pin-and-Collar Fasteners (Hi-Lok, Hi-Tique, Hi-Lite & Lockbolts)
Pin-and-collar fasteners combine the high shear strength of an alloy steel bolt with the rapid installation and consistent clamping preload of a solid rivet. HI-LOK PIN AND COLLAR ASSEMBLY & INSTALLATION MECHANISM:
- Hi-Lok Pin Shank Threaded Collar with Shear Hex
- ┌──────────────────────────┐ ┌──────┬───────────┐
- │ Smooth Precision Shank │══════════╡░░░░░░│ █ █ █ █ █ │ ◄── Driving Hex Head
- └──────────────────────────┘ └──────┴───────────┘
- ▲ ▲ ▲
│ │ └── Torques off at calibrated limit!
- │ └───────────── Retained Threaded Collar Body
- └──────────────────────────────────────── Grip Length (Equals Material Stack)
INTERNAL ALLEN HEX IN PIN TIP:
Holds pin stationary while socket driver rotates the collar.
A. Hi-Lok Fasteners
Hi-Lok fasteners are the most prevalent high-strength permanent structural fasteners in commercial and military airframes:
Two-Piece Component Architecture:
Pin: Precision-ground shank made of alloy steel (AISI 4140/8740), titanium (6Al-4V), or corrosion-resistant stainless steel (A-286). The pin tip features a reverse internal hexagonal Allen drive recess.
Threaded Collar: An aluminum alloy (2024-T6), stainless steel, or titanium collar featuring an internal thread, a smooth base flange, a calibrated shear groove, and an outer driving hex head.
Self-Torquing Mechanical Principle:
During installation, an Allen hex key is inserted into the pin tip to prevent the pin from rotating.
A motorized or manual socket tool rotates the threaded collar onto the pin threads, drawing the structural sheets tightly together.
When the clamping preload reaches the exact engineered design limit, the shear hex head twists off cleanly at the shear groove , leaving a vibration-proof, perfectly torqued fastener.
Advantage: Eliminates the need for operator torque wrenches and guarantees consistent clamping tension across thousands of fasteners.
Inspection & Grip Rules:
The smooth pin shank must extend completely through the material stack-up. No threads are permitted to bear against the hole wall in shear.
The collar must be firmly seated against the sheet surface.
If the pin grip is slightly long, a maximum of two washers (total thickness ≤ 1 / 8 in \le 1/8\text{ in} ≤ 1/8 in ) may be installed beneath the collar.
B. Hi-Tique & Hi-Lite Fasteners
Hi-Tique: A specialized variant of the Hi-Lok pin that features a slight bead or gentle swell on the shank. As the pin is drawn into an interference-fit hole, this bead cold-works the hole bore, imparting compressive residual stresses that significantly enhance joint fatigue life in high-cycle wing structures.
Hi-Lite: An optimized lightweight version of the Hi-Lok where pin thread runout is shortened and the collar wall is thinned, providing a 15 % to 30 % 15\%\text{ to }30\% 15% to 30% weight reduction across transport-category airframes.
C. Lockbolts (Huck Bolts & CherryLOCK)
Lockbolts are heavy-duty, permanent structural fasteners that replace high-strength bolts in heavy primary joints (landing gear bulkheads, wing spar attachments):
Pull-Type Lockbolt: Features annular locking grooves (not threads) and a break-off pintail. A pneumatic pulling gun grips the pintail, pulls the sheets together under hydraulic tension, swages an unthreaded locking collar into the annular grooves, and snaps the pintail off at a calibrated breakneck groove.
Stump-Type Lockbolt: Driven in tight-clearance bays using a standard pneumatic rivet gun and bucking bar to swage the collar.
2. Mechanically Locked Blind Fasteners & Blind Rivets
Blind fasteners are designed for structural installations where the technician has physical access to only one side of the structural assembly (e.g., closed wing leading edges, control surfaces, box spars, and tubular frames). +-----------------------------------------------------------------------------------------+
- | AIRCRAFT BLIND RIVET CLASSIFICATION |
- +----------------------------+------------------------------------------------------------+
- | Fastener Category | Mechanical Locking Method & Structural Suitability |
- +----------------------------+------------------------------------------------------------+
- | Friction-Lock Blind Rivet | Stem held solely by friction; PROHIBITED in primary struct.|
- | Mechanical-Lock (CherryMAX)| Visible mechanical locking ring; APPROVED structural repl. |
- | Structural Blind Bolt | Threaded expander sleeve (Jo-Bolt); High shear/tensile use |
+----------------------------+------------------------------------------------------------+ CHERRYMAX (NAS 9300 SERIES) 4-PIECE ASSEMBLY & INSTALLATION:
- Manufactured Head Locking Collar Driving Anvil Pulling Stem
- ┌───┐ ┌──┐ ┌──┐ │
- │ │══════════════════╡ ╞══════════════════╡ ╞══════════════════╡═══════► (PULL)
- └───┘ └──┘ └──┘ │
- │ │ │ │
- Rivet Sleeve Core Expands Blind Head Drives Lock Ring Breaks at Notch
- A. Friction-Lock vs. Mechanical-Lock Blind Rivets
Friction-Lock Rivets (Non-Structural): The center pulling stem is retained inside the hollow rivet shank solely by friction. Under engine vibration and acoustic buffet, the stem vibrates loose and falls out, leaving a hollow tube with only 30 % to 40 % 30\%\text{ to }40\% 30% to 40% of solid rivet shear strength . Friction-lock rivets are strictly prohibited in primary aircraft structures.
Mechanically Locked Stem Rivets (CherryMAX / NAS 9300):
Four-Part Assembly: Consists of a tubular rivet sleeve, a blind-head forming anvil, a pulling stem with a breaknotch, and a mechanical locking ring (collar) .
Installation Mechanics:
The pneumatic pulling tool pulls the stem while holding the sleeve against the outer sheet.
The stem head expands the blind end of the sleeve into a large, flat, fully formed shop head.
As pulling continues, the driving anvil forces the mechanical locking collar into a precision chamfer in the rivet head, permanently locking the stem to the sleeve.
The stem fractures cleanly at the engineered breaknotch flush with the manufactured head.
Structural Equivalence: Because the locked stem cannot fall out, CherryMAX rivets provide shear and tensile strengths equivalent to standard solid MS20470AD (2117-T4) rivets and are approved as direct structural replacements on a diameter-for-diameter basis.
Visual Quality Inspection: A correctly installed CherryMAX rivet must have its locking collar completely seated flush in the head recess and the stem broken flush (within ± 0.010 in \pm 0.010\text{ in} ± 0.010 in ) with the head surface.
B. Structural Blind Bolts (Jo-Bolt & Visu-Lok)
Jo-Bolts and Visu-Loks are ultra-high-strength three-piece blind structural fasteners consisting of an alloy steel or titanium outer threaded sleeve, a driving nut, and an inner bolt core:
As the bolt core is driven, it pulls the tapered nut into the sleeve, expanding the sleeve against the blind sheet surface and torquing the threaded joint to extreme preload.
Application: Used in heavy-gauge wing skins, landing gear fittings, and heavily loaded structural joints where solid bolts cannot be bucked.
3. Hole Preparation, Precision Reaming & Interference Fits
High-strength structural fasteners require precise hole geometry to ensure equal load distribution and prevent fatigue failure. HOLE FIT CLASSIFICATIONS IN AIRCRAFT STRUCTURES:
- 1. CLEARANCE FIT (Standard Rivets & General Bolts)
- Hole Diameter > Fastener Shank Diameter (+0.002" to +0.004" Clearance)
- Fastener slides through hole by hand with zero resistance.
- 2. INTERFERENCE FIT (Hi-Lok & Taper-Lok in High-Fatigue Wing Skins)
- Hole Diameter < Fastener Shank Diameter (-0.0010" to -0.0025" Interference)
- Pin driven with light mallet or hydraulic puller; pre-stresses hole wall in compression,
preventing fatigue crack initiation under cyclic flight tension.
A. Drilling, Reaming & Deburring Standards
Pilot Drilling & Step Reaming: Holes for close-tolerance fasteners must never be drilled directly to final size. The hole is pilot-drilled undersize (e.g., 1 / 64 to 1 / 32 in 1/64\text{ to }1/32\text{ in} 1/64 to 1/32 in under) and brought to final dimensions using a high-speed spiral-flute precision reamer .
Surface Finish (Roughness): Reamed holes for NAS bolts and Hi-Loks must achieve a surface finish of 32 to 63 micro-inches 32\text{ to }63\text{ micro-inches} 32 to 63 micro-inches ( R a Ra R a ) . Rough drill scores act as stress risers that initiate fatigue cracks.
Deburring: Both hole exits must be deburred using a dedicated zero-flute or rotating deburring blade. However, never create a deep countersink or chamfer during deburring—removing excess edge metal weakens the bearing surface and causes fastener head knife-edging.
4. Aviation Bolt Identification & Standard Hardware (AN, MS, NAS)
Aircraft structural bolts are manufactured to rigid military and aerospace standards (AN = Air Force-Navy, MS = Military Standard, NAS = National Aerospace Standard). +-----------------------------------------------------------------------------------------+
- | AIRCRAFT BOLT HEAD MARKING IDENTIFICATION |
- +--------------------------+------------------------------+-------------------------------+
- | Bolt Specification | Head Physical Marking | Material & Tensile Strength |
- +--------------------------+------------------------------+-------------------------------+
- | Standard Steel (AN3-AN20)| Raised Cross (+) or Asterisk | SAE 4037/8740 Steel (125 ksi) |
- | Close-Tolerance (NAS) | Raised Triangle (Δ) | Ground Alloy Steel (160 ksi) |
- | Corrosion-Resistant (CRES)| Single Raised Dash (-) | Stainless Steel (A-286/304) |
- | Aluminum Alloy (AN) | Two Raised Dashes (--) | 2024-T4 Aluminum (62 ksi) |
- | Magnetically Inspected | Stamped 'M' or Orange Paint | Certified MPI Tested |
+--------------------------+------------------------------+-------------------------------+ BOLT HEAD MARKING GUIDE:
- Standard Steel Close-Tolerance Stainless (CRES) Aluminum Alloy Special Magnetic
- ┌───┐ ┌───┐ ┌───┐ ┌───┐ ┌───┐
- │ + │ │ Δ │ │ ─ │ │ ═ │ │ M │
- └───┘ └───┘ └───┘ └───┘ └───┘
- 125 ksi Alloy Ground Shank A-286 CRES 2024-T4 Al MPI Certified
- A. Decrypting the Standard AN Bolt Part Number System
Standard aircraft hex head bolts are designated by the AN prefix followed by diameter and length codes: A N [ D i a m e t e r ] − [ L e n g t h ] [ S u f f i x ] \mathbf{AN[Diameter]-[Length][Suffix]} AN [ Diameter ] − [ Length ] [ Suffix ]
Diameter Code (in 1 / 16 -inch 1/16\text{-inch} 1/16 -inch increments):
AN3 = 3 / 16 in 3/16\text{ in} 3/16 in ( 0.1875 in 0.1875\text{ in} 0.1875 in )
AN4 = 4 / 16 in = 1 / 4 in 4/16\text{ in} = 1/4\text{ in} 4/16 in = 1/4 in ( 0.2500 in 0.2500\text{ in} 0.2500 in )
AN5 = 5 / 16 in 5/16\text{ in} 5/16 in ( 0.3125 in 0.3125\text{ in} 0.3125 in )
AN6 = 6 / 16 in = 3 / 8 in 6/16\text{ in} = 3/8\text{ in} 6/16 in = 3/8 in ( 0.3750 in 0.3750\text{ in} 0.3750 in )
AN8 = 8 / 16 in = 1 / 2 in 8/16\text{ in} = 1/2\text{ in} 8/16 in = 1/2 in ( 0.5000 in 0.5000\text{ in} 0.5000 in )
AN20 = 20 / 16 in = 1 − 1 / 4 in 20/16\text{ in} = 1-1/4\text{ in} 20/16 in = 1 − 1/4 in ( 1.2500 in 1.2500\text{ in} 1.2500 in )
Length Code (in 1 / 8 -inch 1/8\text{-inch} 1/8 -inch increments):
Lengths under 1 inch: Single digit representing eighths of an inch (e.g., AN4-7 = 1 / 4 in 1/4\text{ in} 1/4 in diameter, 7 / 8 in 7/8\text{ in} 7/8 in long).
Lengths of 1 inch and greater: First digit represents whole inches, and second digit represents additional eighths of an inch:
AN4-12 = 1 in + 2 / 8 in = 1 − 1 / 4 in 1\text{ in} + 2/8\text{ in} = 1-1/4\text{ in} 1 in + 2/8 in = 1 − 1/4 in total length
AN6-24 = 2 in + 4 / 8 in = 2 − 1 / 2 in 2\text{ in} + 4/8\text{ in} = 2-1/2\text{ in} 2 in + 4/8 in = 2 − 1/2 in total length
Hole Drilling Suffix Codes:
Standard A Suffix (e.g., AN4-12A ): Designates an undrilled bolt shank (used with self-locking nuts).
Absence of A (e.g., AN4-12 ): Designates a drilled shank with a cotter pin hole through the threads (used with castle nuts).
H Prefix (e.g., AN4H-12A ): Designates a drilled head with a safety wire hole through the hex head.
C Code (e.g., AN4C-12A ): Designates corrosion-resistant stainless steel .
DD Code (e.g., AN4DD-12A ): Designates 2024-T4 aluminum alloy .
B. Close-Tolerance, Clevis & Internal Wrenching Bolts
Close-Tolerance Bolts (NAS / MS20004 to MS20024): Ground to ultra-precise shank diameters ( ± 0.0005 in \pm 0.0005\text{ in} ± 0.0005 in ). Identified by an embossed triangle ( Δ \Delta Δ ) on the head . Mandatory for structural joints subject to severe alternating shear and dynamic reversal loads (wing spar root fittings, flight control hinges).
Clevis Bolts (AN21 to AN36): Feature a shallow, rounded head with a screwdriver or cross-recess slot and a short thread length. Designed strictly for pure shear loads (e.g., control cable fork ends); prohibited in tension applications.
Internal Wrenching Bolts (NAS144 to NAS158 / MS2114): High-strength steel alloy bolts ( 160 – 180 ksi 160\text{--}180\text{ ksi} 160 – 180 ksi ) featuring an internal Allen hex drive. Used in high-tension applications (engine mounts, landing gear trunnions). Must always be installed with dedicated heat-treated MS chamfered washers under the head to seat against the large head-to-shank fillet radius.
5. Self-Locking Nuts, Castle Nuts & Installation Restrictions
Aviation nuts must remain locked securely under extreme flight vibration and thermal expansion cycles. +-----------------------------------------------------------------------------------------+
- | AIRCRAFT LOCKNUT CLASSIFICATION & LIMITS |
- +--------------------------+-----------------------+--------------------------------------+
- | Nut Type | Temperature Limit | Core Operating Limitation |
- +--------------------------+-----------------------+--------------------------------------+
- | Nylon Insert (MS20365) | 250°F (121°C) Max | NO high temp / NO continuous rotation|
- | All-Metal (MS21042) | 450°F to 800°F | NO continuous relative rotation |
- | Castle Nut (AN310) | Temperature rated | REQUIRES cotter pin or safety wire |
+--------------------------+-----------------------+--------------------------------------+ SELF-LOCKING NUT INTERNAL LOCKING MECHANISMS:
- 1. ELASTIC STOP NUT (Nylon / Fiber Insert - MS20365)
- ┌───────────────┐
- │ █ █ █ █ █ │ ◄── Unthreaded Resilient Nylon Collar (Max 250°F)
- ├───┬───────┬───┤
- │ ░ │ │ ░ │ ◄── Standard Threaded Steel Body
- └───┴───────┴───┘
- 2. ALL-METAL PREVAILING TORQUE NUT (MS21042 / Beam Type)
- ┌───\───────/───┐
- │ ░ \ / ░ │ ◄── Out-of-Round Crimped Crown / Slotted Locking Beams
- ├───┬───────┬───┤ (Withstands 450°F to 800°F on Engine Firewalls)
- │ ░ │ │ ░ │
- └───┴───────┴───┘
- A. Elastic Stop Nuts (Nylon Insert / MS20365 / NASM20365)
Elastic Stop Nuts incorporate an unthreaded fiber or nylon locking insert ring inside the crown of the nut:
As the bolt threads penetrate the nylon ring, the nylon deforms elastically around the bolt threads, exerting continuous compressive frictional pressure ( prevailing torque ).
Operating Temperature Limit: The nylon insert degrades, softens, and loses elasticity at elevated temperatures. Elastic stop nuts are strictly limited to locations where operating temperatures do not exceed 250 ∘ F 250^\circ\text{F} 25 0 ∘ F ( 121 ∘ C 121^\circ\text{C} 12 1 ∘ C ) . They are prohibited on engine firewalls, exhaust manifolds, turbocharger mounts, or wheel brake assemblies.
B. All-Metal Self-Locking Nuts (MS21042 / NAS1291)
All-metal locknuts achieve prevailing locking torque by deforming the metal threads in the top crown (elliptical crimping or slotted flexible beams):
Because they contain no polymer inserts, cadmium-plated carbon steel all-metal locknuts operate safely up to 450 ∘ F 450^\circ\text{F} 45 0 ∘ F ( 232 ∘ C 232^\circ\text{C} 23 2 ∘ C ) , while corrosion-resistant A-286 / Inconel locknuts operate up to 800 ∘ F– 1 , 200 ∘ F 800^\circ\text{F}\text{--}1,200^\circ\text{F} 80 0 ∘ F – 1 , 20 0 ∘ F on engine exhaust systems.
C. Critical Installation Rules & Prohibitions for Locknuts
The Continuous Rotation Prohibition: Self-locking nuts must NEVER be installed on bolts, pins, or joints subject to continuous relative rotation (such as control surface hinges, landing gear retract pivots, or throttle bellcranks). Frictional rotation against the nut face will back the nut off the bolt threads, causing catastrophic joint disassembly. Castle nuts (AN310) with cotter pins are mandatory for all pivoting/rotating joints.
Thread Protrusion Standard: When installed, a minimum of two full threads of the bolt shank must extend completely through the locking crown of any self-locking nut or castle nut to ensure 100% engagement with the locking element.
Reusability & Breakaway Torque Testing: Self-locking nuts may be reused provided the locking element retains adequate prevailing torque. If an AMT can thread the nut onto the bolt by hand fingers alone past the locking element, the nut has lost its frictional locking grip and must be discarded and replaced immediately .