Study guide
5.4 Aircraft Finishing Systems, Registration Markings & Placards
FAA Aviation Mechanic — General AMG
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & AMG Exam Overview
1.1 About the FAA Aviation Mechanic General Knowledge Test 1.2 How to Study for the AMG Exam
2 Chapter 2: Maintenance Forms, Records, Publications & Regulations
2.1 14 CFR Parts 43, 65, and 91 Regulatory Framework 2.2 Aviation Mechanic Privileges, Limitations & Recent Experience 2.3 Maintenance Recordkeeping & Return-to-Service Entries (14 CFR 43.9 & 43.11) 2.4 FAA Form 337 Major Repairs and Major Alterations 2.5 Airworthiness Directives (ADs) & Mandatory Compliance 2.6 Type Certificate Data Sheets (TCDS), STCs, ACs & Maintenance Manuals 2.7 FAA Forms, MMEL/MEL, Inoperative Equipment & Parts Effectivity
3 Chapter 3: Basic Electricity
3.1 DC Electrical Circuits, Ohm's Law & Power 3.2 AC Electrical Fundamentals, Reactance & Impedance 3.3 Aircraft Lead-Acid & Nickel-Cadmium Storage Batteries 3.4 DC Generators, Alternators & Electric Motors 3.5 Aircraft Wiring, Bonding & Circuit Protection Devices 3.6 Resistor Color Codes, Semiconductors, Digital Logic & Electrostatic Discharge
4 Chapter 4: Materials & Processes
4.1 Aircraft Ferrous and Nonferrous Metals & Heat Treatment 4.2 Metal Hardness Testing (Rockwell, Brinell, Vickers) 4.3 Nondestructive Testing (NDT/NDI) Inspection Methods 4.4 Aircraft Hardware, Fasteners & Safetying Methods 4.5 Composite Materials, Plastics & Control Cables 4.6 Soldering, Welding & Weld Quality Inspection
5 Chapter 5: Cleaning & Corrosion Control
5.1 Corrosion Types, Chemistry & Identification 5.2 Corrosion Removal, Chemical Conversion Coatings & Surface Treatments 5.3 Aircraft Cleaning Agents, Precautions & Preventative Maintenance 5.4 Aircraft Finishing Systems, Registration Markings & Placards
6 Chapter 6: Weight & Balance
6.1 Weight and Balance Terminology, Datum, Arm & Moment Principles 6.2 Aircraft Weighing Procedures, Scale Reactions & Tare Weight 6.3 Center of Gravity Computations, Extreme Loading & Ballast
7 Chapter 7: Ground Operation, Servicing & Safety
7.1 Engine Starting Procedures, Danger Areas & Ground Taxi Safety 7.2 Aircraft Servicing (Oxygen, Hydraulic, Pneumatic & De-Icing Fluids) 7.3 Aircraft Fueling Safety, Static Grounding & Hangar Fire Protection 7.4 Airport Movement Areas, Hazardous Materials, Tool Control & FOD Prevention
8 Chapter 8: Aircraft Drawings
8.1 Aircraft Drawing Types, Title Blocks & Orthographic Projections 8.2 Line Conventions, Dimensions, Tolerances & Material Symbols 8.3 Electrical Wiring Diagrams, Logic Flowcharts & Fluid Schematics
9 Chapter 9: Fluid Lines & Fittings
9.1 Rigid Metal Tubing Fabrication, Bending & 37° AN Flaring 9.2 Flexible Hose Construction, Pressure Ratings & Lay Lines 9.3 AN/MS/Quick-Disconnect Fittings, Identification & Installation
10 Chapter 10: Mathematics for Aviation Maintenance
10.1 Fractions, Decimals, Percentages & Ratio/Proportion 10.2 Geometric Computations (Area, Volume & Cylinder Displacement) 10.3 Algebraic Equations, Powers, Roots & Maintenance Conversions
11 Chapter 11: Physics for Aviation Maintenance
11.1 Matter, Mass, Weight, Density & Specific Gravity 11.2 Work, Energy, Power & Simple Machines (Mechanical Advantage) 11.3 Fluid Mechanics, Pascal's Law & Bernoulli's Principle 11.4 Thermodynamics, Heat Transfer, Gas Laws, Sound & Aerodynamics 11.5 Standard Atmosphere, Density & Pressure Altitude, Flight Controls & Aerodynamic Devices
12 Chapter 12: Inspection Concepts, Techniques & Precision Measurement
12.1 Aircraft Inspection Programs & Inspection Concepts 12.2 Precision Measuring Tools & Tool Calibration
13 Chapter 13: Human Factors in Aviation Maintenance
13.1 Human Error, the Dirty Dozen & Maintenance Safety Culture 13.2 Human Performance, Limitations, Fatigue & the Work Environment 13.3 Communication, Shift Turnover, Event Investigation & Professionalism
5.4 Aircraft Finishing Systems, Registration Markings & Placards
Key Takeaways Explain This Topic AI
An aircraft finish is a stack: clean substrate, chemical conversion coating or anodize, primer, then topcoat, and skipping a layer is what causes adhesion failure.
Blushing comes from high humidity, orange peel from viscosity or pressure, and fisheye from silicone or oil contamination, while peeling almost always traces to improper surface preparation.
14 CFR 45.29 requires nationality and registration marks at least 12 inches high on fixed-wing aircraft and rotorcraft, with 3-inch marks reserved for gliders, balloons, airships, powered parachutes, weight-shift-control aircraft, and specified experimental categories.
Registration characters must be two-thirds as wide as they are high, formed by lines one-sixth as thick as the character height, with spacing of at least one-fourth of the character width.
Any control surface must be rebalanced to the manufacturer's specification after refinishing, because paint weight added aft of the hinge line can induce destructive flutter.
Last updated: August 2026
5.4 Aircraft Finishing Systems, Registration Markings & Placards
ACS Subject AM.I.G is the second-largest General subject at 24 knowledge elements, and roughly half of them are about finishing rather than corrosion chemistry: materials used for protection of airframe structures ( K14 ), primer materials ( K15 ), topcoat materials ( K16 ), surface preparation ( K17 ), effects of ambient conditions ( K18 ), effects of improper surface preparation ( K19 ), regulatory requirements for replacing identification, registration markings, and placards ( K20 ), inspection of aircraft finishes ( K21 ), safety practices when using finishing materials ( K22 ), application techniques ( K23 ), and control surface balance after refinishing ( K24 ). This section covers that half.
1. The Finishing System Is a Stack, Not a Coat
An aircraft finish is a layered system, and each layer has a job. Skipping or substituting a layer is what causes the failures in Section 3. +-------------------------------------------------------------------------+
- | TYPICAL METAL AIRCRAFT FINISHING STACK |
- +-------------------------------------------------------------------------+
- | 4. TOPCOAT Polyurethane / acrylic lacquer / enamel |
- | -> color, gloss, UV and chemical resistance |
- |-------------------------------------------------------------------------|
- | 3. PRIMER Epoxy, wash (etch), or zinc chromate primer |
- | -> adhesion bridge + corrosion inhibition |
- |-------------------------------------------------------------------------|
- | 2. CONVERSION Chemical conversion coating (chromate / Alodine) or |
- | COATING anodize on aluminum |
- | -> converts bare metal into a paint-receptive, |
- | corrosion-inhibiting film |
- |-------------------------------------------------------------------------|
- | 1. SUBSTRATE Clean, deoxidized, dry bare metal or prepared composite |
- +-------------------------------------------------------------------------+
- Primer materials (K15)
Wash primer (etching primer) — a thin two-part phosphoric-acid primer that etches and passivates in one step. It is a base for a following primer , not a standalone finish.
Zinc chromate primer — the classic yellow-green inhibiting primer; the chromate ion actively suppresses corrosion at scratches. Its use is increasingly restricted for health and environmental reasons, so always check the current manufacturer's specification.
Epoxy primer — a two-part primer with excellent adhesion and chemical and fluid resistance; the modern default under polyurethane.
Urethane primer / primer-surfacer — used where a filling, sandable base is needed.
Topcoat materials (K16)
Polyurethane — the current standard for metal aircraft: high gloss retention, excellent resistance to Skydrol, fuel, and UV. Two-part, and the isocyanate component demands supplied-air respiratory protection.
Acrylic lacquer — fast drying, easy to spot-repair, but soft and solvent-sensitive.
Enamel — single-stage, tough, less glossy, historically common on general aviation aircraft.
Nitrate and butyrate dope — for fabric-covered aircraft only. Nitrate dope is used as the first coat because it adheres to fabric better; butyrate is used for subsequent coats because it is less flammable and shrinks more predictably.
2. Surface Preparation and Application (K17, K23)
The industry maxim is that a paint job is 90% preparation . The sequence for bare aluminum is: clean and degrease, remove old finish if required, mechanically abrade or chemically deoxidize, rinse, dry, apply chemical conversion coating, rinse, dry, prime within the manufacturer's specified window, then topcoat within the primer's recoat window.
Application technique. Hold the spray gun perpendicular to the surface at the manufacturer's stated distance (commonly 6 to 10 inches), move the gun parallel to the surface at a steady rate, and overlap each pass by roughly 50% . Arcing the gun in a swinging arc puts more material at the center of the stroke and less at each end, producing banding.
3. Ambient Conditions and Preparation Failures (K18, K19)
Defect Appearance Cause
Blushing Milky, cloudy white haze in the film Spraying lacquer or dope in high humidity or when the temperature drops; solvent evaporation chills the surface and moisture condenses into the wet film
Fisheye Small round craters where paint pulls away from a point Silicone or oil contamination on the surface or in the shop air supply
Orange peel Dimpled, pebbly texture Paint too viscous, air pressure too low, gun too far away, or ambient temperature too high
Runs and sags Curtains of paint Too much material applied at once, paint too thin, gun too close or too slow
Pinholes Tiny holes through the film Trapped solvent or moisture, or air in the substrate escaping through the film
Peeling and flaking Sheets of finish lifting Improper surface preparation — residual grease, incomplete deoxidizing, missed conversion coating, or exceeding the primer's recoat window
Sanding scratches showing through Visible scratch pattern Too coarse an abrasive during preparation
The exam pattern is consistent: environmental defects (blushing, orange peel) come from air and temperature, while adhesion defects (peeling, fisheye) come from contamination and preparation.
4. Inspecting the Finish (K21)
A finish inspection looks for more than cosmetics. Report and investigate:
Blistering — often a sign of corrosion or moisture underneath the film, not a paint defect.
Chalking and loss of gloss — UV degradation of the topcoat, reducing its barrier value.
Crazing and cracking — brittle film, often from excessive film thickness or age.
Chipping around fasteners and leading edges — bare metal exposed; a corrosion initiation site that must be touched up.
Filiform corrosion — worm-like tracks under the film, typically starting at a scratch or fastener; a specific corrosion mode driven by high humidity under an intact-looking coating.
5. Identification, Registration Markings, and Placards (K20)
This is a regulatory element, and the numbers are testable.
Aircraft identification plate — 14 CFR § 45.11 and § 45.13. The identification data must include the builder's name, model designation, builder's serial number, type certificate number (if any), production certificate number (if any), and, for engines, the established rating . Section 45.13(b) generally prohibits removing, changing, or placing identification information on an aircraft, engine, propeller, or appliance without FAA approval — a rule aimed squarely at obscuring an aircraft's identity.
Registration markings — 14 CFR Part 45 Subpart C. The key sizes under § 45.29 :
- Aircraft class Minimum mark height
- Fixed-wing aircraft 12 inches
- Gliders 3 inches
Certain experimental exhibition, amateur-built, and former or kit-built light-sport aircraft whose maximum cruising speed does not exceed 180 knots CAS 3 inches
- Airships, balloons, powered parachutes, weight-shift-control aircraft 3 inches
- Rotorcraft 12 inches
Character geometry is also specified: characters must be two-thirds as wide as they are high (except the numeral 1 , which is one-sixth as wide as it is high, and the letters M and W , which may be as wide as they are high); lines forming the characters must be one-sixth as thick as the character is high ; and the space between characters must be at least one-fourth of the character width .
Practical consequence for the painter: when you strip and repaint an aircraft, you must restore the marks to the correct size, spacing, and contrasting color, and you must not obliterate or relocate the identification plate. Operating limitation placards required by the Type Certificate Data Sheet, the Aircraft Flight Manual, or an STC must likewise be replaced in their original locations — 14 CFR § 91.9 prohibits operating an aircraft without the required placards and markings being in place and legible.
6. Control Surface Balance After Refinishing (K24)
This is the finishing element with the most serious consequence. Paint is weight, and weight added aft of the hinge line changes the static balance of a control surface. An out-of-balance surface can develop flutter — a divergent aeroelastic oscillation capable of destroying the surface, and with it the aircraft, in seconds.
Rules to carry into the exam and the hangar:
After refinishing any control surface — aileron, elevator, rudder, tab — rebalance it to the manufacturer's specification before reinstallation, unless the manufacturer's data explicitly states rebalancing is not required.
Excess paint is the usual culprit. Repeated repaints without stripping stack film thickness aft of the hinge line.
Balance is checked with the surface removed and supported at the hinge line, with all hardware, tabs, and seals installed exactly as they fly.
If a surface is out of limits, the correction is made with the balance weight specified by the manufacturer — never with an improvised weight or by removing structure.
Safety when finishing (K22): finishing materials are flammable and toxic. Spray only in an approved, properly ventilated booth with explosion-proof lighting, bond and ground the spray equipment and the aircraft, and use the personal protective equipment the Safety Data Sheet specifies. Two-part polyurethanes containing isocyanates require supplied-air respiratory protection — a cartridge respirator is not adequate.