Study guide

12.2 Precision Measuring Tools & Tool Calibration

FAA Aviation Mechanic — General AMG

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & AMG Exam Overview

1.1 About the FAA Aviation Mechanic General Knowledge Test 1.2 How to Study for the AMG Exam

2 Chapter 2: Maintenance Forms, Records, Publications & Regulations

2.1 14 CFR Parts 43, 65, and 91 Regulatory Framework 2.2 Aviation Mechanic Privileges, Limitations & Recent Experience 2.3 Maintenance Recordkeeping & Return-to-Service Entries (14 CFR 43.9 & 43.11) 2.4 FAA Form 337 Major Repairs and Major Alterations 2.5 Airworthiness Directives (ADs) & Mandatory Compliance 2.6 Type Certificate Data Sheets (TCDS), STCs, ACs & Maintenance Manuals 2.7 FAA Forms, MMEL/MEL, Inoperative Equipment & Parts Effectivity

3 Chapter 3: Basic Electricity

3.1 DC Electrical Circuits, Ohm's Law & Power 3.2 AC Electrical Fundamentals, Reactance & Impedance 3.3 Aircraft Lead-Acid & Nickel-Cadmium Storage Batteries 3.4 DC Generators, Alternators & Electric Motors 3.5 Aircraft Wiring, Bonding & Circuit Protection Devices 3.6 Resistor Color Codes, Semiconductors, Digital Logic & Electrostatic Discharge

4 Chapter 4: Materials & Processes

4.1 Aircraft Ferrous and Nonferrous Metals & Heat Treatment 4.2 Metal Hardness Testing (Rockwell, Brinell, Vickers) 4.3 Nondestructive Testing (NDT/NDI) Inspection Methods 4.4 Aircraft Hardware, Fasteners & Safetying Methods 4.5 Composite Materials, Plastics & Control Cables 4.6 Soldering, Welding & Weld Quality Inspection

5 Chapter 5: Cleaning & Corrosion Control

5.1 Corrosion Types, Chemistry & Identification 5.2 Corrosion Removal, Chemical Conversion Coatings & Surface Treatments 5.3 Aircraft Cleaning Agents, Precautions & Preventative Maintenance 5.4 Aircraft Finishing Systems, Registration Markings & Placards

6 Chapter 6: Weight & Balance

6.1 Weight and Balance Terminology, Datum, Arm & Moment Principles 6.2 Aircraft Weighing Procedures, Scale Reactions & Tare Weight 6.3 Center of Gravity Computations, Extreme Loading & Ballast

7 Chapter 7: Ground Operation, Servicing & Safety

7.1 Engine Starting Procedures, Danger Areas & Ground Taxi Safety 7.2 Aircraft Servicing (Oxygen, Hydraulic, Pneumatic & De-Icing Fluids) 7.3 Aircraft Fueling Safety, Static Grounding & Hangar Fire Protection 7.4 Airport Movement Areas, Hazardous Materials, Tool Control & FOD Prevention

8 Chapter 8: Aircraft Drawings

8.1 Aircraft Drawing Types, Title Blocks & Orthographic Projections 8.2 Line Conventions, Dimensions, Tolerances & Material Symbols 8.3 Electrical Wiring Diagrams, Logic Flowcharts & Fluid Schematics

9 Chapter 9: Fluid Lines & Fittings

9.1 Rigid Metal Tubing Fabrication, Bending & 37° AN Flaring 9.2 Flexible Hose Construction, Pressure Ratings & Lay Lines 9.3 AN/MS/Quick-Disconnect Fittings, Identification & Installation

10 Chapter 10: Mathematics for Aviation Maintenance

10.1 Fractions, Decimals, Percentages & Ratio/Proportion 10.2 Geometric Computations (Area, Volume & Cylinder Displacement) 10.3 Algebraic Equations, Powers, Roots & Maintenance Conversions

11 Chapter 11: Physics for Aviation Maintenance

11.1 Matter, Mass, Weight, Density & Specific Gravity 11.2 Work, Energy, Power & Simple Machines (Mechanical Advantage) 11.3 Fluid Mechanics, Pascal's Law & Bernoulli's Principle 11.4 Thermodynamics, Heat Transfer, Gas Laws, Sound & Aerodynamics 11.5 Standard Atmosphere, Density & Pressure Altitude, Flight Controls & Aerodynamic Devices

12 Chapter 12: Inspection Concepts, Techniques & Precision Measurement

12.1 Aircraft Inspection Programs & Inspection Concepts 12.2 Precision Measuring Tools & Tool Calibration

13 Chapter 13: Human Factors in Aviation Maintenance

13.1 Human Error, the Dirty Dozen & Maintenance Safety Culture 13.2 Human Performance, Limitations, Fatigue & the Work Environment 13.3 Communication, Shift Turnover, Event Investigation & Professionalism

12.2 Precision Measuring Tools & Tool Calibration

Key Takeaways Explain This Topic AI

A standard micrometer spindle has 40 threads per inch, so one thimble revolution advances 0.025 inch and each of the 25 thimble divisions equals 0.001 inch; a Vernier scale extends resolution to 0.0001 inch.

Small-hole and telescoping gauges are transfer gauges: they are set in the bore and then measured with a micrometer, which supplies the actual number.

Concentricity is checked with a dial indicator while rotating the shaft one full revolution; the full needle sweep is the total indicator reading and the actual eccentricity is half of it.

A calibration program requires traceability to NIST, a defined interval, a visible status label, records, and out-of-tolerance recall of work measured since the last good calibration.

A tool past its calibration due date must be removed from service, and click-type torque wrenches must be stored backed off to their lowest setting rather than at full scale.

Last updated: August 2026

12.2 Precision Measuring Tools & Tool Calibration

Two ACS elements sit here and both are examinable: measuring tools including calipers, micrometers, and gauges ( AM.I.K.K1 ) and calibration and tool accuracy requirements ( AM.I.K.K2 ). Subject E adds precision measurement tools, principles, and procedures ( AM.I.E.K6 ). The associated skills — use Vernier calipers ( AM.I.K.S1 ), use micrometers ( S2 ), use measurement gauges ( S3 ), make precision measurements with a Vernier-scale instrument ( AM.I.E.S6 ), check the concentricity of a shaft ( AM.I.E.S7 ), and check a micrometer for proper calibration ( AM.I.E.S14 ) — are all practical-test projects, so read this section as preparation for both the written and the shop.

1. Reading a Micrometer

The standard outside micrometer with a 1-inch range resolves to 0.001 inch . Its geometry is fixed and worth understanding rather than memorizing: the spindle thread has 40 threads per inch , so one full turn of the thimble advances the spindle exactly 1/40 inch = 0.025 inch . The thimble is divided into 25 equal parts , so one thimble division equals 0.025 / 25 = 0.001 inch .

Reading procedure:

Read the largest whole number visible on the sleeve — each numbered division is 0.100 inch .

Add 0.025 inch for each additional sleeve line visible past that number.

Add the thimble reading in thousandths, taken at the line coinciding with the sleeve's horizontal datum line.

Worked example. The sleeve shows the number 2 with three additional lines exposed, and the thimble reads 17 .

0.200 + (3 x 0.025) + 0.017 = 0.200 + 0.075 + 0.017 = 0.292 inch

The Vernier micrometer adds a third scale of ten lines along the top of the sleeve, extending resolution to 0.0001 inch . Find the one Vernier line that exactly coincides with a thimble line and add that many ten-thousandths. If Vernier line 4 coincides in the example above, the reading becomes 0.2924 inch .

Micrometer families you must recognize: outside micrometer (general measurement), inside micrometer (bore diameters), depth micrometer (hole and step depths — note that its scale reads backwards relative to an outside micrometer), thread micrometer with a pointed anvil and a V-anvil (pitch diameter), screw-thread comparator , and the ball-anvil micrometer for wall thickness on curved parts such as tubing.

2. Reading a Vernier Caliper

The common inch Vernier caliper carries a main (bar) scale divided into 0.025-inch increments and a Vernier scale of 25 divisions spanning 24 main-scale divisions, giving 0.001-inch resolution.

Read the main scale at the Vernier zero: whole inches, tenths, then the number of 0.025 divisions.

Scan the Vernier scale for the one line that coincides exactly with a main-scale line; that Vernier number is the thousandths to add.

Worked example. The Vernier zero sits just past 1.450 with two further 0.025 divisions exposed, and Vernier line 12 coincides.

1.450 + (2 x 0.025) + 0.012 = 1.450 + 0.050 + 0.012 = 1.512 inch

A caliper measures outside, inside, depth, and step , which makes it the most versatile of the precision instruments — but its long, relatively flexible jaws make it less accurate than a micrometer for a critical diameter. When a tolerance is tight, use a micrometer.

3. Gauges (AM.I.K.S3)

Gauge Use Technique note

Thickness (feeler) gauge Valve clearance, gaps, shim selection Correct feel is a light drag, not a push; stacking blades is permitted but adds error

Small-hole (ball) gauge Small bores; expanded in the bore, then measured with a micrometer It is a transfer gauge — the micrometer, not the gauge, gives the number

Telescoping gauge Larger bores; same transfer principle Rock the gauge through the bore's diameter to find the true maximum

  • Dial indicator Runout, concentricity, end play, warp Mount rigidly; a flexible mount ruins the reading
  • Thread pitch gauge Identify threads per inch Compare against the fastener until a blade seats fully
  • Go / No-Go gauge Swaged cable sleeves, hole limits Go must pass fully; No-Go must not enter at all
  • Twist drill gauge Verify drill diameter Prevents oversized holes in structural repairs

Checking the concentricity of a shaft (AM.I.E.S7). Support the shaft in matched V-blocks or between centers, set a dial indicator perpendicular to the surface at the specified station, preload the indicator, zero it, and rotate the shaft one full revolution while watching the needle. The full sweep between the highest and lowest readings is the total indicator reading (TIR) , also called runout. The actual eccentricity of the axis is half the TIR. Compare TIR to the manufacturer's limit — a bent propeller shaft, crankshaft, or landing gear axle is condemned by this measurement.

4. Calibration and Tool Accuracy (AM.I.K.K2)

An instrument that has not been verified is not a measuring tool; it is a source of confident, documented error. A conforming calibration program has five features:

Traceability. Working standards are traceable to a national standard — in the United States, the National Institute of Standards and Technology (NIST) .

A defined interval, set by the manufacturer's recommendation, the quality system, or usage history. Torque wrenches, micrometers, dial indicators, weighing scales, and electrical test equipment all carry intervals.

A visible status label on the tool showing the calibration date, the due date, and the calibrating agency. A tool that is out of calibration date must be removed from service — using it, even if it "seems fine," invalidates the measurement.

Records linking each tool to its certificate and history.

Out-of-tolerance recall. If a tool is found out of tolerance at calibration, the organization must evaluate and, where necessary, re-inspect the work measured with it since its last good calibration. That is why a dropped micrometer must be pulled and re-certified rather than quietly returned to the drawer.

Checking a micrometer's calibration (AM.I.E.S14). For a 0-to-1-inch micrometer, clean the anvil and spindle faces with a lint-free wipe, close them using the ratchet or friction thimble — never brute force on the barrel — and confirm the thimble zero aligns with the sleeve datum. If it does not, adjust with the spanner wrench supplied with the instrument. For a micrometer with a range that does not close to zero, and for a full accuracy check at any range, verify against a gauge block or the manufacturer's standard . Also check for anvil wear and parallelism with an optical flat or by measuring a gauge block at several points across the anvil face.

Torque wrench calibration deserves its own note because AM.I.E.K10 ties torque to fastener preload. Torque is only a proxy for the clamping preload you actually want; friction can consume 80 to 90 percent of applied torque. An out-of-calibration wrench therefore does not produce a slightly wrong preload — it can produce a joint that is loose enough to fret or tight enough to yield the fastener. Store click-type wrenches backed off to their lowest setting , never at full scale, and never use a cheater bar or an extension unless you apply the extension formula from Section 9.3.

5. Handling Rules That Preserve Accuracy

Let a tool and the part reach the same temperature before measuring. Steel expands about 0.0000063 inch per inch per degree Fahrenheit; on a 6-inch dimension, a 30 °F difference is more than a thousandth.

Hold instruments by their insulated frames or pads to keep body heat out of the measurement.

Never measure a rotating part , and never use a micrometer as a C-clamp or a caliper as a scriber.

Clean measuring faces before every use; a single chip under an anvil is a thousandth of error.

Store instruments in their cases, slightly open , lightly oiled, away from vibration and coolant.

Repeat the measurement. A single reading is a hypothesis; three consistent readings are a measurement.

Loading diagram... Micrometer Reading and Calibration Check Workflow