Study guide
14.1 100-Hour, Annual & Progressive Engine Inspections
FAA Aviation Mechanic — Powerplant AMP
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Reciprocating Engine Theory & Construction
1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies
2 Chapter 2: Reciprocating Engine Dynamics & Valve Train
2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines
3 Chapter 3: Turbine Engine Theory & Compressors
3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems
4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards
4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)
5 Chapter 5: Engine Ignition & Starting Systems
5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems
6 Chapter 6: Propeller Fundamentals & Governors
6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems
7 Chapter 7: Propeller Maintenance & Turboprop Controls
7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control
8 Chapter 8: Engine Fuel Metering Systems
8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment
9 Chapter 9: Engine Lubrication Systems
9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting
10 Chapter 10: Induction, Supercharging & Engine Cooling
10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression
11 Chapter 11: Engine Electrical Systems
11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling
12 Chapter 12: Engine Instrument Systems
12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings
13 Chapter 13: Aircraft Engine Fuel Systems
13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC
14 Chapter 14: Engine Inspection, Records & Maintenance
14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts
15 Chapter 15: Engine Removal, Installation & Overhaul
15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures
16 Chapter 16: Engine Fire Protection & Exhaust Systems
16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers
14.1 100-Hour, Annual & Progressive Engine Inspections
Key Takeaways Explain This Topic AI
Under 14 CFR § 91.409(b), an aircraft carrying any person (other than a crewmember) for hire, or used to give flight instruction for hire in an aircraft the instructor provides, must have an annual or 100-hour inspection within each 100 hours of time in service; an appropriately rated A&P mechanic can perform the 100-hour and approve it for return to service.
Under 14 CFR § 91.409(a), unless paragraph (c) exempts it, no aircraft may be operated without an annual inspection within the preceding 12 calendar months (expiring at the end of the 12th month); for an individual mechanic, the annual takes an Inspection Authorization (IA), and repair stations and manufacturers approve under their own authority (14 CFR § 43.7).
The 100-hour inspection interval may be exceeded by up to 10 hours strictly to fly the aircraft to an inspection facility, but those overflown hours must be subtracted from the next 100-hour cycle; annual inspections have no overfly grace period and require an FAA Form 8130-7 Special Flight Permit.
The scope and detail of 100-hour and annual engine inspections are defined in 14 CFR Part 43 Appendix D, mandating rigorous checks of cylinder assemblies, crankcase seams, engine mounts, cowlings, exhaust systems (identifying black soot vs powdery white lead halide tracks), and control rigging cushion/spring-back.
Progressive inspection programs under 14 CFR § 91.409(d) break annual inspection requirements into scheduled, phased increments to minimize aircraft downtime for high-utilization commercial operators, provided the entire aircraft undergoes a complete inspection cycle within 12 calendar months.
Last updated: October 2026
14.1 100-Hour, Annual & Progressive Engine Inspections
Quick Answer: Aviation engine inspections are legally governed by 14 CFR Part 43 and 14 CFR Part 91 . An annual inspection is required every 12 calendar months for every aircraft except those § 91.409(c) exempts and, for an individual mechanic, must be performed by an Airframe and Powerplant (A&P) mechanic holding an Inspection Authorization (IA) (an appropriately rated repair station or the manufacturer may also perform it). A 100-hour inspection is required for aircraft carrying any person other than a crewmember for hire, or used for flight instruction for hire in an aircraft the instructor provides, and may be performed and approved by an appropriately rated A&P mechanic . A 100-hour inspection may be exceeded by up to 10 hours solely to reach an inspection facility (deducted from the next 100-hour window), whereas an annual has no grace period and requires an FAA Special Flight Permit (ferry permit) . Both inspections follow the rigorous scope of 14 CFR Part 43 Appendix D , requiring systematic checks of engine mounts, cowlings, exhaust soot signatures (black soot vs. white lead halide deposits), control rigging cushion ( 1/8-inch spring-back ), and disciplined pre- and post-inspection run-ups .
Regulatory Inspection Framework: 100-Hour, Annual & Progressive
Federal aviation regulations establish strict time-in-service and calendar-based thresholds for aircraft powerplant inspections to detect mechanical wear, thermal fatigue, and structural deterioration before in-flight failure occurs. +-----------------------------------------------------------------------------------------+
- | FAA POWERPLANT INSPECTION COMPARISON MATRIX |
- | |
- | INSPECTION TYPE | REGULATORY BASE | OPERATIONAL TRIGGER | RETURN TO SERVICE |
- | ---------------- | --------------- | ------------------------- | --------------------- |
- | Annual | 14 CFR § 91.409a| 12 calendar months | A&P with IA or |
- | | | (Unless 91.409c exempt) | Certificated Repair Stn|
- | 100-Hour | 14 CFR § 91.409b| 100 hours time in service | Certificated A&P |
- | | | (For hire / instruction) | Mechanic (or IA) |
- | Progressive | 14 CFR § 91.409d| Continuous phased schedule| A&P (routine stages) |
- | | | (Approved fleet plan) | IA (annual sign-off) |
- +-----------------------------------------------------------------------------------------+
- The Annual Inspection (14 CFR § 91.409(a))
Unless § 91.409(c) exempts it (special flight permit, experimental, light-sport, or provisional certificate, or an approved or progressive inspection program), no person may operate an aircraft unless it has had an annual inspection within the preceding 12 calendar months .
Calendar Calculation: The inspection expires at midnight on the last day of the twelfth month following the month of the previous inspection. For example, if an engine annual inspection is completed and signed off on September 3, 2025, it remains legally valid through midnight on September 30, 2026.
Sign-off Authority: For an individual mechanic, the annual must be performed by an A&P holding an Inspection Authorization (IA) under 14 CFR § 65.95(a)(2); an appropriately rated certificated repair station under 14 CFR Part 145, or the manufacturer, may also perform it. A mechanic without an IA cannot perform or approve an annual, and an uncertificated helper may not perform any required inspection (14 CFR § 43.3(d)).
Zero Grace Period & Ferry Permits: Unlike the 100-hour inspection, the annual inspection has no 10-hour overfly allowance . Once the calendar expiration date passes, the aircraft is grounded. To fly the aircraft to a maintenance facility for an inspection, the owner or technician must obtain an FAA Form 8130-7 Special Flight Permit (ferry permit) from the local Flight Standards District Office (FSDO) under 14 CFR § 21.197.
The 100-Hour Inspection (14 CFR § 91.409(b))
An aircraft must receive a 100-hour inspection if it is:
Carrying any person (other than a crewmember) for hire; or
Used by a person giving flight instruction for hire in an aircraft that person provides.
Sign-off Authority: A certificated A&P mechanic holding both Airframe and Powerplant ratings under 14 CFR Part 65 is fully authorized to conduct the inspection and approve the engine for return to service.
The 10-Hour Overfly Rule: 14 CFR § 91.409(b) allows the 100-hour limit to be exceeded by no more than 10 hours exclusively while en route to reach a maintenance facility where the inspection can be performed.
Accounting for Overflown Time: Any excess time flown beyond the 100-hour mark must be subtracted from the next 100-hour interval. For example, if an engine reaches 100 hours at 1,500 hours total time, and flies 6 additional hours to reach a maintenance base (completing the inspection at 1,506 hours), the subsequent 100-hour inspection becomes legally due at 1,600 hours total time (1,500 + 100), NOT 1,606 hours .
Interchangeability: A completed annual inspection satisfies the 100-hour requirement and resets the 100-hour clock. A 100-hour inspection counts as an annual only if a person authorized to perform annual inspections did it and entered it as an "annual" in the records (14 CFR § 91.409(a)), so a 100-hour by an A&P without an IA never substitutes for an annual.
Progressive Inspection Programs (14 CFR § 91.409(d))
For high-utilization commercial operators (such as flight schools, corporate flight departments, or commuter carriers), grounding an aircraft for several days to perform a complete annual inspection results in unacceptable revenue loss.
Under 14 CFR § 91.409(d), an operator may submit a written request to the FAA FSDO for approval of a progressive inspection schedule .
The comprehensive scope of an annual inspection is divided into sequential, manageable phases (such as four 50-hour cycles or six event-based stages).
The owner must provide a certificated mechanic holding an Inspection Authorization, a certificated airframe repair station, or the aircraft manufacturer to supervise or conduct the progressive inspection (14 CFR § 91.409(d)(1)).
Crucial Rule: The complete progressive program must ensure that the entire airframe, powerplant, propeller, and appliance installation undergoes a 100% complete inspection cycle within 12 calendar months .
Scope and Detail of Engine Inspections (14 CFR Part 43 Appendix D)
Under 14 CFR § 43.15, technicians performing an annual or 100-hour inspection must utilize a checklist conforming to the scope and detail set forth in 14 CFR Part 43 Appendix D . Technicians must systematically examine the following major powerplant subsystems: +-----------------------------------------------------------------------------------------+
- | 14 CFR PART 43 APPENDIX D ENGINE INSPECTION ITEMS |
- | |
- | 1. ENGINE SECTION --> Cleanliness, loose bolts, oil/fuel leaks, cracks |
- | 2. CYLINDERS --> Cooling fins, barrel studs, compression, cylinder head cracks |
- | 3. ENGINE MOUNT --> Tubular steel cracks, weld cluster integrity, rubber shock sag |
- | 4. COWLING/BAFFLES --> Fasteners, cracking, baffle seal orientation and condition |
- | 5. EXHAUST SYSTEM --> Pinhole cracks, thinning, slip joints, soot/lead halide tracks |
- | 6. ENGINE CONTROLS --> Full travel, stop contact, 1/8" cushion (spring-back) |
- | 7. FLUID PLUMBING --> Chafing, Adel clamp security, fire sleeve, line deterioration |
- +-----------------------------------------------------------------------------------------+
- 1. Cylinder Assemblies and Crankcase
Cooling Fins: Inspect for cracked, broken, or bent cylinder head and barrel cooling fins. Cracks across cooling fins act as severe stress risers; small cracks may be stop-drilled or contoured within manufacturer blend limits, but fin area loss directly diminishes cylinder cooling capacity.
Hold-Down Studs and Nuts: Check cylinder base hold-down nuts and crankcase thru-bolts for correct torque signatures, safety wire, and absence of oil weeping at the crankcase cylinder pad.
Crankcase Seams: Inspect crankcase spine parting lines and accessory case joints for structural cracking, fretting, or oil leaks. Fretting along the crankcase split line indicates loose thru-bolt torque and internal main bearing movement.
2. Engine Mounts and Vibration Isolators
Aircraft reciprocating engines are mounted to the firewall via a welded chrome-molybdenum (SAE 4130) tubular steel truss framework.
Welded Clusters: Thoroughly inspect all tube intersections and welded clusters using high-intensity light and 10x magnification. Welds represent the primary stress concentration zones where engine vibration and propeller gyroscopic forces induce fatigue cracking. Look for cracked paint, flaking primer, or rust bleeding, which indicate underlying metal fractures.
Tubular Members: Check tubes for denting, flattening, bent geometry, or internal corrosion.
Elastomeric Vibration Isolators (Shock Mounts): Inspect bonded rubber or synthetic elastomer Lord mounts for physical deterioration. Look for rubber swelling, softening, or gummy breakdown caused by petroleum oil and fuel contamination. Measure engine sag; permanent elastomeric compression causes engine droop, resulting in improper propeller spinner clearance and misalignment of cooling cowl baffles. Delamination between the rubber core and steel inner/outer sleeve requires immediate mount replacement.
3. Engine Cowling, Nacelles and Cooling Baffles
Cowling Structure: Inspect aluminum or fiberglass cowl panels for cracks radiating from fastener holes, loose or missing rivets, and fatigue cracking along intake lips.
Fasteners: Verify secure locking engagement of all Dzus, Camloc, and Tridair quarter-turn cowl fasteners. Worn receptacle springs allow cowlings to vibrate violently in flight, damaging airframe structures.
Cooling Baffles & Flexible Seals: Air-cooled piston engines rely on a pressure-cowling concept where incoming ram air is trapped above the cylinders and forced downward through cooling fins. Inspect aluminum baffle plates for fatigue cracking. Examine flexible silicone or fiberglass baffle seals: they must be pliable, free of tears, and oriented forward and upward so that high-pressure cooling air presses them firmly against the upper cowling cowl skin, preventing cooling air bypass.
4. Exhaust System Inspection & Soot Signature Diagnosis
Exhaust system failures represent an extreme in-flight hazard, capable of causing catastrophic in-flight engine fires or fatal carbon monoxide (CO) poisoning inside the cabin.
Soot Signature Physical Appearance Root Cause & Operational Hazard
Black Carbon Soot Velvety black powdery streak Fuel-rich exhaust escaping from loose slip joints, clamp junctions, or pinhole defects.
Gray or Powdery White Residue Crusty, chalky white or ash-gray streak Lead halide deposits from 100LL combustion escaping through high-temperature stress cracks. Critical failure indicator!
Bulging / Blistering Metal Localized ballooning or distortion Extreme internal metal thinning, hot spot erosion, or impending exhaust pipe burn-through.
Internal Flaking / Scaling Corrugated interior wall delamination Carburization and oxidation of stainless steel/Inconel mufflers; can dislodge and block tailpipe.
Lead Halide Deposits: Aviation gasoline (100LL) contains tetraethyl lead and ethylene dibromide. High-temperature exhaust leaks vaporize these compounds, depositing powdery white or ash-gray lead bromides and oxides directly along crack margins. Finding a white or gray streak on an exhaust pipe, flange, or inside a cabin heat shroud confirms an active structural exhaust crack . The shroud must be disassembled immediately, and cracked components must be replaced or repaired in accordance with FAA-approved technical data.
5. Engine Controls and Rigging (The Cushion / Spring-Back Rule)
Technicians must verify the mechanical rigging of all engine control linkages: throttle, mixture, propeller governor, carburetor heat, and alternate air.
Full Travel Verification: Controls must move smoothly through their entire range of travel without binding, chafing against structure, or excessive backlash.
The Mechanical Stop Cushion Principle: When rigging engine controls, the technician must adjust rod ends or cable stops so that the control lever on the engine (carburetor, fuel injector, or governor) hits its internal mechanical stop BEFORE the cockpit control lever reaches its travel limit in the quadrant .
1/8-Inch Spring-Back: When the cockpit control is moved firmly to its full forward or full aft position, the cockpit knob or lever must demonstrate approximately 1/8 inch of spring-back (cushion) away from the cockpit quadrant stop. This mechanical spring-back guarantees that airframe flexing during flight cannot pull the engine control lever away from its full-throttle, full-rich, or full-increase-RPM mechanical limit.
Pre-Inspection and Post-Inspection Engine Run-Up Protocols
Under FAA-H-8083-32B, systematic ground run-ups are mandatory bookends to the inspection process. ENGINE INSPECTION TIMELINE
- [ PRE-INSPECTION RUN-UP ] [ 100-HR / ANNUAL ] [ POST-INSPECTION RUN-UP ]
- Baseline engine health - Cowling removed - Operational leak check
- Magneto RPM drop & split - Compression test - Static RPM verification
- Idle RPM & mixture rise - Borescope evaluation - Idle speed & mixture final
- Instrument cross-check - Discrepancy corrective work - P-lead grounding check
- The Pre-Inspection Run-Up
Conducted prior to removing engine cowlings or performing maintenance. Its purpose is to evaluate the engine under stabilized operating temperature and uncover existing defects:
Magneto Check: Operate engine at specified magneto check speed (typically 1,700 to 1,800 RPM). Switch from BOTH to LEFT, note RPM drop, return to BOTH; switch to RIGHT, note RPM drop, return to BOTH. Verify that the RPM drop and the difference (split) between magnetos are within the manufacturer's limits (the FAA handbook describes a normal drop as even and generally about 25 to 75 RPM each).
Idle Mixture Rise Check: Retard throttle to idle. Slowly pull the cockpit mixture control toward IDLE CUTOFF while closely observing the tachometer. Just before the engine shuts off, the tachometer should exhibit a momentary RPM rise (the FAA handbook cites 10 to 50 RPM, depending on the installation):
Correct Setting: A rise within the installation's specified range indicates a properly adjusted, slightly rich idle mixture that delivers smooth throttle acceleration.
No RPM Rise (Immediate Drop): Indicates an excessively lean idle mixture (risk of engine stumbling or quitting during rapid throttle advance).
Excessive Rise (above the specified range): Indicates an excessively rich idle mixture (causes severe spark plug fouling and rough low-speed operation).
Auxiliary Systems: Verify carburetor heat drop (typically 50 to 100 RPM drop due to less dense warm air), suction gauge operation (4.5 to 5.5 in. Hg), and charging system output.
The Post-Inspection Run-Up
Conducted after completing all maintenance, torque checks, safety wiring, and reinstalling cowlings:
Oil Pressure Verification: Monitor oil pressure immediately upon engine start; oil pressure must indicate within 30 seconds in warm ambient conditions, or 60 seconds in sub-zero winter operations. If no pressure indicates within this timeframe, shut down immediately to prevent bearing seizure.
Operational Leak Check: Bring engine to operating temperature, shut down, and inspect oil filters, oil sump drain plugs, pushrod shroud tube seals, and fuel line B-nuts for active fluid seepage.
Magneto P-Lead Grounding Check: At low idle (the FAA handbook cites about 700 RPM, or the lowest speed the installation allows), momentarily turn the ignition key or toggle switches to OFF. The engine should completely quit firing. If the engine keeps firing, a magneto P-lead is open or disconnected , creating a lethal "hot magneto" condition that can cause the propeller to start the engine if rotated by hand.
Independent Prep Note
Independent FAA AMT Powerplant prep by ExamFinch. Not sponsored by or affiliated with the Federal Aviation Administration (FAA). Technical data compiled from FAA-H-8083-32B, FAA AC 43.13-1B, and 14 CFR Parts 21, 43, 65, and 91.