Study guide
9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture
FAA Aviation Mechanic — Powerplant AMP
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Reciprocating Engine Theory & Construction
1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies
2 Chapter 2: Reciprocating Engine Dynamics & Valve Train
2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines
3 Chapter 3: Turbine Engine Theory & Compressors
3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems
4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards
4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)
5 Chapter 5: Engine Ignition & Starting Systems
5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems
6 Chapter 6: Propeller Fundamentals & Governors
6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems
7 Chapter 7: Propeller Maintenance & Turboprop Controls
7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control
8 Chapter 8: Engine Fuel Metering Systems
8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment
9 Chapter 9: Engine Lubrication Systems
9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting
10 Chapter 10: Induction, Supercharging & Engine Cooling
10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression
11 Chapter 11: Engine Electrical Systems
11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling
12 Chapter 12: Engine Instrument Systems
12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings
13 Chapter 13: Aircraft Engine Fuel Systems
13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC
14 Chapter 14: Engine Inspection, Records & Maintenance
14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts
15 Chapter 15: Engine Removal, Installation & Overhaul
15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures
16 Chapter 16: Engine Fire Protection & Exhaust Systems
16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers
9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture
Key Takeaways Explain This Topic AI
Wet-sump systems store the entire oil supply in an integral sump attached directly beneath the engine crankcase, utilizing a single pressure pump and gravity drainage, ideal for compact horizontally opposed engines.
Dry-sump systems store oil in a remote external reservoir tank, using a pressure pump for supply and one or more engine-driven scavenge pumps to evacuate the crankcase sumps and return oil through the cooler to the tank.
Scavenge pumps must have a pumping capacity 1.5 to 2.0 times (50% to 100% greater than) the pressure pump to compensate for aerated, foaming scavenge oil and prevent crankcase flooding, viscous churning, and power loss.
Under the airframe airworthiness standards at 14 CFR §§ 23.1013 and 25.1013, each reciprocating-engine oil tank must have an expansion space of not less than the greater of 10% of the tank capacity or 0.5 gallon (2 quarts), and that space cannot be inadvertently filled during servicing.
A hopper (accelerated warm-up) tank inside a dry-sump reservoir isolates a small volume of oil around the pump pickup for rapid circulation and temperature rise during cold starts, while permitting gradual warming of the main tank reserve.
Last updated: September 2026
9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture
Quick Answer: Aviation reciprocating engines employ either wet-sump or dry-sump lubrication architectures. A wet-sump system stores its entire oil supply within an oil pan bolted directly to the bottom of the engine crankcase; it uses a single pressure pump to supply oil and relies on gravity drainage back to the sump. A dry-sump system stores oil in an external remote reservoir tank; it uses a pressure pump to feed the engine and scavenge pumps to evacuate oil from the lower crankcase. Scavenge pumps must have 1.5 to 2.0 times the capacity of the pressure pump to handle aerated, foaming oil and prevent crankcase flooding. Under 14 CFR Part 33 , dry-sump oil tanks must provide an expansion space of at least 10% of tank capacity or 0.5 gallon , whichever is greater, and often incorporate an internal hopper tank for accelerated engine warm-up.
Architectural Comparison: Wet-Sump vs. Dry-Sump Systems
The choice between wet-sump and dry-sump architectures is determined by engine horsepower, cylinder layout, cooling requirements, and flight attitude envelopes. +-------------------------------------------------------------------------+
- | LUBRICATION ARCHITECTURAL COMPARISON |
- | |
- | FEATURE WET-SUMP SYSTEM DRY-SUMP SYSTEM |
- | -------------------- ----------------------- ---------------------- |
- | Oil Storage Integral crankcase pan External remote tank |
- | Number of Pumps Single pressure pump Pressure + Scavenge |
- | Scavenge Ratio N/A (Gravity drain) 1.5x to 2.0x Pressure |
- | Weight & Complexity Lightweight, simple Heavier, more complex |
- | Oil Capacity Limited (6–12 quarts) High (4–10+ gallons) |
- | Oil Cooling Control Moderate (warm sump) Superior (remote cool) |
- | Inverted / Aerobatics Unports easily Sump pickups accommodate|
- | Primary Engines Horizontally opposed 4/6 High-output radials, |
- | (Lycoming O-360, etc.) turbines, aerobatic |
- +-------------------------------------------------------------------------+
- Wet-Sump System Operation
In a wet-sump configuration—standard on most horizontally opposed four- and six-cylinder general aviation engines (such as the Lycoming O-320, O-360, IO-540, and Continental O-200, IO-550):
The lubricating oil is contained completely within an aluminum or magnesium oil pan bolted directly to the bottom of the engine crankcase.
A submerged suction screen (finger strainer) rests near the bottom of the sump.
A single engine-driven positive displacement pressure pump draws oil up through the pickup tube and delivers it under pressure through the oil filter, vernatherm thermostatic bypass valve, and oil cooler to the main engine oil galleries.
After lubricating the crankshaft main bearings, connecting rod journals, camshaft lobes, and valve trains, the oil drains by gravity back down the crankcase walls into the sump.
Advantages: Outstanding mechanical simplicity, light weight, elimination of external oil lines, absence of scavenge pumps, and reduced risk of external hose rupture.
Disadvantages: Restricted oil capacity (typically 6 to 12 quarts); the oil remains close to hot cylinder barrels, running higher baseline temperatures; during prolonged uncoordinated flight or negative-G maneuvers, the oil pools away from the pickup tube ( unporting ), causing immediate loss of oil pressure.
Dry-Sump System Operation
In a dry-sump configuration—standard on large radial engines (such as the Pratt & Whitney R-985, R-1830, R-2800), inverted inline engines, aerobatic powerplants, and virtually all gas turbine engines:
Oil is stored in an external reservoir tank mounted on the engine firewall or aircraft structural airframe.
The engine crankcase sump is kept substantially "dry" (empty of standing oil) during operation.
The pressure pump draws cool oil from the bottom of the external tank and delivers it to the engine components.
Oil collects in small collector wells at the bottom of the crankcase (or turbine bearing cavities).
One or more high-capacity engine-driven scavenge pumps collect the scavenge oil and force it through the oil cooler and return line back into the external tank.
The Scavenge Pump Capacity Ratio: 1.5x to 2.0x
A universal rule of aircraft dry-sump lubrication design is that the scavenge pump capacity must always be significantly larger than the pressure pump capacity —typically 1.5 to 2.0 times (50% to 100% greater volume per minute) . Scavenge Volume Dynamics
- Pressure Pump Delivery Scavenge Pump Return
- [Dense Solid Liquid Oil] [Hot Aerated Foamy Fluid (Oil + Air)]
- 1.0 Volume 1.5 to 2.0 Volume
- | ^
- v |
- +---------------+ +---------------+
- | Engine Blocks | === Heavy Churning ===> | Lower Wells |
- +---------------+ Blowby & Splash Gas +---------------+
- Why Scavenge Pumps Must Over-Pump
There are two vital mechanical reasons for this design mandate:
Severe Fluid Aeration and Foaming: High-speed crankshaft rotation (2,500 to 2,700 RPM) flings oil off connecting rod journals, creating an atomized mist. Simultaneously, high-velocity blowby gases escaping past piston rings churn and whip the warm oil into a frothy, aerated mixture consisting of roughly 30% to 50% trapped air bubbles by volume. Because aerated oil is far less dense than solid liquid oil, the scavenge pump must displace a much larger fluid volume to return the same mass of oil to the tank.
Prevention of Crankcase Flooding and Viscous Drag: If the scavenge pump had only equal capacity to the pressure pump, aerated oil would gradually back up inside the crankcase. As oil levels rise, the rotating counterweights and crankshaft throws would strike the standing oil pool. This causes violent viscous churning , which:
Aerates the oil supply further, causing pump cavitation and sudden loss of oil pressure.
Generates massive friction that robs the engine of brake horsepower.
Drives oil temperatures past redline limits.
Forces oil past lower piston rings into combustion chambers, causing severe plug fouling, hydraulic lock, and cylinder head detonation.
In radial engines, allows oil to pool in lower cylinders, causing catastrophic liquid lock on startup.
Oil Tank Design Mandates (14 CFR Part 33 Requirements)
Dry-sump external oil tanks must comply with strict airworthiness certification criteria under Title 14 of the Code of Federal Regulations (14 CFR § 33.71) : +-------------------------------------------------------------------------+
- | 14 CFR § 33.71 OIL TANK MANDATES |
- | |
- | 1. EXPANSION SPACE --> >= 10% of tank capacity OR 0.5 gallon (2 qt), |
- | whichever is greater. |
- | 2. OVERFILL LOCKOUT --> Filler neck design must physically prevent |
- | inadvertent filling of the expansion space. |
- | 3. POSITIVE VENTING --> Must vent to crankcase or overboard to |
- | prevent internal pressure or vacuum lock. |
- | 4. BAFFLING --> Internal baffles prevent sloshing and |
- | unporting during climbs, dives, and slips. |
- +-------------------------------------------------------------------------+
- 1. Expansion Space Requirement
Every aircraft engine oil tank must incorporate an air cushion space above the liquid level: not less than 10% of the total tank volume or 0.5 gallon (2 U.S. quarts), whichever is greater .
Physical Function: When engine oil heats up from ambient ground temperature (e.g., 60°F) to operating temperature (e.g., 200°F), it undergoes significant thermal volumetric expansion. Furthermore, returning scavenge oil carries large volumes of entrained air bubbles that generate foaming. The expansion space accommodates this volumetric expansion and gives foam space to settle and collapse without forcing oil out the tank breather vent.
Overfilling Prevention: 14 CFR § 33.71 stipulates that the oil tank filler neck must be recessed into the tank or equipped with an internal overflow tube so that a technician servicing the tank cannot accidentally fill oil into the required expansion space when the aircraft is on level ground.
2. Tank Venting Requirements
As the scavenge pump returns aerated oil, the air bubbles release large volumes of air into the upper tank cavity. The oil tank must be positively vented to prevent dangerous internal pressure buildup. The vent line is almost universally connected to the engine crankcase breather system , ensuring that tank air is routed through the engine's internal oil-air separator before being discharged overboard through the breather tube.
The Hopper Tank Subsystem (Accelerated Warm-Up)
In large-capacity dry-sump oil tanks (such as an 8- to 12-gallon tank on a twin-engine transport or radial aircraft), circulating the entire oil volume immediately upon engine start presents a major operational challenge in cold weather:
Cold oil has high viscosity, flows sluggishly, and cannot lubricate tight clearances.
It would take 20 to 30 minutes of ground idling to bring 10 gallons of heavy mineral oil up to operating temperature, fouling spark plugs and causing excessive cylinder wear.
To solve this, aircraft engineers incorporate a hopper tank (also known as an accelerated warm-up well ) inside the main oil tank. Hopper Tank Architecture
- +-------------------------------------------------------+
- | EXTERNAL OIL TANK |
- | |
- | [ Main Tank Oil Reserve ] |
- | (Warms gradually) |
- | |
- | +----------------------------+ |
- | | HOPPER TANK | |
- | | (~1 to 1.5 Gallons) | |
- | | | |
- | Scavenge | Hot Scavenge Return | |
- | Return ===> | | | |
- | | v | |
- | | Rapid Warm-Up Zone | |
- | | | | |
- | | v | |
- | +-----[ Metering Holes ]-----+ |
- | | |
- +--------------------------|----------------------------+
- v
- To Engine Pressure Pump
- Mechanical Operation of the Hopper Tank
The hopper is an open-topped cylindrical metal chimney mounted centrally within the main oil tank directly above the engine suction outlet.
It segregates a small volume of oil—typically 1.0 to 1.5 gallons (4 to 6 quarts) —from the large surrounding oil mass.
The suction line to the engine pressure pump draws fluid directly from the bottom of the hopper cylinder.
Hot scavenge oil returning from the engine is discharged directly into the interior of the hopper, rather than into the main tank body.
During engine startup and warmup, the engine repeatedly recirculates and heats this small 1.5-gallon volume, bringing engine oil pressure and temperature into normal operating ranges within minutes.
As the oil in the hopper warms and expands, small calibrated metering holes in the base and lower sides of the hopper allow warm oil to circulate into the outer tank, gradually warming the main reserve.
Cold-Weather Oil Dilution Systems
In extreme arctic operations (temperatures well below 0°F / -18°C), straight mineral or heavy aviation oils congeal into a semi-solid jelly. Under these conditions, electric starter motors cannot turn the crankshaft, or the starter shears its drive gear.
System Operation (Historical and Bush Flying Protocol)
Legacy reciprocating powerplants operating in arctic environments were equipped with an oil dilution system :
Prior to shutting down the engine after a flight in freezing temperatures, the pilot activates an electric cockpit dilution switch.
A solenoid-actuated valve opens a line connecting the fuel pressure manifold directly to the engine oil circulating loop at the hopper tank inlet.
Aviation gasoline (100LL) is metered into the hot circulating oil for 2 to 4 minutes while idling at low RPM.
The gasoline mixes thoroughly with the lubricating oil in the hopper tank, lowering its viscosity to a thin fluid consistency.
The engine is then shut down with thinned, diluted oil coating all bearing surfaces and sitting in the hopper well.
The Morning Start: The following morning, the engine cranks freely because the oil is thin. As the engine warms up to operating temperatures (above 160°F / 71°C), the volatile aviation gasoline evaporates completely out of the hot oil and vents harmlessly overboard through the crankcase breather tube, restoring the lubricating oil to its full high-temperature viscosity rating.
Independent Prep Note
Independent FAA AMT Powerplant prep by ExamFinch. Not sponsored by or affiliated with the Federal Aviation Administration (FAA). Technical data compiled from FAA-H-8083-32B, FAA AC 43.13-1B, and 14 CFR Parts 33, 43, and 65.