Study guide

8.1 Float-Type Carburetors & Internal Operating Systems

FAA Aviation Mechanic — Powerplant AMP

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Reciprocating Engine Theory & Construction

1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies

2 Chapter 2: Reciprocating Engine Dynamics & Valve Train

2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines

3 Chapter 3: Turbine Engine Theory & Compressors

3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems

4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards

4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)

5 Chapter 5: Engine Ignition & Starting Systems

5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems

6 Chapter 6: Propeller Fundamentals & Governors

6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems

7 Chapter 7: Propeller Maintenance & Turboprop Controls

7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control

8 Chapter 8: Engine Fuel Metering Systems

8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment

9 Chapter 9: Engine Lubrication Systems

9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting

10 Chapter 10: Induction, Supercharging & Engine Cooling

10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression

11 Chapter 11: Engine Electrical Systems

11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling

12 Chapter 12: Engine Instrument Systems

12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings

13 Chapter 13: Aircraft Engine Fuel Systems

13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC

14 Chapter 14: Engine Inspection, Records & Maintenance

14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts

15 Chapter 15: Engine Removal, Installation & Overhaul

15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures

16 Chapter 16: Engine Fire Protection & Exhaust Systems

16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers

8.1 Float-Type Carburetors & Internal Operating Systems

Key Takeaways Explain This Topic AI

A float-type carburetor utilizes Bernoulli's principle to meter fuel by creating a low-pressure area in the venturi throat, establishing a metering force between atmospheric/float bowl pressure and venturi suction.

The float chamber maintains a constant fuel level approximately 1/8 inch below the main discharge nozzle opening; float level is mechanically adjusted by varying the thickness of shims under the float needle valve seat.

The air bleed system introduces atmospheric air into the main discharge nozzle to break fuel surface tension, emulsify the fuel-air charge for enhanced atomization, and prevent the mixture from becoming excessively rich at high airflows.

The idle system functions only when the throttle valve is nearly closed, utilizing high manifold vacuum beneath the butterfly to draw fuel through dedicated idle discharge ports located at the edge of the throttle plate.

The accelerating system provides a momentary rich charge via a delayed-action spring and piston/diaphragm to prevent lean hesitation upon rapid throttle opening, while the economizer/power enrichment system enriches the mixture above ~65-75% power to prevent detonation and provide cylinder cooling.

Last updated: September 2026

8.1 Float-Type Carburetors & Internal Operating Systems

Quick Answer: A float-type carburetor meters fuel proportionally to engine mass airflow using Bernoulli's principle . As incoming air accelerates through a restricted venturi , its static pressure drops, creating venturi suction . The differential pressure between the ambient-pressure float chamber and the low-pressure venturi throat forces fuel through the main metering jet and out the main discharge nozzle . To operate across all engine regimes, the carburetor integrates six distinct subsystems: the float mechanism (maintains fuel level 1/8" below nozzle via needle seat shims), main metering system , air bleed system (emulsifies fuel and prevents high-RPM over-enrichment), idle system (draws fuel via manifold vacuum at closed throttle), accelerating system (delayed-action spring prevents lean hesitation), and power enrichment / economizer system (supplies extra fuel above ~65–75% power for detonation suppression and internal cylinder cooling).

The Aerodynamic Foundation: Bernoulli's Principle & Venturi Suction

In aircraft reciprocating engines, the fundamental objective of any fuel metering device is to deliver the correct mass of fuel in proportion to the mass of induction air entering the cylinders across all operating regimes—from low idle through full takeoff power. Venturi Aerodynamics & Fuel Metering

  • High Pressure Air Inlet Low Pressure Throat Intake to Engine
  • ===============================+ +=====================
  • -> Velocity: Low | High Velocity | --> Velocity: Med
  • -> Static Pressure: High | Low Static Pressure | --> Pressure: Recovers
  • ------------------------------+ +---------------------
  • | Main Discharge Nozzle |
  • | | | |
  • | | | |
  • | |_| |
  • ------------------------------+ +---------------------
  • ===============================+ +=====================
  • Venturi Suction
  • The Venturi Principle

A float-type carburetor operates directly upon Bernoulli's Principle of fluid dynamics , which governs incompressible and subsonic compressible fluid flow: P static + 1 2 ρ V 2 = P total = Constant P_{\text{static}} + \frac{1}{2} \rho V^2 = P_{\text{total}} = \text{Constant} P static ​ + 2 1 ​ ρ V 2 = P total ​ = Constant

When induction air is drawn through the carburetor barrel by the downward suction strokes of the engine pistons, it encounters a smooth constriction called the venturi :

Conservation of Mass (Continuity Equation): As the cross-sectional area decreases at the venturi throat ( A 1 V 1 = A 2 V 2 A_1 V_1 = A_2 V_2 A 1 ​ V 1 ​ = A 2 ​ V 2 ​ ), air velocity must increase.

Static Pressure Drop: According to Bernoulli's equation, an increase in fluid kinetic energy (velocity squared) must be accompanied by a simultaneous, proportional decrease in static fluid pressure.

Venturi Suction: The static pressure inside the venturi throat drops well below ambient atmospheric pressure. This depression is commonly referred to in aviation maintenance as venturi suction .

The Metering Force: The fuel in the float chamber is vented to ambient atmospheric pressure (or carburetor inlet impact air pressure in balanced systems). The difference in pressure between the higher ambient pressure in the float chamber and the lower static pressure in the venturi throat creates the fuel metering force that drives fuel out of the discharge nozzle and into the passing airstream.

The Float Chamber & Float Level Adjustment

The float chamber acts as a constant-head fuel reservoir supplying fuel to the metering circuits. Because the metering force depends on the pressure differential between the float chamber and the venturi throat, any unintended fluctuation in the liquid fuel level inside the chamber will alter the air-fuel ratio. Float Mechanism & Needle Seat Assembly

  • Fuel Inlet Line (from Engine-Driven Pump / Gravity)
  • |
  • v
  • [ Needle Valve Seat ]

[ Metal Shims ] <----- Adjusts Float Level!

  • [ Needle Valve ]
  • ||
  • +--------------++--------------+
  • | |
  • | Brass / Composite Float |
  • | |
  • +------------------------------+
  • ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Fuel Level (1/8" below nozzle)
  • Mechanical Operation

Float Assembly: Constructed from soldered lightweight brass or molded closed-cell synthetic composite material. The float is hinged inside the chamber and mechanically linked to a hardened stainless steel or Viton-tipped needle valve .

Needle Valve and Seat: As fuel enters the float bowl from the aircraft fuel pump (or gravity tank), the float rises. When fuel reaches the calibrated level, the float lever drives the needle valve firmly into its hardened stationary seat, arresting incoming fuel flow.

Dynamic Equilibrium: As the engine consumes fuel, the float drops slightly, opening the needle valve just enough to admit replacement fuel at the exact rate of engine consumption.

The 1/8-Inch Rule & Fuel Level Rigging

Standard Fuel Level Height: The liquid fuel level in the float chamber must be maintained at a precise height—typically 1/8 inch (0.125 in / 3.2 mm) below the lip of the main discharge nozzle opening .

Consequences of Excessive Fuel Level: If the fuel level is too high, fuel will spill or percolate out of the discharge nozzle when the aircraft is parked, idling, or in turbulent flight. This causes an excessively rich fuel-air mixture, heavy black exhaust smoke, fouled spark plugs, unburned fuel waste, and extreme engine fire hazard.

Consequences of Insufficient Fuel Level: If the fuel level is too low, excessive venturi suction is required to lift the fuel column before discharge can begin. This causes an excessively lean fuel-air mixture, engine stumbling upon throttle advancement, high cylinder head temperatures, and detonation.

Maintenance Adjustment Protocol (FAA-H-8083-32B): Float level cannot be adjusted by bending the float lever arm casually in the field unless specifically authorized by the manufacturer overhaul manual. On standard aviation float carburetors (such as the Stromberg / Bendix MA-3 and MA-4-5 series), float level is precisely adjusted by altering the thickness of the copper or fiber gasket shims installed directly beneath the needle valve seat assembly :

Adding shims (thicker washer pack): Moves the needle seat downward relative to the bowl, seating the needle earlier and lowering the fuel level .

Removing shims (thinner washer pack): Moves the needle seat upward, allowing the float to rise higher before seating, thereby raising the fuel level .

The Main Metering System

The main metering system supplies and regulates fuel flow during cruising, high-speed, and climbing flight (all power settings above approximately 1,000 to 1,200 RPM). It consists of three primary components: Main Metering System Schematic

  • Air Bleed Inlet (Atmospheric / Filtered Air)
  • |
  • v
  • [ Air Bleed Well ]
  • |
  • v (Air Bubbles)
  • [ Float Bowl ] ---> [ Main Metering Jet ] ===> [ Main Discharge Nozzle ] ===> Venturi Throat

Main Metering Jet: A precision-calibrated restriction or orifice threaded into the fuel passage between the float bowl and the discharge nozzle. It meters the maximum quantity of fuel that can flow to the main nozzle at a given venturi suction.

Main Discharge Nozzle: A hollow brass or bronze tube extending from the metering well into the center of the venturi throat. The tip of the nozzle is angled downstream into the highest-velocity airstream to optimize suction and shear the fuel into droplets.

Main Air Bleed Well: Surrounds the discharge nozzle assembly, delivering calibrated aerating air into the fuel column before it exits into the venturi.

The Air Bleed System: Physics of Emulsification

A liquid fuel jet operating alone in an air stream suffers from two inherent physical limitations that make precise air-fuel metering impossible:

The Problem of Surface Tension and Droplet Size

Raw aviation gasoline possesses significant cohesion and surface tension . If solid gasoline is discharged directly from a plain open tube into an airstream, the fuel leaves as large liquid slugs or heavy droplets. Large fuel droplets cannot vaporize completely in the brief fraction of a second before entering the combustion chamber, resulting in incomplete combustion, poor power output, and severe cylinder-to-cylinder fuel imbalance.

The Natural Over-Enrichment Characteristic

As engine RPM and airflow increase, fluid dynamics causes the mass flow rate of liquid fuel through a plain orifice to increase at a faster rate than the mass flow rate of air through the venturi. Without compensation, a plain jet carburetor would produce an increasingly rich fuel-air mixture as engine power increases—running lean at low cruise and dangerously rich at full power. Air Bleed Operating Mechanism Inside Discharge Well

  • Ambient Air In
  • |
  • v
  • +---------------+
  • | Air Bleed Jet |
  • +---------------+
  • |
  • ================+================ Discharge Nozzle Outer Wall

: . . . . . . . . . . :

  • : [Air Bubbles Emulsify Fuel] : ===> Emulsion (Fuel + Air)
  • : . . . . . . . . . . : Exits into Low-Pressure Venturi
  • ================+================
  • ^
  • | Liquid Fuel from Main Metering Jet
  • The Triple Function of the Air Bleed (FAA-H-8083-32B)

The air bleed system introduces a controlled, small quantity of ambient air into the fuel stream just below the liquid level inside the discharge nozzle:

Emulsification & Surface Tension Breakdown: The tiny air bubbles break the cohesive surface tension of the fuel, churning it into a frothy emulsion (a lightweight fuel-air foam) . When this emulsion exits the nozzle into the low-pressure venturi, the air bubbles expand explosively, shattering the fuel into microscopic vaporized droplets.

Prevents Fuel Dribble at Low Speeds: By aerating the fuel column, the air bleed reduces the effective density of the fluid in the nozzle. This allows a smooth, steady discharge to begin at lower venturi air velocities without raw liquid dribbling out the nozzle lip.

Corrects High-Speed Mixture Enrichment: As venturi suction increases at high airflow, the air bleed draws progressively larger volumes of air relative to liquid fuel. This automatic aeration effectively leans the discharge mixture back to the desired constant ratio, flattening the fuel-air curve across the entire cruise operating spectrum.

The Idle System: Low-Speed Manifold Suction

When an aircraft engine is throttled back to idle speed (typically 600 to 800 RPM), the throttle butterfly valve is almost completely closed. In this condition, air velocity through the venturi throat is virtually zero, generating insufficient venturi suction to draw any fuel from the main discharge nozzle . Idle Metering System Geometry

  • Intake Manifold (Extreme Suction: 15–20" Hg Vac)
  • Carburetor Barrel |
  • =======================================|======================================
  • +--v--+ Primary Idle Discharge Hole
  • Throttle ===> | / | | (Directly Exposed to Manifold Suction)
  • Butterfly |/ | |
  • +--+--+ Secondary Off-Idle Air Bleed / Holes
  • =======================================|======================================
  • ^
  • [ Idle Passage ]
  • ^
  • [ Idle Air Bleed Jet ]
  • ^
  • [ Idle Metering Jet ]
  • ^
  • [ Float Chamber ]
  • Mechanics of the Idle Circuit

Manifold Vacuum as the Driving Force: Although pressure above the throttle butterfly is near atmospheric, the downward-moving pistons create an extreme low-pressure zone (high vacuum: 15 to 20 inches of mercury below atmospheric) immediately downstream of the closed throttle plate.

Idle Discharge Holes: The idle system bypasses the venturi entirely. An internal passage leads from the float chamber through a calibrated idle metering jet to one or more small discharge holes drilled directly into the carburetor barrel wall immediately adjacent to the edge of the throttle butterfly .

Primary Idle Port: When the throttle is fully closed against its idle speed stop screw, the primary idle discharge hole is exposed directly to the high manifold suction, drawing fuel out in a steady spray.

Idle Air Bleed: A small calibrated air bleed admits air into the idle fuel passage to emulsify the idle fuel and allow precise adjustment via the idle mixture adjusting screw .

Off-Idle Transition Holes: Directly below the primary idle port are one or two secondary transition holes. As the pilot slowly opens the throttle, the edge of the butterfly sweeps past these secondary holes, exposing them to manifold suction. This uncovers additional fuel orifices sequentially, ensuring a smooth, uninterrupted transition from idle to the main metering system without flat spots or engine stalling.

Idle Cutoff (ICO): The idle circuit incorporates a mechanical cutoff valve. When the pilot pulls the mixture control to the full-aft IDLE CUTOFF position, this valve mechanically blocks the idle fuel passage completely. With no fuel reaching the idle ports, the engine starves and cleanly ceases firing within seconds.

The Accelerating System: Preventing Lean Hesitation

When the pilot abruptly opens the throttle from idle or cruise to full power, a fundamental physics challenge arises:

The Acceleration Stumble Phenomenon

Air is a lightweight, low-inertia gas that responds instantly to an opening throttle plate, rushing into the intake manifold in massive volume. Aviation gasoline, however, is a dense liquid with significant mass and inertia. Liquid fuel cannot accelerate instantly through the main metering jet and discharge nozzle. This momentary lag causes a temporary surge of excess air with insufficient fuel—a condition known as lean hesitation or acceleration stumble —which can cause the engine to backfire, sputter, or stall completely at the critical moment of takeoff or go-around. Piston-Type Accelerating Pump Operation

  • Throttle Linkage Shaft
  • |
  • v (Pushed Downward on Rapid Throttle Advance)
  • [ Actuating Rod ]
  • |
  • [ DELAYED ACTION SPRING ] <----- Absorbs Instant Impact;

| Steadily Forces Piston Down!

  • v
  • [ Pump Piston ]
  • |
  • v (Discharges Fuel Under Pressure)
  • [ Float Bowl ] | ===> [ Outlet Check Valve Opens ]
  • | | |
  • +---> [ Inlet Check Valve Closes ] v
  • [ Accelerating Discharge Jet ]
  • (Sprays Solid Fuel into Venturi)
  • The Delayed-Action Spring Mechanism

To prevent this hazard, float carburetors incorporate an accelerating pump system (piston or diaphragm type) mechanically linked to the throttle control shaft:

Inlet Check Valve: During steady-state operation, fuel from the float bowl fills the accelerating pump cylinder through a one-way ball inlet check valve.

Throttle Advance: When the throttle is rapidly advanced, the mechanical linkage drives an actuating rod downward.

The Delayed-Action Spring: Crucially, the actuating rod does not strike the pump piston rigidly. Instead, it compresses a calibrated delayed-action coil spring positioned between the actuating rod and the piston head.

Smooth Fuel Discharge: The compressed spring steadily and progressively forces the piston down through the fuel cylinder over a period of several seconds . The rising hydraulic pressure instantly snaps the inlet check valve shut and forces the spring-loaded outlet check valve open.

Sustained Fuel Enrichment: Fuel is forced through an auxiliary accelerating discharge nozzle directly into the carburetor air stream. The delayed-action spring ensures a continuous, sustained stream of rich fuel that lasts long enough for the main metering system to catch up with the high-velocity airflow, eliminating all trace of hesitation.

Siphon Prevention: During normal cruise flight, the outlet check valve is held tightly shut by its calibrated spring, preventing high venturi suction from siphoning fuel out of the accelerating pump reservoir.

The Power Enrichment / Economizer System

During normal cruise flight between 55% and 65% power, an aircraft engine operates most efficiently on a lean "best economy" fuel-air mixture (approximately 16:1 by weight). However, when the engine is operated at high power settings—such as takeoff, maximum continuous power, or climb (above approximately 65% to 75% power)—a lean mixture creates extreme operational hazards:

Why Power Enrichment is Mandatory

Thermal Dissipation: At high power, the heat generated inside the combustion chamber exceeds the cooling capacity of the cylinder fins and engine oil alone. Extra fuel must be injected into the cylinder. The vaporization of this excess fuel absorbs immense latent heat, internally cooling the cylinder heads and exhaust valves.

Detonation Suppression: High manifold pressure and temperature dramatically reduce the combustion detonation margin. A rich fuel-air mixture (approximately 12:1 by weight) burns cooler and stabilizes the flame front, completely suppressing destructive high-power detonation. Mechanical Needle-Type Economizer Operation

  • Throttle Shaft at ~70% Travel
  • |
  • v (Mechanical Cam Engages)
  • [ Actuating Link ]
  • |
  • v
  • [ Spring-Loaded Economizer ]
  • [ Needle Valve ]
  • |
  • v (Pushed Off Seat at High Throttle)
  • [ Float Bowl Fuel ] ====================================> [ Main Well / Aux Jet ]
  • (Supplies Extra Fuel!)
  • Types of Economizer Systems

Despite the name "economizer," this system is truly a power-enrichment system —it allows the carburetor to run economically lean during normal cruise, and enriches only when high power demands it. Three principal designs exist in aviation:

Economizer Type Operating Mechanism Typical Application

Needle-Type (Mechanical) A spring-loaded needle valve is mechanically opened by a cam on the throttle shaft as the throttle passes ~65–75% travel. Opens an auxiliary fuel metering jet in parallel with the main jet. Stromberg / Marvel-Schebler MA series carburetors.

Back-Suction (Pneumatic) Applies controlled venturi/manifold suction to the top of the sealed float chamber during cruise, slightly lowering float bowl pressure to lean the mixture. At full throttle, the passage vents to atmospheric pressure, equalizing bowl pressure and instantly enriching fuel flow. Continental / Lycoming small aircraft carburetors.

Pressure-Operated (Diaphragm) An internal spring-loaded diaphragm senses intake manifold pressure. When manifold pressure exceeds a calibrated threshold, the diaphragm overcomes spring tension to unseat a power enrichment valve. Large radial engines and turbocharged reciprocating engines.

Summary of Float Carburetor Subsystems

  • Subsystem Primary Driving Force Active Operating Regime Key Components
  • Float Mechanism Fuel buoyancy & gravity All engine regimes Brass/composite float, needle valve, seat shims

Main Metering Venturi depression (Bernoulli) Cruise, climb, takeoff (>1,000 RPM) Main metering jet, main discharge nozzle, well

Air Bleed Atmospheric air pressure Off-idle through full power Air bleed jet, diffuser well, emulsion holes

Idle System Downstream manifold vacuum Low idle (600–900 RPM) Idle jet, idle air bleed, primary/off-idle ports, ICO

Accelerating Mechanical throttle linkage Rapid throttle advancement Pump piston/diaphragm, delayed-action spring, checks

Power Enrichment Throttle cam or manifold pressure High power (>65–75% throttle) Economizer needle valve, aux jet, bowl suction port

Independent Prep Note

Independent FAA AMT Powerplant prep by ExamFinch. Not sponsored by or affiliated with the Federal Aviation Administration (FAA). Technical data compiled from FAA-H-8083-32B, FAA AC 43.13-1B, and manufacturer maintenance specifications.

Loading diagram... Float-Type Carburetor Internal Operating Architecture & Fuel Flow Paths