Study guide
5.5 Solid-State & Electronic Ignition Systems
FAA Aviation Mechanic — Powerplant AMP
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Reciprocating Engine Theory & Construction
1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies
2 Chapter 2: Reciprocating Engine Dynamics & Valve Train
2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines
3 Chapter 3: Turbine Engine Theory & Compressors
3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems
4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards
4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)
5 Chapter 5: Engine Ignition & Starting Systems
5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems
6 Chapter 6: Propeller Fundamentals & Governors
6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems
7 Chapter 7: Propeller Maintenance & Turboprop Controls
7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control
8 Chapter 8: Engine Fuel Metering Systems
8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment
9 Chapter 9: Engine Lubrication Systems
9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting
10 Chapter 10: Induction, Supercharging & Engine Cooling
10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression
11 Chapter 11: Engine Electrical Systems
11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling
12 Chapter 12: Engine Instrument Systems
12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings
13 Chapter 13: Aircraft Engine Fuel Systems
13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC
14 Chapter 14: Engine Inspection, Records & Maintenance
14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts
15 Chapter 15: Engine Removal, Installation & Overhaul
15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures
16 Chapter 16: Engine Fire Protection & Exhaust Systems
16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers
5.5 Solid-State & Electronic Ignition Systems
Key Takeaways Explain This Topic AI
A solid-state electronic ignition system replaces the magneto's fixed mechanical E-gap timing with crankshaft-position and manifold-pressure sensing, so spark timing varies continuously with engine speed and load instead of being locked at a single advance.
FAA-H-8083-32B describes the PowerLink FADEC as a solid-state digital electronic ignition and sequential port fuel injection system in which the electronic control units establish ignition timing that cannot be manually adjusted.
In the PowerLink architecture each electronic control unit carries two coil packs and controls the spark for two cylinders, and both control channels must fire for both plugs in a given cylinder to spark on the compression stroke.
Electronic ignition depends on aircraft electrical power, so a certificated installation provides a secondary power source or retains one magneto; a magneto, by contrast, generates its own current and runs with the bus dead.
Because a capacitor-discharge or coil-pack ignition stores lethal energy and can fire from a stationary crankshaft on command, the safing procedure is to remove electrical power and follow the manufacturer's discharge wait before touching the harness or propeller.
Last updated: October 2026
5.5 Solid-State & Electronic Ignition Systems
Quick Answer: A solid-state electronic ignition system fires the spark plugs from transistor-switched coil packs under the control of an electronic control unit (ECU) instead of from a self-generating magneto. FAA-H-8083-32B describes the PowerLink FADEC as "a solid-state digital electronic ignition and electronic sequential port fuel injection system" whose microprocessor controls ignition timing for engine starting and varies timing with respect to engine speed and manifold pressure , and it states plainly that engine ignition timing is established by the ECUs and cannot be manually adjusted . In that architecture, two coil packs sit in the upper portion of each ECU, and each ECU controls the ignition spark for two engine cylinders ; for both plugs in a cylinder to fire on the compression stroke, both control channels must fire their coil packs . The trade is timing precision for electrical dependency, which is why certificated installations provide a secondary power source (SPS) or retain one magneto.
Why the ACS Lists This Separately From Magnetos and FADEC
The Powerplant ACS ignition subject enumerates magneto theory, spark plug theory, shower of sparks and impulse coupling, the three magneto circuits, solid-state ignition systems , digital engine control modules, engine starters, magneto components, and turbine ignition. Solid-state ignition gets its own line because it is neither a magneto variant nor simply "the FADEC." It is the family of systems that fire a conventional reciprocating-engine spark plug using electronics, and it shows up on the test as a comparison against the magneto system you have already studied.
The Core Limitation of a Magneto That Electronics Solve
A high-tension magneto is an elegant machine with one fixed constraint: its spark timing is mechanical and essentially fixed . Breaker points are set to open at the E-gap position, the magneto is then timed to the engine at a single crankshaft angle published on the engine data plate, and that advance is what the engine gets at every RPM and every manifold pressure.
That single fixed advance is a compromise:
At high RPM , the flame front has less real time to cross the chamber for the same number of crankshaft degrees, so the engine would benefit from more advance.
At low manifold pressure (high altitude cruise, or part throttle), the charge is less dense, flame speed is slower, and again more advance would help.
At high manifold pressure and low RPM — the classic overboost condition — the same fixed advance puts peak pressure early and pushes the engine toward detonation, which is why the detonation chapter treats high MAP with low RPM as a primary cause.
An electronic system measures the conditions and moves the timing. FAA-H-8083-32B's description of the PowerLink system is explicit: the microprocessor-based system controls ignition timing for engine starting and varies timing with respect to engine speed and manifold pressure , and the spark energy is also varied with respect to engine load .
Architecture of a Solid-State Ignition System SOLID-STATE ELECTRONIC IGNITION SIGNAL PATH
- [ Crankshaft position / speed sensor ] --+
- [ Manifold pressure (MAP) sensor ] --+
- [ Manifold air temperature sensor ] --+--> [ ELECTRONIC CONTROL UNIT ]
- [ Cylinder head temperature sensor ] --+ | (control channel)
- [ Fuel pressure sensor ] --+ |
- v
- [ Transistor switching stage ]
- |
- v
- [ COIL PACK (2 towers) ]
- | |
- positive | | negative
- polarity v v polarity
- [ Plug, cyl A ] [ Plug, cyl B ]
Sensing. FAA-H-8083-32B lists the PowerLink sensor set as a speed sensor that monitors engine speed and crank position, fuel pressure sensors, manifold pressure sensors, manifold air temperature (MAT) sensors, CHT sensors, and EGT sensors , and notes that all critical sensors are dually redundant, with one sensor of each pair connected to control channels in different ECUs . If both sensors of a redundant pair fail, synthetic software default values are used.
Switching and coils. Where a magneto opens breaker points to collapse a primary field, an electronic system switches primary current with a power transistor. The energy then steps up through a coil pack rather than through a magneto's secondary winding and distributor rotor. There is no distributor block, no rotor, no breaker points, and no capacitor to replace.
Wasted-spark polarity pairing. In the PowerLink layout, each coil pack generates a high-voltage pulse for two spark plug towers; one tower fires a positive-polarity pulse and the other fires a negative-polarity pulse . Each ECU controls the spark for two cylinders, and each coil pack has a spark plug from each of the two cylinders controlled by that ECU . The redundancy consequence is the exam point: for both spark plugs in a given cylinder to fire on the compression stroke, both control channels must fire their coil packs.
What Replaces the Magneto Check
The magneto check exists to prove that each independent ignition system can run the engine and that each P-lead grounds. An electronic system needs the equivalent proof, delivered differently.
Magneto System Solid-State Electronic System
Switch BOTH → L → BOTH → R → BOTH, observe RPM drop within limits Run a manufacturer-specified channel check that inhibits one ECU channel at a time and observes the same kind of RPM or power indication
Switch momentarily to OFF at idle to prove both P-leads ground Verify the system shuts down cleanly on the master or ignition switch, and that no fault code indicates a stuck output
No RPM drop on one magneto = the other magneto's P-lead is not grounding (hot magneto) Health Status Annunciator (HSA) lights and stored fault codes report channel, sensor, and coil faults
Internal timing set with a timing light or buzz box; timing to engine set by rotating the magneto Timing is established by the ECUs and cannot be manually adjusted — there is nothing to set with a timing light
Breaker points, capacitor, distributor block, rotor are scheduled replacement items Coil packs, harness, sensors, and ECUs are replaced as units; software configuration is a controlled item
FAA-H-8083-32B notes that the PowerLink system performs self-diagnostics to determine overall system status and conveys this information to the pilot by various indicators on the health status annunciator (HSA) panel . That annunciator, not a tachometer needle, is the primary health readout.
The Electrical Dependency Problem
This is the single most important safety difference and the one most likely to be tested.
A magneto is a self-contained engine-driven alternating current generator . Section 5.1 established that it produces its ignition energy from engine rotation alone, completely independent of the aircraft battery or DC electrical bus . Pull every breaker, disconnect the battery, and a magneto engine keeps running.
A solid-state ignition system has no such independence. Remove electrical power and the ECU cannot switch the coil packs. Certificated installations therefore address the problem in one of two ways:
A secondary power source. FAA-H-8083-32B states that in the PowerLink system, in the event of loss of primary aircraft-supplied power, the engine controls continue to operate using a secondary power source (SPS) . The SPS is part of the powerplant installation and is a scheduled inspection item; its capacity check is not optional.
A hybrid installation. Many field-approved and supplemental type certificate installations replace one magneto with an electronic ignition unit and retain the other magneto. The engine keeps a self-powered ignition path, while one cylinder plug per cylinder gets variable timing. In a hybrid installation the ground run still includes a conventional check of the remaining magneto, and the technician must know which plug in each cylinder is fired by which system before troubleshooting a rough mag check.
Caution
A solid-state ignition system is not "safe" merely because there is no magneto. The coil packs and any capacitor-discharge stage store energy capable of delivering a lethal shock, and an ECU with power applied can command a spark with the crankshaft stationary. Before touching the high-voltage harness, the plugs, or the propeller, remove electrical power at the master and the battery, pull the applicable circuit breakers, and observe the manufacturer's discharge wait time. The turbine-ignition rule of Section 5.4 — de-energize, wait, then ground the lead before touching it — applies here for the same physical reason.
Failure Modes and Troubleshooting
Symptom: rough running that worsens with altitude. A sensor feeding altitude-dependent data, most often the manifold pressure sensor, is drifting. Because timing is scheduled against MAP, a MAP error becomes a timing error that only shows up where the schedule is steep.
Symptom: hard starting with normal cranking speed. The crankshaft position sensor gap or signal quality is suspect. Without a valid position signal the ECU has no reference for the start timing schedule, and unlike an impulse-coupled magneto there is no mechanical fallback that produces a retarded starting spark.
Symptom: one cylinder dead, both plugs. In the paired-coil architecture, both plugs in a cylinder require both control channels to fire. A single failed channel can therefore produce a symptom that looks nothing like a single fouled plug.
Symptom: intermittent faults that clear on the ground. Download the stored fault history rather than chasing the symptom. Self-diagnostic storage is the diagnostic tool the magneto never had, and the manufacturer's data specifies which codes are dispatch-limiting.
What you do not do. Do not attempt to "retime" an ECU-controlled system with a timing light, do not substitute non-approved spark plugs or a non-approved harness because the resistance and shielding are part of the approved configuration, and do not sign off a software or configuration change without the record entry the manufacturer's data requires.
Comparison Summary: Three Ignition Families on One Airframe
Characteristic High-Tension Magneto Solid-State Electronic Ignition Turbine Capacitor-Discharge Exciter
Energy source Self-generating; engine rotation only Aircraft bus, backed by a secondary power source Aircraft 28 V DC or 115 V AC bus
Timing Fixed mechanical advance set at E-gap Continuously varied with speed and manifold pressure Not crankshaft-timed; free-running spark rate
Duty Continuous, every compression stroke Continuous, every compression stroke Intermittent; starting and hazard conditions only
Field adjustment Internal timing and timing to engine None; timing is not manually adjustable None; energy is fixed by exciter design
Primary wear items Points, capacitor, distributor block, rotor, carbon brush Coil packs, harness, sensors, ECU as line-replaceable units Igniter plugs, exciter, high-tension leads
Characteristic hazard Open P-lead leaves the magneto hot Stored coil energy; ECU can command a spark at rest Lethal stored capacitor charge; mandatory bleed-down wait
Independent Prep Note
Independent FAA AMT Powerplant prep by ExamFinch. Not sponsored by or affiliated with the Federal Aviation Administration (FAA). Technical data compiled from FAA-H-8083-32B, FAA AC 43.13-1B, and 14 CFR Parts 43 and 65.