Study guide
2.2 Dynamic Dampers, Counterweights & Vibration Control
FAA Aviation Mechanic — Powerplant AMP
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Reciprocating Engine Theory & Construction
1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies
2 Chapter 2: Reciprocating Engine Dynamics & Valve Train
2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines
3 Chapter 3: Turbine Engine Theory & Compressors
3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems
4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards
4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)
5 Chapter 5: Engine Ignition & Starting Systems
5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems
6 Chapter 6: Propeller Fundamentals & Governors
6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems
7 Chapter 7: Propeller Maintenance & Turboprop Controls
7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control
8 Chapter 8: Engine Fuel Metering Systems
8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment
9 Chapter 9: Engine Lubrication Systems
9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting
10 Chapter 10: Induction, Supercharging & Engine Cooling
10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression
11 Chapter 11: Engine Electrical Systems
11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling
12 Chapter 12: Engine Instrument Systems
12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings
13 Chapter 13: Aircraft Engine Fuel Systems
13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC
14 Chapter 14: Engine Inspection, Records & Maintenance
14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts
15 Chapter 15: Engine Removal, Installation & Overhaul
15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures
16 Chapter 16: Engine Fire Protection & Exhaust Systems
16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers
2.2 Dynamic Dampers, Counterweights & Vibration Control
Key Takeaways Explain This Topic AI
Torsional vibration is the cyclic angular twisting forward and springing backward of the crankshaft along its rotational axis, caused by intermittent power stroke pressure impulses and reciprocating inertia.
Dynamic dampers (pendulum counterweights) are suspended on floating pins and bushings, utilizing centrifugal restoring force to automatically adjust their natural oscillating frequency to match engine RPM across all operating ranges.
Unlike static counterweights that balance rotating mass, dynamic dampers act as tuned mechanical absorbers specifically designed to suppress critical torsional harmonic orders and prevent crankshaft fatigue fracture.
Technicians must never grease, wedge, clamp, or paint dynamic damper counterweights or pins; damper weights must move freely by hand when clean and dry during maintenance inspections per FAA-H-8083-32B.
Dynafocal engine mounts feature elastomeric isolators oriented directly toward the center of gravity (CG) of the engine-propeller assembly, isolating torsional, pitching, and yawing vibrational moments from the aircraft structure.
Last updated: September 2026
2.2 Dynamic Dampers, Counterweights & Vibration Control
Quick Answer: Torsional vibration is the cyclic twisting and untwisting of an aircraft crankshaft caused by repetitive, pulsating cylinder firing impulses. If these impulses match the crankshaft's natural torsional frequency, resonant vibration can quickly fracture the shaft. To neutralize these forces across varying engine speeds, aircraft engines utilize pendulum dynamic dampers (dynamic counterweights). Because their restoring force is centrifugal force—which varies directly with the square of engine rotational speed—the pendulum's oscillating frequency remains automatically synchronized to specific engine harmonic orders at all RPMs. Technicians must ensure damper pins and bushings are clean, dry, and move freely by hand without grease or binding. Engine-to-airframe vibration is further controlled by Dynafocal mounts , which orient elastomeric isolators toward the engine-propeller center of gravity.
Torsional Vibration in Aircraft Reciprocating Engines
In an electric motor or gas turbine engine, torque is delivered to the output shaft smoothly and continuously. In an aircraft reciprocating internal combustion engine, however, power is delivered in a succession of discrete, violent power stroke hammer blows separated by compression, exhaust, and intake strokes.
The Dynamics of Angular Deflection
Every time a cylinder fires, peak gas pressure exerts a massive downward thrust on the piston and connecting rod, driving the crankpin forward. The inertia of the heavy propeller hub and blades at the front of the engine resists this sudden acceleration:
Twisting Forward: As the crankpin is forced ahead by the power stroke, the forward journals and propeller shaft lag behind due to propeller inertia. Consequently, the crankshaft twists elastically along its longitudinal rotational axis.
Springing Backward: As the power stroke concludes and gas pressure diminishes, the internal elastic resilience of the forged alloy steel crankshaft causes it to rebound and spring backward past its neutral position.
Cyclic Oscillation: This rapid alternating cycle—twisting forward during power pulses and rebounding backward between pulses—constitutes torsional vibration . Torsional Vibration Deflection Along Crankshaft Axis
- Propeller Hub Crankpin Throw Accessory End
- [High Inertia] [Power Impulse] [Free Flange]
- | | |
- ( O )=========+====================( O )===========================+ |
- | ^ |
- Restrains Forward Motion Forces Crankpin Ahead Rebounds Backward
- [Elastic Twisting Angle] [Piston Thrust Pulse] [Spring Reversal]
It is critical to note that torsional vibration is not a physical back-and-forth bodily shaking of the engine on its mounts (which is linear or lateral reciprocating vibration); rather, it is a rapid internal winding and unwinding of the crankshaft structure itself.
Harmonics, Resonance, and Critical Engine Speeds
Every mechanical structure has one or more natural frequencies of vibration determined by its mass, geometry, and material stiffness. A steel crankshaft behaves like an intricate torsional spring-mass system with defined natural torsional resonant frequencies.
Engine Firing Harmonics and Order Calculation
The frequency of the recurring torque impulses applied to the crankshaft depends directly on engine cylinder count, operating stroke, and engine RPM. In a standard four-stroke engine, each cylinder fires once every two crankshaft revolutions: Power Impulses per Crankshaft Revolution = Number of Cylinders 2 \text{Power Impulses per Crankshaft Revolution} = \frac{\text{Number of Cylinders}}{2} Power Impulses per Crankshaft Revolution = 2 Number of Cylinders
In a four-cylinder engine , there are 4 / 2 = 2 4 / 2 = 2 4/2 = 2 power impulses per revolution (2nd harmonic order).
In a six-cylinder engine , there are 6 / 2 = 3 6 / 2 = 3 6/2 = 3 power impulses per revolution (3rd harmonic order).
In an eight-cylinder engine , there are 8 / 2 = 4 8 / 2 = 4 8/2 = 4 power impulses per revolution (4th harmonic order).
In a nine-cylinder radial engine , there are 9 / 2 = 4.5 9 / 2 = 4.5 9/2 = 4.5 power impulses per revolution (4.5 harmonic order).
In addition to the primary firing frequency, complex secondary and higher-order harmonic vibrations are generated by reciprocating piston inertia forces and valve train operations.
Resonance and Critical Speeds
When the engine operates at an RPM where the frequency of one of these torsional harmonic orders coincides exactly with the natural torsional frequency of the crankshaft, a state of resonance is established: Firing Harmonic Frequency = Crankshaft Natural Torsional Frequency \text{Firing Harmonic Frequency} = \text{Crankshaft Natural Torsional Frequency} Firing Harmonic Frequency = Crankshaft Natural Torsional Frequency
During resonance, each successive firing impulse reinforces the preceding vibration wave, causing the angular twist amplitude to multiply rapidly. This condition occurs at specific rotational velocities known as critical speeds :
If an engine is permitted to operate continuously at a critical speed, the intense cyclical shear stresses exceed the fatigue endurance limit of the forged steel shaft.
Failure Modes: Torsional resonance produces rapid fatigue cracking across crankshaft crankpin journals, fractures through crankshaft webs at the journal fillets, shears propeller mounting bolts, strips supercharger and accessory drive gears, and causes premature propeller blade failure.
Tachometer Markings: When an aircraft engine-propeller combination has an unavoidable critical speed within its operating range, the FAA Type Certificate requires a yellow or red arc (restricted range) on the cockpit tachometer (e.g., "Avoid continuous operation between 2,100 and 2,350 RPM"). Technicians and pilots must ensure the engine transitions quickly through this range without continuous operation.
Static Balance vs. Dynamic Balance
Crankshaft balance is divided into two distinct engineering classifications: static balance and dynamic balance.
Feature Static Balance Dynamic Balance
Definition Balance of weight around the rotational axis while at rest Balance of forces and couples generated during high-speed rotation
Physical Objective Ensures the center of gravity lies exactly on the rotational centerline Eliminates rocking couples and bending moments along the shaft length
Mechanism Rigid, fixed counterweights forged or bolted opposite crankpins Dynamic counterweights, pendulum dampers, precision weight matching
Correction Tool Knife-edge balance ways or arbor rollers Electronic balancing equipment, stroboscopic dynamic analyzers
Static Balance
A crankshaft possesses static balance when its center of gravity lies precisely along its rotational axis. If placed on perfectly level knife-edge balancing ways, a statically balanced crankshaft will remain stationary in any angular position without rolling to a heavy side. Fixed counterweights forged opposite the crankpins offset the static rotating mass of the crank cheeks, crankpins, and the rotating portion of the connecting rod big-ends.
Dynamic Balance
A crankshaft may be statically balanced yet dynamically unbalanced. When the shaft rotates at high speed, centrifugal forces acting on masses located in different planes along the crankshaft produce rocking couples (moments that attempt to twist the engine end-for-end or wobble the shaft in its bearings). Dynamic balancing ensures that all centrifugal forces and moments cancel out during operation.
However, neither static counterweights nor conventional dynamic balance can eliminate torsional vibration , because torsional vibration is an elastic angular acceleration and deceleration, not a static mass imbalance. Torsional vibration requires specialized dynamic damping.
Centrifugal Pendulum Dynamic Dampers
To absorb torsional vibrations across varying engine speeds, aircraft engines utilize pendulum dynamic dampers , commonly referred to as dynamic counterweights .
Why Fixed Counterweights Fail Against Torsional Vibration
A fixed mass counterweight rigidly bolted to the crankshaft cheek cannot eliminate torsional vibration because a fixed mass has a single, fixed natural frequency. While it might neutralize torsional vibration at one specific engine RPM, it would be completely ineffective—and could even worsen vibration—at all other RPMs.
The Physics of the Centrifugal Pendulum
A simple pendulum suspended in a gravitational field has a natural frequency determined solely by gravity ( g g g ) and its pendulum suspension length ( L L L ): f = 1 2 π g L f = \frac{1}{2\pi} \sqrt{\frac{g}{L}} f = 2 π 1 L g
In a rotating crankshaft, however, the dynamic counterweight is subjected to an intense centrifugal acceleration field ( r ω 2 r\omega^2 r ω 2 , where r r r is the radius from the crankshaft center of rotation and ω \omega ω is rotational velocity in radians per second). This centrifugal force completely replaces gravity as the restoring force acting on the suspended counterweight.
The natural oscillating frequency of this centrifugal pendulum damper ( f p f_p f p ) is expressed by the formula: f p = ω 2 π R L f_p = \frac{\omega}{2\pi} \sqrt{\frac{R}{L}} f p = 2 π ω L R
where:
- ω \omega ω = crankshaft angular rotational speed
- R R R = distance from the crankshaft center of rotation to the center of the damper suspension pivot
- L L L = effective pendulum length Geometry of the Centrifugal Pendulum Dynamic Damper
- Crankshaft Center of Rotation
- ( + )
- |
- | <--- Distance R
- |
- +---------------+---------------+
- | Crankshaft Cheek Extension |
- | ( O ) |
- +--------------|----------------+
- | <--- Floating Pin in Oversized Holes
- | Effective Pendulum Length L = (D_hole - D_pin)
- +--------------|----------------+
- | ( O ) Dynamic Counterweight |
- | \ |
- | =====> Swings Out-of-Phase
- +-------------------------------+
- Automatic RPM Tuning
Because the restoring centrifugal force increases directly with the square of crankshaft rotational speed ( ω 2 \omega^2 ω 2 ), the natural frequency of the dynamic pendulum ( f p f_p f p ) is directly proportional to engine speed ( ω \omega ω ) : f p ω = 1 2 π R L = Constant Ratio \frac{f_p}{\omega} = \frac{1}{2\pi} \sqrt{\frac{R}{L}} = \text{Constant Ratio} ω f p = 2 π 1 L R = Constant Ratio
This mathematical relationship is one of the most profound engineering achievements in aviation powerplant design:
A dynamic damper dimensioned for a specific harmonic order (such as the 6th harmonic order) remains tuned to that exact harmonic order at every engine RPM from idle to full takeoff power!
When the crankshaft twists forward during a cylinder firing impulse, the counterweight swings backward relative to the cheek. When the crankshaft rebounds, the counterweight swings forward.
By oscillating 180° out of phase with the torsional deflection waves, the dynamic damper absorbs the destructive vibrational energy and feeds it back smoothly into the shaft, neutralizing the torsional stress peak.
Mechanical Construction: Pins, Bushings, and Pendulum Length
A dynamic damper counterweight is not rigidly attached to the crankshaft cheek. Instead, it is suspended on the cheek using precision-ground, floating, hardened alloy steel pins and bushings .
Slotted Mounting: The counterweight contains precision-machined slots that straddle the crankshaft counterweight cheek.
Oversized Holes: The holes bored through the crankshaft cheek and the matching holes bored through the dynamic counterweight are lined with hardened steel bushings. These holes are machined with a diameter significantly larger than the diameter of the hardened steel connecting pin.
Determining Effective Pendulum Length ( L L L ): The effective pendulum length L L L is determined strictly by the dimensional difference between the diameter of the bushing holes ( D hole D_{\text{hole}} D hole ) and the outside diameter of the floating pin ( D pin D_{\text{pin}} D pin ): L = D hole − D pin L = D_{\text{hole}} - D_{\text{pin}} L = D hole − D pin
By manufacturing these pins and bushings to tolerances measured in ten-thousandths of an inch, powerplant engineers precisely tune the damper to target specific destructive torsional harmonic orders.
Inspection, Servicing, and Overhaul Standards (FAA-H-8083-32B & 14 CFR Part 43)
Due to the extreme alternating forces acting on dynamic dampers, their mounting hardware is subject to meticulous inspection standards under 14 CFR Part 43 and engine overhaul manuals:
Critical Wear Limits and Defects
Brinelling and Galling: Technicians must visually inspect the dynamic damper pins and cheek bushings for brinelling (indentations caused by heavy impact loads), fretting corrosion, pitting, and metal galling. Any perceptible flat spot or step on a pin requires immediate rejection and replacement.
Bushing Walk: Inspect for axial migration ("bushing walk") where the press-fit bushing has shifted laterally inside the counterweight or cheek bore, which could bind the counterweight.
Pin and Bushing Clearance: Measure pin outside diameter and bushing inside diameter with precision micrometers and bore gauges to verify that clearances remain within the manufacturer's Table of Limits.
The Mandatory Free-Movement Check
During engine assembly or 100-hour / annual inspections where access is available:
When clean and dry, dynamic counterweights must move freely by hand through their entire arc of travel on their pins.
Any binding, roughness, sluggishness, or mechanical interference is cause for disassembly and component rejection.
Warning
Strict Prohibition Against Lubrication, Wedging, or Alterations: Technicians must never apply heavy chassis grease, anti-seize compound, paint, or shims to dynamic damper pins and bushings. Contamination or grease will pack the clearances, causing the counterweight to drag or stick. If a dynamic counterweight binds, its pendulum action is completely destroyed, turning it into a dead fixed mass. The engine crankshaft will instantly be subjected to unattenuated torsional resonance, leading to rapid crankshaft fatigue fracture and catastrophic in-flight engine failure!
Comparison of Aircraft Engine Vibration Modes
Vibration Mode Physical Characteristic Primary Excitation Source Frequency / Order Dampening & Control Mechanism
Torsional Vibration Elastic angular twisting and unwinding along crankshaft axis Intermittent cylinder firing impulses and power pulses Integer & half-integer engine orders (e.g., 3rd, 4.5, 6th) Centrifugal pendulum dynamic dampers; tuned torsional quill shafts
Linear Reciprocating Vibration Back-and-forth bodily shaking along cylinder axis Reciprocating mass of pistons, wrist pins, and rods accelerating/decelerating Primary (1× RPM) and secondary (2× RPM) Static counterweights on crank cheeks; opposing cylinder layout
Lateral / Coupled Moments Rocking couples attempting to pitch or yaw the engine Off-axis mass distribution and staggered cylinder banks 1× and 2× engine RPM Dynamic balancing of crankshaft; Dynafocal engine mounts
Propeller Aerodynamic Unbalance 1× RPM lateral and thrust vibration Unequal blade pitch, blade tracking errors, or mass imbalance Exactly 1× propeller RPM Blade tracking checks; dynamic electronic propeller balancing (target <0.05 IPS)
Aircraft Engine Vibration Isolation: Dynafocal Mounts
While dynamic dampers mitigate internal crankshaft torsional stresses, residual vibrations must still be prevented from transmitting into the aircraft firewall, cabin, and avionics bays.
Conventional Conical Mounts vs. Dynafocal Mounts
Conventional Conical Mounts: Early aircraft utilized simple straight rubber shock bushings (conical mounts) where the mounting bolts were parallel to the crankshaft thrust line. These mounts absorbed longitudinal thrust and axial vibration but provided poor isolation against torsional engine roll, pitching, and yawing moments, causing heavy vibration in the cockpit.
Dynafocal Mount Assemblies: Modern horizontally opposed and radial engines utilize Dynafocal engine mounting systems . In a Dynafocal mount, the elastomeric shock mount assemblies are set at compound angles such that the directional centerlines of all mounting bolts converge and focus directly at the center of gravity (CG) of the combined engine and propeller assembly. Dynafocal Mount Geometric Convergence
- Engine Mount Ring / Airframe Structure
- +------------------------------------------+
- | [Mount 1] |
- | \ |
- | \ |
- | \ |
- | [Mount 2] --------> ( CG ) <-------- [Mount 3]
- | / |
- | / |
- | / |
- | [Mount 4] |
- +------------------------------------------+
- Convergence at Engine-Propeller CG
- Advantages of Center-of-Gravity Focus
By focusing the mount elasticity through the center of gravity:
Decoupled Moments: Rotational roll vibrations around the crankshaft axis are decoupled from pitching and yawing moments.
Free Torsional Rotation: The engine is permitted a tiny, cushioned rotational freedom around its true principal inertia axis (roll axis) without transferring torsional kick into the airframe.
Component Longevity: Minimizes structural fatigue cracking of engine baffles, exhaust manifolds, airframe cowl attach points, and delicate gyro flight instruments.
Dynamic Propeller Balancing
Under modern maintenance procedures, technicians use computerized dynamic balancers to achieve final vibration suppression:
An optical tachometer sensor tracks propeller rotational index (reflective tape).
An accelerometer mounted to the engine crankcase nose measures vibration amplitude in Inches Per Second (IPS) .
The dynamic balancer calculates the exact mass and angular clock location for balance washers installed on the propeller spinner bulkhead.
FAA standards target vibration levels below 0.05 IPS , providing smooth operation and protecting against crankshaft nose bearing fretting.
Independent Prep Note
Independent FAA AMT Powerplant prep by ExamFinch. Not sponsored by or affiliated with the Federal Aviation Administration (FAA). Technical data compiled from FAA-H-8083-32B, FAA AC 43.13-1B, and 14 CFR Parts 43 and 65.