Study guide
1.3 Compression Ratio, Manifold Pressure & Power Calculations
FAA Aviation Mechanic — Powerplant AMP
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Reciprocating Engine Theory & Construction
1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies
2 Chapter 2: Reciprocating Engine Dynamics & Valve Train
2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines
3 Chapter 3: Turbine Engine Theory & Compressors
3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems
4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards
4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)
5 Chapter 5: Engine Ignition & Starting Systems
5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems
6 Chapter 6: Propeller Fundamentals & Governors
6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems
7 Chapter 7: Propeller Maintenance & Turboprop Controls
7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control
8 Chapter 8: Engine Fuel Metering Systems
8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment
9 Chapter 9: Engine Lubrication Systems
9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting
10 Chapter 10: Induction, Supercharging & Engine Cooling
10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression
11 Chapter 11: Engine Electrical Systems
11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling
12 Chapter 12: Engine Instrument Systems
12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings
13 Chapter 13: Aircraft Engine Fuel Systems
13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC
14 Chapter 14: Engine Inspection, Records & Maintenance
14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts
15 Chapter 15: Engine Removal, Installation & Overhaul
15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures
16 Chapter 16: Engine Fire Protection & Exhaust Systems
16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers
1.3 Compression Ratio, Manifold Pressure & Power Calculations
Key Takeaways Explain This Topic AI
Compression ratio (CR) is the ratio of total cylinder volume at BDC to clearance volume at TDC, directly governing thermal efficiency and fuel octane requirements.
Indicated horsepower (IHP) represents total thermodynamic power generated inside the combustion chambers, calculated via the PLANK formula using Indicated Mean Effective Pressure (IMEP).
Brake horsepower (BHP) is the actual usable mechanical power delivered at the propeller shaft, determined by dynamometer torque and rotational speed; BHP equals IHP minus friction horsepower (FHP).
Manifold Absolute Pressure (MAP) gauges indicate absolute induction system pressure in inches of mercury (inHg); an inoperative engine at sea level indicates ambient atmospheric pressure (~29.92 inHg).
Mechanical efficiency (BHP / IHP) of modern aircraft reciprocating engines typically ranges between 85% and 90%, with the remainder consumed by mechanical friction, pumping losses, and accessory drives.
Last updated: September 2026
1.3 Compression Ratio, Manifold Pressure & Power Calculations
Quick Answer: Engine power output is governed by cylinder displacement geometry, compression ratio, induction pressure, and thermodynamic efficiency. The PLANK formula ( P L A N K / 33 , 000 PLANK / 33,000 P L A N K /33 , 000 ) calculates Indicated Horsepower (IHP) , the total chemical-thermal power generated in the cylinders. Brake Horsepower (BHP) is the actual usable shaft power delivered to the propeller after subtracting Friction Horsepower (FHP) . Manifold Absolute Pressure (MAP) directly measures induction charge density. Independent FAA AMT Powerplant prep by ExamFinch.
Compression Ratio (CR) Geometry and Mechanics
Compression ratio is a volumetric ratio that compares the maximum internal volume of a cylinder when the piston is at Bottom Dead Center (BDC) to the minimum volume remaining when the piston reaches Top Dead Center (TDC): Compression Ratio (CR) = V total V c = V d + V c V c \text{Compression Ratio (CR)} = \frac{V_{\text{total}}}{V_c} = \frac{V_d + V_c}{V_c} Compression Ratio (CR) = V c V total = V c V d + V c
Where:
V d V_d V d = Piston Displacement: The physical volume swept out by the piston crown as it travels the length of its stroke from TDC to BDC.
V c V_c V c = Clearance Volume: The volume remaining inside the combustion chamber above the piston crown when the piston is at the very top of its stroke (TDC). +------------------------+ <-- Cylinder Head
- | Clearance Volume (Vc) | <-- Piston at TDC
- +========================+
- | | ^
- | | |
- | | | Stroke (L)
- | Piston Displacement | | Piston sweeps Vd
- | (Vd) | |
- | | v
- +========================+ <-- Piston at BDC
- | Crankcase |
- Piston Displacement Formula
The piston displacement of a single cylinder is calculated from its bore (internal cylinder diameter, B B B ) and its stroke (piston travel distance, S S S or L L L ): V d = π × B 2 × S 4 = π × r 2 × S V_d = \frac{\pi \times B^2 \times S}{4} = \pi \times r^2 \times S V d = 4 π × B 2 × S = π × r 2 × S
To find the total engine displacement , multiply single-cylinder displacement ( V d V_d V d ) by the total number of cylinders ( K K K ): Total Engine Displacement = V d × K \text{Total Engine Displacement} = V_d \times K Total Engine Displacement = V d × K
Worked Example: An aircraft engine has a 5.125-inch cylinder bore, a 4.375-inch stroke, and a clearance volume ( V c V_c V c ) of 11.28 cubic inches. Find its compression ratio:
V d = π × ( 5.125 ) 2 × 4.375 4 = 0.7854 × 26.2656 × 4.375 ≈ 90.25 cu in V_d = \frac{\pi \times (5.125)^2 \times 4.375}{4} = 0.7854 \times 26.2656 \times 4.375 \approx 90.25\text{ cu in} V d = 4 π × ( 5.125 ) 2 × 4.375 = 0.7854 × 26.2656 × 4.375 ≈ 90.25 cu in .
V total = V d + V c = 90.25 + 11.28 = 101.53 cu in V_{\text{total}} = V_d + V_c = 90.25 + 11.28 = 101.53\text{ cu in} V total = V d + V c = 90.25 + 11.28 = 101.53 cu in .
CR = 101.53 11.28 ≈ 9.0 : 1 \text{CR} = \frac{101.53}{11.28} \approx 9.0:1 CR = 11.28 101.53 ≈ 9.0 : 1 .
Thermodynamic Significance of Compression Ratio
Increasing the compression ratio directly increases the engine's thermal efficiency and reduces Specific Fuel Consumption (SFC) . Compressing the fuel-air charge more tightly forces fuel molecules closer to oxygen, increases mixture temperature prior to ignition, accelerates combustion velocity, and allows expanding gases to extract more mechanical work across a longer effective expansion ratio.
However, compression ratio is physically limited by the anti-knock (detonation) rating of aviation gasoline. Exceeding design compression ratios causes the compressed mixture to reach its auto-ignition temperature, producing catastrophic detonation. Modern high-compression aircraft engines (e.g., 8.5:1 or 8.7:1) mandate 100LL avgas, whereas low-compression engines (e.g., 7.0:1) can safely operate on lower-octane fuels or approved unleaded aviation gasolines.
Manifold Absolute Pressure (MAP) Dynamics
The Manifold Absolute Pressure (MAP) gauge is an absolute pressure-sensing flight instrument connected to the engine induction intake runner downstream of the throttle plate. It measures the absolute pressure of the fuel-air charge delivered to the cylinders in inches of mercury (inHg) .
Operating Condition Engine State Typical MAP Reading Physical Explanation
Engine Stopped (Static) Inoperative on ground Ambient barometric pressure (~29.92 inHg at sea level) No induction flow; manifold interior equals atmospheric pressure
Engine Idle (Closed Throttle) Running at 600–800 RPM 10 to 15 inHg absolute Closed throttle plate restricts airflow; descending pistons evacuate manifold
Full Throttle (Naturally Aspirated) Rated takeoff power at sea level 28 to 28.5 inHg Induction air filter and throttle body friction cause 1.0–1.5 inHg pressure drop below ambient
Altitude Climb (Naturally Aspirated) Wide Open Throttle (WOT) Drops ~1.0 inHg per 1,000 ft Ambient air density decreases with altitude; power decreases linearly
Turbocharged / Supercharged Rated takeoff power 35 to 45+ inHg (Boost) Compressor pressurizes intake charge above ambient atmospheric pressure
The Static MAP Gauge Principle
A fundamental question on the FAA Powerplant examination tests candidate understanding of a stopped engine: When an aircraft engine is not running, what does the manifold pressure gauge indicate? Because the manifold gauge contains an evacuated aneroid bellows that references absolute zero pressure, it registers the prevailing atmospheric barometric pressure of the surrounding airfield. At sea level on a standard day (ISA standard), it indicates 29.92 inHg . At an airport located at 5,000 feet elevation, it indicates approximately 24.9 inHg .
Power Hierarchy: Indicated, Brake, and Friction Horsepower
Power is defined as the rate of doing work. In English engineering units, one horsepower (hp) equals 33,000 foot-pounds of work per minute (or 550 foot-pounds per second), a standard established by James Watt. [ Total Chemical Energy in Fuel ]
- |
- v
- [ Indicated Horsepower (IHP) ] <--- Total power generated in cylinders
- | |
- | (Losses) v
- | [ Friction Horsepower (FHP) ] <--- Internal friction & accessories
- v
- [ Brake Horsepower (BHP) ] <--- Usable shaft power delivered to propeller
- 1. Indicated Horsepower (IHP)
Indicated Horsepower is the total theoretical power developed by the expanding combustion gases inside the engine cylinders, completely ignoring all internal mechanical friction and pumping losses. It is calculated directly from cylinder pressure data using the PLANK formula .
2. Brake Horsepower (BHP)
Brake Horsepower is the actual, net usable mechanical power delivered by the engine crankshaft to the propeller shaft. It is termed "brake" horsepower because it was historically measured by applying a mechanical friction brake (prony brake) or dynamometer to the output shaft: BHP = 2 π × Torque (ft-lb) × RPM 33 , 000 = Torque × RPM 5 , 252 \text{BHP} = \frac{2\pi \times \text{Torque (ft-lb)} \times \text{RPM}}{33,000} = \frac{\text{Torque} \times \text{RPM}}{5,252} BHP = 33 , 000 2 π × Torque (ft-lb) × RPM = 5 , 252 Torque × RPM
3. Friction Horsepower (FHP)
Friction Horsepower is the power consumed by the engine in turning itself over. It represents the difference between theoretical power developed and net power delivered: FHP = IHP − BHP \text{FHP} = \text{IHP} - \text{BHP} FHP = IHP − BHP
Friction horsepower losses stem from three primary sources:
Mechanical Sliding Friction: Piston rings sliding against cylinder walls (accounts for over 50% of total FHP), crankshaft main and rod journals rotating in sleeve bearings, and rocker arm bushings.
Pumping Losses: Work consumed during the intake and exhaust strokes in drawing in fresh charge and pushing spent exhaust gases through restricted ports and manifolds.
Accessory Drive Consumption: Power consumed driving engine-mounted accessories, including dual magnetos, the engine oil pump, scavenge pumps, fuel injection pumps, alternator, and internal supercharger impellers.
4. Mechanical Efficiency ( η m \eta_m η m )
Mechanical efficiency is the ratio of usable shaft power delivered to total power developed: η m = BHP IHP × 100 % \eta_m = \frac{\text{BHP}}{\text{IHP}} \times 100\% η m = IHP BHP × 100%
In well-engineered, modern aircraft reciprocating engines operating at rated power, mechanical efficiency typically ranges between 85% and 90% .
The PLANK Formula for Indicated Horsepower
The most famous equation on the FAA Aviation Maintenance Technician examination is the PLANK formula , used to compute Indicated Horsepower: IHP = P ⋅ L ⋅ A ⋅ N ⋅ K 33 , 000 \text{IHP} = \frac{P \cdot L \cdot A \cdot N \cdot K}{33,000} IHP = 33 , 000 P ⋅ L ⋅ A ⋅ N ⋅ K
Every parameter in this equation has a rigorous engineering definition and specific unit requirements:
Variable Engineering Definition Required Units & Formula
P P P Indicated Mean Effective Pressure (IMEP) Pounds per square inch (psi). The theoretical average pressure acting against the piston crown throughout the power stroke.
L L L Length of Stroke Must be in FEET. Convert from inches: L = Stroke in inches / 12 L = \text{Stroke in inches} / 12 L = Stroke in inches /12 .
A A A Area of Piston Crown Square inches ( sq in \text{sq in} sq in ). A = π × Bore 2 4 A = \frac{\pi \times \text{Bore}^2}{4} A = 4 π × Bore 2 or π × r 2 \pi \times r^2 π × r 2 .
N N N Power Strokes per Minute per Cylinder For a four-stroke engine: N = Engine RPM / 2 N = \text{Engine RPM} / 2 N = Engine RPM /2 . (Because each cylinder fires once every 2 crankshaft revolutions).
K K K Number of Cylinders Total cylinder count of the engine.
33 , 000 33,000 33 , 000 Horsepower Constant Foot-pounds of work per minute equivalent to 1 horsepower.
CRITICAL EXAM WARNING ( N N N Trap): On the FAA exam, candidate failure on PLANK questions almost always stems from using full engine RPM for N N N . In a four-stroke engine, a cylinder produces a power stroke only once every two revolutions. Therefore, N N N must always equal RPM / 2 \text{RPM} / 2 RPM /2 .
Comprehensive PLANK Step-by-Step Calculation
Problem: Calculate the Indicated Horsepower of a six-cylinder ( K = 6 K = 6 K = 6 ) four-stroke aircraft engine operating at 2,400 RPM with an Indicated Mean Effective Pressure ( P P P ) of 140 psi, a cylinder bore of 5.0 inches, and a stroke of 4.5 inches.
Determine Stroke in Feet ( L L L ): L = 4.5 in 12 = 0.375 ft L = \frac{4.5\text{ in}}{12} = 0.375\text{ ft} L = 12 4.5 in = 0.375 ft
Determine Piston Area ( A A A ): A = π × ( 5.0 ) 2 4 = 0.7854 × 25.0 = 19.635 sq in A = \frac{\pi \times (5.0)^2}{4} = 0.7854 \times 25.0 = 19.635\text{ sq in} A = 4 π × ( 5.0 ) 2 = 0.7854 × 25.0 = 19.635 sq in
Determine Power Strokes per Minute per Cylinder ( N N N ): N = 2 , 400 RPM 2 = 1 , 200 power strokes/min N = \frac{2,400\text{ RPM}}{2} = 1,200\text{ power strokes/min} N = 2 2 , 400 RPM = 1 , 200 power strokes/min
Apply the PLANK Formula: IHP = 140 × 0.375 × 19.635 × 1 , 200 × 6 33 , 000 \text{IHP} = \frac{140 \times 0.375 \times 19.635 \times 1,200 \times 6}{33,000} IHP = 33 , 000 140 × 0.375 × 19.635 × 1 , 200 × 6 Numerator = 140 × 0.375 × 19.635 × 1 , 200 × 6 = 7 , 422 , 030 ft-lb/min \text{Numerator} = 140 \times 0.375 \times 19.635 \times 1,200 \times 6 = 7,422,030\text{ ft-lb/min} Numerator = 140 × 0.375 × 19.635 × 1 , 200 × 6 = 7 , 422 , 030 ft-lb/min IHP = 7 , 422 , 030 33 , 000 ≈ 224.9 IHP \text{IHP} = \frac{7,422,030}{33,000} \approx 224.9\text{ IHP} IHP = 33 , 000 7 , 422 , 030 ≈ 224.9 IHP
If this engine exhibits a mechanical efficiency of 88%, its usable Brake Horsepower is: BHP = IHP × η m = 224.9 × 0.88 = 197.9 BHP \text{BHP} = \text{IHP} \times \eta_m = 224.9 \times 0.88 = 197.9\text{ BHP} BHP = IHP × η m = 224.9 × 0.88 = 197.9 BHP
Friction horsepower consumed internally is: FHP = IHP − BHP = 224.9 − 197.9 = 27.0 FHP \text{FHP} = \text{IHP} - \text{BHP} = 224.9 - 197.9 = 27.0\text{ FHP} FHP = IHP − BHP = 224.9 − 197.9 = 27.0 FHP
Efficiencies: Thermal, Volumetric, and BSFC
Brake Specific Fuel Consumption (BSFC): The mass of fuel consumed per hour per unit of brake horsepower produced: BSFC = Fuel Flow (lb/hr) / BHP \text{BSFC} = \text{Fuel Flow (lb/hr)} / \text{BHP} BSFC = Fuel Flow (lb/hr) / BHP . Typical aviation reciprocating values range between 0.42 and 0.48 lb/(BHP·hr) at cruise.
Thermal Efficiency ( η t h \eta_{th} η t h ): The percentage of total chemical energy in the consumed fuel converted into mechanical shaft work. Aircraft reciprocating engines achieve 30% to 34% thermal efficiency; the remaining 66% to 70% is rejected as waste heat to exhaust gas (~45%), cylinder cooling fins (~15%–20%), and engine lubricating oil (~5%–10%).
Volumetric Efficiency ( η v \eta_v η v ): The ratio of the mass of fuel-air charge inducted into the cylinder to the theoretical mass that would completely fill the cylinder displacement volume under static ambient conditions. Sharp induction bends, high carburetor heat, and restrictive air filters reduce volumetric efficiency.