Study guide

1.1 Four-Stroke Cycle & Otto Cycle Fundamentals

FAA Aviation Mechanic — Powerplant AMP

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Reciprocating Engine Theory & Construction

1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies

2 Chapter 2: Reciprocating Engine Dynamics & Valve Train

2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines

3 Chapter 3: Turbine Engine Theory & Compressors

3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems

4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards

4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)

5 Chapter 5: Engine Ignition & Starting Systems

5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems

6 Chapter 6: Propeller Fundamentals & Governors

6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems

7 Chapter 7: Propeller Maintenance & Turboprop Controls

7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control

8 Chapter 8: Engine Fuel Metering Systems

8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment

9 Chapter 9: Engine Lubrication Systems

9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting

10 Chapter 10: Induction, Supercharging & Engine Cooling

10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression

11 Chapter 11: Engine Electrical Systems

11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling

12 Chapter 12: Engine Instrument Systems

12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings

13 Chapter 13: Aircraft Engine Fuel Systems

13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC

14 Chapter 14: Engine Inspection, Records & Maintenance

14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts

15 Chapter 15: Engine Removal, Installation & Overhaul

15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures

16 Chapter 16: Engine Fire Protection & Exhaust Systems

16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers

1.1 Four-Stroke Cycle & Otto Cycle Fundamentals

Key Takeaways Explain This Topic AI

A four-stroke aircraft reciprocating engine requires four 180° piston strokes—totaling 720° of crankshaft rotation—to complete five thermodynamic events: intake, compression, ignition, power, and exhaust.

The camshaft is mechanically geared to the crankshaft and turns at exactly one-half (1:2 ratio) crankshaft rotational speed in all four-stroke aviation engines.

Ignition occurs before top dead center (typically 20° to 30° BTDC) so that normal flame front propagation develops peak cylinder combustion pressure at 12° to 15° after top dead center (ATDC).

Horizontally opposed aircraft engines deliver superior power-to-weight ratios, minimal aerodynamic frontal area, and balanced reciprocating forces, making them the dominant general aviation powerplant configuration.

Thermodynamically, the Otto cycle is defined by constant-volume heat addition during combustion, contrasting sharply with constant-pressure heat addition in turbine Brayton cycles.

Last updated: October 2026

1.1 Four-Stroke Cycle & Otto Cycle Fundamentals

Quick Answer: The four-stroke Otto cycle converts fuel chemical energy into mechanical torque through four 180° piston strokes— Intake, Compression, Power, and Exhaust —requiring two complete crankshaft revolutions (720°). Five distinct operating events take place: intake, compression, ignition, power, and exhaust. Ignition is a thermodynamic event, not a separate mechanical stroke. The camshaft is geared to rotate at exactly one-half crankshaft speed . Independent FAA AMT Powerplant prep by ExamFinch.

Thermodynamic Foundations: The Otto Cycle

All modern aircraft reciprocating engines operate on the principle of the Otto cycle , a four-stroke internal combustion cycle named after German engineer Nikolaus August Otto, who developed the first practical four-stroke engine in 1876. Under thermodynamic classification, an internal combustion engine is a machine that transforms chemical energy stored in hydrocarbon fuel into heat energy, and subsequently converts that heat energy into mechanical work.

In classical thermodynamics, the idealized Otto cycle is defined by four core state-change processes:

Isentropic Compression: The fuel-air charge is compressed adiabatically without heat transfer as the piston ascends from Bottom Dead Center (BDC) to Top Dead Center (TDC).

Constant-Volume Heat Addition: Combustion occurs almost instantaneously while the piston dwells momentarily at TDC, releasing chemical energy and causing a precipitous spike in cylinder pressure and temperature at essentially constant volume ( V c V_c V c ​ ).

Isentropic Expansion: The high-temperature, high-pressure combustion gases expand against the piston crown, driving the piston downward from TDC to BDC and producing positive mechanical shaft work.

Constant-Volume Heat Rejection: The exhaust valve opens, allowing rapid pressure blowdown and heat rejection to the atmosphere before the spent charge is mechanically expelled.

This constant-volume combustion characteristic fundamentally differentiates reciprocating engines from gas turbine engines, which operate on the Brayton cycle characterized by constant-pressure heat addition within an open flow path. Ideal Otto Cycle (P-V Diagram):

  • Pressure (P)
  • ^
  • | 3 (Peak Pressure / Spark Ignition)
  • | /|
  • | / | Constant-Volume Combustion (2 -> 3)
  • | / |
  • | 2 | Power Stroke Expansion (3 -> 4)
  • | | |
  • | | 4 (Exhaust Valve Blowdown)
  • | | /|
  • | 1 / 5 (Intake / Atmospheric Line)
  • +-------------------------------------> Volume (V)
  • TDC (Vc) BDC (Vd + Vc)
  • Strokes vs. Events: The Fundamental Distinction

A core distinction for the FAA Aviation Maintenance Technician (Powerplant) knowledge test is the precise distinction between an engine stroke and an engine event :

Piston Stroke: A stroke is purely a mechanical distance traveled by the piston within the cylinder barrel. It represents movement from Top Dead Center (TDC) —the highest point of piston travel closest to the cylinder head—to Bottom Dead Center (BDC) —the lowest point of travel farthest from the cylinder head—or vice versa. Each stroke accounts for exactly 180° of crankshaft rotation .

Engine Event: An event is a distinct thermodynamic or functional occurrence necessary to complete the combustion and power extraction process. A four-stroke aviation engine requires five events : intake, compression, ignition, power, and exhaust.

Because there are only four mechanical strokes (180° × 4 = 720° of crankshaft rotation) but five operating events , the ignition event does not have its own mechanical stroke. Instead, ignition occurs during the latter portion of the compression stroke, while the piston is still ascending toward TDC.

  • The Four Mechanical Strokes in Operational Sequence
  • 1. The Intake Stroke (0° to 180° Crankshaft Rotation)

The intake stroke begins with the piston at TDC. As the crankshaft rotates, the connecting rod pulls the piston downward toward BDC. This downward motion increases the volume of the combustion chamber, creating a low-pressure area (partial vacuum or depression) below ambient manifold pressure.

Before the piston reaches TDC on the preceding exhaust stroke, the intake valve has already begun to crack open ( valve lead ). As the piston sweeps downward, the pressure differential forces the atomized fuel-air mixture from the induction intake pipe through the open intake valve port into the cylinder. To take advantage of the incoming column momentum of the moving fuel-air charge, the intake valve remains open for a significant number of crankshaft degrees past BDC ( valve lag ).

2. The Compression Stroke (180° to 360° Crankshaft Rotation)

Shortly after passing BDC, the intake valve closes completely. With both the intake and exhaust valves firmly seated against their hardened valve seats, the cylinder is hermetically sealed. The piston moves upward from BDC to TDC, driven by the angular momentum of the rotating crankshaft and counterweights.

As the volume inside the cylinder decreases from total cylinder volume ( V d + V c V_d + V_c V d ​ + V c ​ ) down to clearance volume ( V c V_c V c ​ ), the trapped fuel-air charge is compressed. In accordance with the ideal gas laws ( P 1 V 1 / T 1 = P 2 V 2 / T 2 P_1 V_1 / T_1 = P_2 V_2 / T_2 P 1 ​ V 1 ​ / T 1 ​ = P 2 ​ V 2 ​ / T 2 ​ ), this mechanical compression dramatically elevates both the pressure and temperature of the charge. Compressing the mixture vaporizes lingering fuel droplets, brings fuel molecules into intimate contact with oxygen, and prepares the charge for rapid, complete combustion.

3. The Ignition Event & Power Stroke (360° to 540° Crankshaft Rotation)

Ignition is an event rather than an independent stroke. When the piston is nearing TDC on the compression stroke—typically 20° to 30° Before Top Dead Center (BTDC) depending on engine model specifications—both spark plugs fire simultaneously, energized by two independent aircraft magnetos.

Combustion is not an explosion or instantaneous detonation; it is a progressive, controlled deflagration. The flame front originates at the spark plug electrodes and sweeps across the spherical or pent-roof combustion chamber at speeds between 35 and 100 feet per second. Because flame propagation requires a finite fraction of a second, initiating spark 20° to 30° BTDC ensures that peak combustion pressure (often exceeding 600 to 1,000 psi) occurs at approximately 12° to 15° After Top Dead Center (ATDC) .

Reaching peak combustion pressure at 12° to 15° ATDC provides the maximum mechanical advantage on the crankshaft throw. As the connecting rod swings outward, this explosive gas pressure exerts enormous downward thrust on the piston crown, forcing the piston toward BDC and converting expanding gas thermal energy into rotational torque at the crankshaft.

4. The Exhaust Stroke (540° to 720° Crankshaft Rotation)

Well before the piston reaches BDC on the power stroke (typically 45° to 60° Before Bottom Dead Center [BBDC] ), the exhaust valve opens. This early opening allows the remaining combustion gas pressure (still around 40 to 60 psi) to blow down rapidly into the exhaust collector manifold, preventing backpressure resistance against the piston during its subsequent ascent.

As the crankshaft continues past BDC, the piston travels upward toward TDC, mechanically sweeping the remaining spent combustion gases out through the open exhaust valve port. The high velocity of the departing exhaust gas column establishes a localized scavenge depression inside the combustion chamber near TDC, which aids in drawing in the next fresh intake charge.

Kinematic Relationships: Crankshaft vs. Camshaft Speed

In any four-stroke reciprocating engine, each cylinder must fire once every two complete crankshaft revolutions (720° of crank rotation): Total Crankshaft Angular Travel per Cycle = 4 strokes × 180 ∘ = 720 ∘ \text{Total Crankshaft Angular Travel per Cycle} = 4 \text{ strokes} \times 180^\circ = 720^\circ Total Crankshaft Angular Travel per Cycle = 4 strokes × 18 0 ∘ = 72 0 ∘

Because each intake and exhaust valve must open and close exactly once during this 720° cycle, the engine's valve operating mechanism (the camshaft in opposed/in-line engines or the cam ring in radial engines) must turn at a precise speed ratio relative to the crankshaft: Camshaft Rotational Speed Crankshaft Rotational Speed = 1 2 = 0.5 \frac{\text{Camshaft Rotational Speed}}{\text{Crankshaft Rotational Speed}} = \frac{1}{2} = 0.5 Crankshaft Rotational Speed Camshaft Rotational Speed ​ = 2 1 ​ = 0.5

To achieve this 1:2 speed reduction, the camshaft drive gear mounted on the camshaft contains twice as many teeth as the crankshaft timing gear that drives it. If an aircraft engine operates at 2,400 RPM, the camshaft rotates at exactly 1,200 RPM. Each valve opens and closes 1,200 times per minute (20 times every second).

Mechanical Characteristic Crankshaft Camshaft

Primary Function Converts linear piston thrust into rotational torque Operates intake and exhaust poppet valves via cam lobes

  • Rotational Speed (RPM) 1.0× (Engine Indicated RPM) 0.5× (Half Engine RPM)
  • Gear Tooth Ratio 1:2 (Driving gear has N N N teeth) 2:1 (Driven gear has 2 N 2N 2 N teeth)
  • Degrees per Complete Cycle 720° (2 full revolutions) 360° (1 full revolution)
  • Power Pulses per Rev (4-cyl) 2 power strokes per revolution 4 power strokes per revolution
  • Aircraft Engine Cylinder Configurations

Aircraft reciprocating engines are classified by cylinder arrangement relative to the central crankshaft centerline:

1. Horizontally Opposed Engines (O-Type)

Horizontally opposed engines (such as the Lycoming O-360 or Continental IO-520/550 series) feature an even number of cylinders (typically four, six, or eight) arranged in two flat banks directly opposite one another across a central crankcase.

Advantages: Low aerodynamic frontal area minimizing nacelle drag, exceptional power-to-weight ratio, and excellent mechanical balance. Because opposing pistons move in opposite directions simultaneously, reciprocating forces naturally cancel each other out, yielding low vibration.

Application: The universal choice for modern single-engine and light twin-engine aircraft.

2. Radial Engines (R-Type)

Radial engines feature one or more circular rows of odd-numbered cylinders (5, 7, or 9 cylinders per single row; 14, 18, or 28 cylinders in multi-row configurations) arranged radially around a central crankcase.

Operating Principle: All connecting rods in a single row connect to a single master crankpin via one master rod and multiple articulated rods .

Odd-Number Requirement: An odd number of cylinders per row is mandatory in four-stroke radials to maintain a contiguous, even firing order (e.g., 1-3-5-7-9-2-4-6-8) across 720° of rotation.

Application: Historic transports (DC-3, B-17, B-29) and agricultural spray aircraft.

3. In-Line and V-Type Engines

In-Line: Cylinders arranged in a single straight row above or below (inverted) the crankshaft. Inverted in-line engines (such as the de Havilland Gipsy Major) improved pilot visibility and propeller ground clearance, but suffered from rear-cylinder cooling deficits in air-cooled variants.

V-Type: Cylinders arranged in two banks forming a V angle (typically 60° or 90°), sharing a common crankshaft. Prominent examples include the liquid-cooled Rolls-Royce Merlin and Allison V-1710 that powered WWII fighters.

Loading diagram... Four-Stroke Five-Event Otto Cycle Operational Sequence