Study guide

4.1 Combustion Section Designs: Can, Annular & Can-Annular

FAA Aviation Mechanic — Powerplant AMP

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Reciprocating Engine Theory & Construction

1.1 Four-Stroke Cycle & Otto Cycle Fundamentals 1.2 Valve Timing, Overlap & Duration 1.3 Compression Ratio, Manifold Pressure & Power Calculations 1.4 Crankshafts, Connecting Rods & Piston Assemblies

2 Chapter 2: Reciprocating Engine Dynamics & Valve Train

2.1 Detonation, Preignition & Combustion Anomalies 2.2 Dynamic Dampers, Counterweights & Vibration Control 2.3 Valve Clearance, Hydraulic Lifters & Radial Master Rods 2.4 Aviation Diesel & Compression-Ignition Engines

3 Chapter 3: Turbine Engine Theory & Compressors

3.1 Brayton Cycle, Thrust Principles & Spool Configurations 3.2 Axial vs. Centrifugal Compressors & Diffusers 3.3 Compressor Stalls, Angle of Attack & Bleed Systems

4 Chapter 4: Turbine Combustion, Turbines & Operational Hazards

4.1 Combustion Section Designs: Can, Annular & Can-Annular 4.2 Turbine Stages, Guide Vanes & Blade Creep 4.3 Turbine Operational Hazards: Hot Starts, Hung Starts & FOD 4.4 Turbofan, Turboprop & Auxiliary Power Units (APUs)

5 Chapter 5: Engine Ignition & Starting Systems

5.1 Magneto Operating Theory, E-Gap & Internal Timing 5.2 Magneto Check, P-Lead Grounding & Impulse Couplings 5.3 Aviation Spark Plugs: Heat Range, Fouling & Servicing 5.4 Turbine Ignition Systems & High-Energy Igniters 5.5 Solid-State & Electronic Ignition Systems

6 Chapter 6: Propeller Fundamentals & Governors

6.1 Propeller Aerodynamics, Blade Angle & Forces 6.2 Constant-Speed Governors & Pitch Change Mechanisms 6.3 Feathering, Unfeathering & Reversing Systems

7 Chapter 7: Propeller Maintenance & Turboprop Controls

7.1 Propeller Damage Limits, Minor Repairs & Servicing 7.2 Blade Tracking, Static & Dynamic Balancing 7.3 Turboprop Reduction Gearing & Beta Range Control

8 Chapter 8: Engine Fuel Metering Systems

8.1 Float-Type Carburetors & Internal Operating Systems 8.2 Carburetor Icing, Induction Heat & Density Changes 8.3 Pressure Injection Carburetors & Anti-Detonation Injection 8.4 Continuous-Flow Fuel Injection Systems (RSA & TCM) 8.5 Mixture Control, Leaning Procedures & Idle Adjustment

9 Chapter 9: Engine Lubrication Systems

9.1 Aviation Lubricant Properties, Functions & Viscosity Ratings 9.2 Wet-Sump vs. Dry-Sump Lubrication Architecture 9.3 Oil Pumps, Pressure Relief Valves & Scavenge Subsystems 9.4 Oil Filters, Coolers, Chip Detectors & Troubleshooting

10 Chapter 10: Induction, Supercharging & Engine Cooling

10.1 Reciprocating Induction Systems, Alternate Air & Air Filters 10.2 Superchargers, Turbochargers & Wastegate Controls 10.3 Air-Cooled Cylinder Cooling, Baffles & Cowl Flaps 10.4 Liquid Cooling Systems & Turbine Engine Cooling Flow 10.5 Augmenter Cooling Systems & Exhaust Noise Suppression

11 Chapter 11: Engine Electrical Systems

11.1 Starters, Alternators & DC Generators 11.2 Voltage Regulators, Current Limiters & Reverse-Current Relays 11.3 Engine Wiring Harnesses, Routing, Splicing & Clamping 11.4 Electrical Bonding, Grounding & Shielding Practices 11.5 AC Generation: Brushless Alternators, CSDs, IDGs & Paralleling

12 Chapter 12: Engine Instrument Systems

12.1 Pressure Instruments: Manifold, Oil & Fuel Pressure 12.2 Temperature Instruments: CHT, EGT & Thermocouple Principles 12.3 Tachometers, Spool Speed Sensors (N1/N2) & Synchroscopes 12.4 Turbine Performance Monitoring: EPR & Fuel Flow Indicating 12.5 Integrated Engine Indicating: EICAS, ECAM, Annunciators & Range Markings

13 Chapter 13: Aircraft Engine Fuel Systems

13.1 Fuel System Plumbing: Tanks, Selector Valves, Boost Pumps & Strainers 13.2 Vapor Lock, Fuel Contamination & Fuel Heaters 13.3 Turbine Engine Fuel Control Units: Hydromechanical & FADEC

14 Chapter 14: Engine Inspection, Records & Maintenance

14.1 100-Hour, Annual & Progressive Engine Inspections 14.2 Cylinder Compression Testing: Direct vs. Differential 14.3 Borescope Inspection Techniques & Defect Assessment 14.4 Airworthiness Directives (ADs), Service Bulletins & Logbook Entries 14.5 Special Inspections & Life-Limited Parts

15 Chapter 15: Engine Removal, Installation & Overhaul

15.1 Engine Removal Safing, Rigging, Hoisting & Disconnects 15.2 Overhaul Stages, Cleaning, NDT & Dimensional Inspection Limits 15.3 Engine Installation, Vibration Isolators, Run-Up & Break-In 15.4 Engine Preservation, Storage & Depreservation 15.5 Turbine Engine Trimming & Post-Installation Procedures

16 Chapter 16: Engine Fire Protection & Exhaust Systems

16.1 Thermal Switches, Thermocouples & Continuous-Loop Fire Detectors 16.2 Engine Fire Extinguishing Agents, Containers & Discharge Indicators 16.3 Reciprocating Exhaust Systems, Cabin Heat Muffs & Carbon Monoxide Risks 16.4 Turbine Exhaust Nozzles, Jet Pipes & Thrust Reversers

4.1 Combustion Section Designs: Can, Annular & Can-Annular

Key Takeaways Explain This Topic AI

Combustion in gas turbine engines occurs at constant pressure (Brayton cycle isobaric process), with static pressure dropping only 1% to 3% across the burner due to friction and turbulence.

Compressor discharge air is divided into primary air (~25%) for stoichiometric combustion and secondary air (~75%) for flame centering, liner film cooling, and dilution.

Swirl vanes at the combustor snout decelerate compressor exit airflow from approximately 500 ft/s down to 50–80 ft/s, establishing a low-pressure toroidal vortex that anchors the flame front.

Interconnector tubes (flame propagation tubes) mechanically link adjacent can and can-annular liners, allowing two igniter plugs to light all combustion chambers while equalizing burner pressures.

Annular combustors deliver the highest aerodynamic efficiency, lowest pressure drop, and most uniform circumferential temperature profile into the turbine, making them standard on modern axial turbofans.

Last updated: September 2026

4.1 Combustion Section Designs: Can, Annular & Can-Annular

The combustion section is the thermodynamic heat source of the aircraft gas turbine engine. Positioned directly between the compressor diffuser and the turbine inlet guide vanes, its operational purpose is to convert chemical energy stored in aviation kerosene (Jet A or Jet A-1) into thermal energy by burning a continuous fuel-air mixture. For aviation maintenance technicians qualifying under FAA Powerplant standards (FAA-H-8083-32B), mastering combustion aerodynamics, chamber architectures, and thermal protection methods is critical for maintaining hot-section airworthiness.

Thermodynamic Principles: Isobaric Heat Addition

In the continuous-flow Brayton cycle , the combustion process is theoretically isobaric (constant pressure). Unlike reciprocating internal combustion engines where heat addition occurs at constant volume inside a closed cylinder, the gas turbine combustion chamber is open at both ends:

The upstream inlet continuously receives compressed air from the compressor diffuser.

The downstream outlet continuously discharges hot expanding gases through the turbine nozzle guide vanes.

Because the expanding gases are free to accelerate rearward into the turbine, static pressure remains essentially constant throughout combustion. In real-world operation, friction along liner walls and aerodynamic turbulence across swirl vanes and dilution ports cause a minor static pressure drop of only 1% to 3% from combustor inlet to turbine nozzle guide vane entry. This minimal pressure drop represents an unavoidable cycle loss required to induce mixing and cooling. Combustor Operating Demands:

1. Maintain stable flame without blowout across varied engine airflows and fuel flow rates.

2. Prevent metal burn-through: Gas temperatures reach 3,500°F–4,000°F while liner alloys melt around 2,400°F–2,600°F.

3. Deliver a uniform temperature profile to the turbine inlet (TIT) to prevent localized vane burn-through.

4. Complete combustion within the shortest possible axial length to minimize overall engine weight.

Primary vs. Secondary Airflow: The 25 / 75 Split

Air exiting the high-pressure compressor diffuser arrives at linear speeds between 400 and 500 feet per second (ft/s) . Aviation kerosene cannot sustain combustion at such high velocities; the flame front would be instantly blown out downstream. Therefore, the combustor diffuser first slows the air to approximately 200 to 250 ft/s , and the combustion chamber divides the incoming mass airflow into two distinct streams:

1. Primary Air (~25% of Total Airflow)

Approximately 25% of the compressor discharge air enters the forward end (dome or snout) of the combustion liner:

Stoichiometric Fuel-Air Ratio : This primary air mixes directly with atomized fuel sprayed from the fuel nozzles. Although the overall engine air-to-fuel ratio ranges from 45:1 to 130:1 (far too lean to burn), the primary zone maintains a near-stoichiometric ratio of approximately 15:1 by weight, permitting instantaneous ignition and stable burning.

Swirl Vanes & Flame Anchoring : Primary air passes through swirl vanes surrounding the fuel nozzle tip. The swirl vanes impart high-velocity rotational swirl to the incoming air, creating a low-pressure toroidal vortex (recirculation zone) along the combustor centerline. This aerodynamic vortex draws a portion of the burning gas back upstream toward the nozzle tip, continuously re-igniting incoming fuel droplets and anchoring the flame front so it cannot be swept away by the axial gas flow.

Combustion Zone Velocity : Inside this primary recirculation core, local axial velocity drops to a calm 50 to 80 ft/s , well below the turbulent flame propagation speed of kerosene.

2. Secondary Air (Cooling & Dilution, ~75% of Total Airflow)

The remaining 75% of compressor discharge air bypasses the primary flame front and flows around the exterior of the inner combustion liner:

Thermal Boundary Film Layer : Flame temperatures inside the primary combustion core reach 3,500°F to 4,000°F (1,925°C to 2,200°C) . Nickel-chromium superalloys used for combustor liners (such as Inconel, Hastelloy X, and Nimonic) lose structural integrity above 1,800°F and melt around 2,400°F to 2,600°F . To protect the liner, secondary air enters through circumferential louvers, overlapping cooling bands, and thousands of laser-drilled cooling holes. This forms a continuous, insulating boundary film of cool air along the inner liner wall, shielding the metal from radiant and convective heat.

Dilution & Temperature Profile Shaping : Further downstream, secondary air enters large dilution ports to quench the hot combustion core. This dilution process lowers the overall gas temperature to acceptable Turbine Inlet Temperature (TIT) limits (typically 1,600°F to 2,200°F , depending on turbine blade metallurgy and cooling provisions) before the gas enters the first-stage turbine nozzle guide vanes. Dilution ports are aerodynamically positioned to ensure an even circumferential temperature gradient without localized hot spots.

Loading diagram... Combustion Chamber Airflow Division & Primary Recirculation Vortex

Combustion Chamber Architectural Classifications

Turbine engines utilize four primary combustion chamber designs depending on engine size, airflow arrangement, and maintenance requirements: Multiple Can , Annular , Can-Annular , and Reverse-Flow Annular .

1. Multiple Can (Tubular) Type

The multiple can combustor consists of a circular array of individual cylindrical burner cans positioned radially around the engine drive shaft axis inside a common or individual outer shell.

Construction : Each can contains an independent outer casing and an inner perforated combustion liner with its own fuel nozzle.

Interconnectors (Flame Propagation Tubes) : Adjacent cans are joined by tubular bridges known as interconnector tubes or cross-ignition tubes. Because each can is physically separate, the engine does not require an igniter plug in every can. Typically, only two igniter plugs are installed (usually in lower cans, such as cans 3 and 7 or 4 and 8). When the igniters spark, fuel in those two cans ignites, and the flame instantaneously flashes through the interconnecting tubes to light all adjacent cans. Interconnectors also equalize combustion gas pressures between individual cans during rapid engine acceleration.

Maintenance Advantages : Individual cans can be inspected, removed, and overhauled without dismantling the turbine section or splitting major structural cases. R&D testing can be conducted on a single can test-rig.

Disadvantages : High total weight, large frontal cross-sectional area, high aerodynamic pressure losses, and uneven circumferential temperature patterns entering the turbine.

Historical Applications : Early centrifugal and axial engines (Rolls-Royce Derwent, Allison J33, General Electric J35).

2. Annular Type (Through-Flow Basket)

The annular combustor consists of a single continuous, donut-shaped flame tube (liner basket) mounted concentrically around the engine center shaft within an inner and outer casing.

Construction : Fuel nozzles (typically 12 to 30) are spaced uniformly around the circumferential dome. Only two igniter plugs are required, positioned in the lower quadrants. Once ignition occurs, the flame propagates uninterrupted around the complete annular circumference.

Aerodynamic Advantages : The annular design makes optimal use of available engine cross-section, minimizing engine diameter and total frontal drag. It provides the lowest pressure drop of any combustor design, requires less total metal surface area (saving substantial weight), and yields the most uniform circumferential temperature distribution into the first-stage turbine nozzle guide vanes, eliminating localized thermal hot spots.

Maintenance Challenges : Inspecting or replacing an annular liner requires splitting the engine structural cases and removing the turbine module, increasing labor hours during major overhauls.

Modern Applications : Nearly all modern high-bypass commercial turbofans (CFM International CFM56, General Electric GE90 / GEnx, Pratt & Whitney PW4000, Rolls-Royce Trent series).

3. Can-Annular (Cannular) Type

The can-annular design represents a mechanical hybrid that combines the structural rigidity and servicing ease of the can combustor with the aerodynamic packaging of the annular combustor.

Construction : A series of individual cylindrical flame liners (cans) are arranged radially inside a single, common outer annular casing . Compressed air enters the common outer housing and flows around all inner cans.

Flame Propagation : As with the multiple-can type, individual flame liners are interconnected by cross-ignition tubes so that two igniter plugs can initiate combustion across the entire engine.

Discharge Transition Ducts : At the aft end of each individual can, aerodynamically contoured transition ducts reshape the individual circular gas streams into a unified, continuous annular ring of gas entering the turbine nozzle guide vanes.

Operational Trade-offs : Offers superior structural hoop strength under high compressor discharge pressures (P3) and permits technician inspection of individual liners through removable casing access panels. However, it is heavier and aerodynamically more complex than a pure annular combustor.

Applications : Classic axial-flow turbojets and early turbofans (Pratt & Whitney JT3D, JT8D, J57, J75).

4. Reverse-Flow Annular Combustor

Common on small turboprop, turboshaft, and Auxiliary Power Unit (APU) engines, the reverse-flow annular combustor routes air in an S-shaped flow path.

Flow Mechanics : Compressed air discharged rearward from a centrifugal or axial-centrifugal compressor enters an outer plenum, turns 180 degrees forward into an annular combustion chamber, mixes with fuel from radial nozzles, and burns forward. The expanding exhaust gas then turns 180 degrees rearward through concentric turbine stages.

Advantages : Drastically shortens engine overall length, facilitates short, stiff rotor shafts, and allows the power turbine drive shaft to pass directly through the center of the engine without complex external ducting. It also enables highly effective inertial separation of sand, ice, and debris at the intake.

Applications : Pratt & Whitney Canada PT6A, Honeywell TPE331, and aerospace APU gas generators.

Combustor Architecture Comparison Matrix

Design Feature Multiple Can (Tubular) Annular (Through-Flow) Can-Annular (Cannular) Reverse-Flow Annular

Liner Arrangement Individual cans in individual/common housings Single continuous annular basket Individual liners in a common annular housing Single annular basket with 180° turned gas path

Interconnecting Tubes Mandatory for cross-ignition Not applicable (open continuous ring) Mandatory for cross-ignition Not applicable (continuous ring)

Igniter Plugs Required 2 plugs (propagate via interconnectors) 2 plugs (propagate circumferentially) 2 plugs (propagate via interconnectors) 2 plugs (propagate circumferentially)

Aerodynamic Pressure Loss Highest (~3% to 4%) Lowest (~1% to 1.5%) Moderate (~2% to 2.5%) Moderate (~2% to 3%)

Frontal Area & Weight Large frontal area, heaviest Smallest frontal area, lightest Moderate frontal area, intermediate weight Compact axial length, small frontal area

Turbine Entry Profile Uneven; localized hot streaks Highly uniform circumferential profile Uniform via transition ducts Highly uniform circumferential profile

Field Serviceability Individual cans removable on-wing Requires major engine case disassembly Liners removable through case access ports Compact module replacement required

Igniter Systems and Operational Duty Cycles

Unlike reciprocating engine spark plugs that fire continuously on every four-stroke cycle, gas turbine igniter plugs operate intermittently. Gas turbine combustion is self-sustaining once light-off occurs; the expanding flame continuously ignites the incoming fuel-air charge.

High-Energy Capacitor Discharge : Turbine ignition systems utilize solid-state or vibrator-type exciter boxes that store electrical energy in heavy storage capacitors, storing 4 to 12 joules of energy (FAA-H-8083-32B describes one representative storage capacitor charged to a maximum of approximately 4 joules) and dumping it through a triggering transformer that ionizes the igniter gap at a rate of 1 to 2 sparks per second. The resulting intense spark clears fuel residues, carbon deposits, and ice from the gap.

Operational Modes :

Start Mode : Igniters energized during engine cranking and de-energized automatically when the high-pressure spool reaches self-sustaining idle RPM.

Continuous Ignition : Selected manually or triggered automatically during high-risk flight phases: takeoff, landing, flight through heavy precipitation, volcanic ash, turbulent air, or when anti-ice systems are active. Continuous ignition prevents instantaneous flameout caused by airflow disruptions.

Independent FAA AMT Powerplant prep by ExamFinch. On can and can-annular engines, technicians must verify the mechanical security and internal clearance of flame interconnector tubes during hot-section inspections. Cracked or mis-seated interconnectors allow cross-bleed air leakage, resulting in failed light-offs on unignited cans, severe thermal distortion, or burner case rupture.