Study guide
7.3 Ice and Rain Control System Inspection and Limits
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
7.3 Ice and Rain Control System Inspection and Limits
Key Takeaways Explain This Topic AI
Anti-ice PREVENTS ice from forming; deice REMOVES ice after it accumulates — confusing the two leads to wrong troubleshooting.
Thermal bleed-air anti-ice routes hot compressor air through piccolo tubes in leading edges and inlets; electric heat protects pitot/static, props, windshields, and stall sensors.
Pneumatic deice boots are inflated to crack accumulated ice; cycling them too soon causes ice bridging, and only approved cleaners may touch the rubber.
TKS 'weeping wing' anti-ice pumps glycol fluid through laser-drilled titanium panels (~800 holes/in²) to depress the freezing point of impinging water.
Last updated: June 2026
Anti-Ice Versus Deice, and the Methods Tested
The first exam distinction is anti-ice versus deice . Anti-ice systems are turned on before entering icing and run continuously to prevent ice from forming — heated pitot tubes, thermal bleed-air wings, and TKS weeping wings are anti-ice. Deice systems are operated after ice accumulates to remove it — the pneumatic boot is the classic deicer. Choosing the wrong category leads to wrong operation: running a boot continuously, or cycling it before enough ice builds, allows ice bridging , where ice forms a shell over the inflated boot that later inflations cannot break.
The second distinction is what is protected: lift/control surfaces, engine inlets, air-data probes (pitot/static), stall-warning sensors, and crew visibility. Stay inside the affected boundary — a failed wiper does not prove a pitot-heat fault, and a dead pitot-heat circuit does not prove a boot problem.
Thermal bleed-air anti-ice extracts hot air from a turbine engine's compressor and routes it through perforated piccolo tubes inside wing, stabilizer, and inlet leading edges; ejectors mix bleed air with cooler ram air to control temperature. It requires extensive ducting, control valves, and overheat protection, and bleed leaks are an inspection item. Electric (electrothermal) heat powers resistance elements in pitot tubes, static ports, stall vanes, propeller boots (via slip rings/brushes), and heated windshields.
Pneumatic deice boots are rubber leading-edge coverings with internal bladders that inflate from an engine-driven air pump (or vacuum/regulated pressure) to crack ice, then deflate flush. TKS weeping wing is a fluid anti-ice/deice system: a pump forces glycol-based fluid through formed titanium panels laser-drilled with roughly 800 tiny holes per square inch ; the fluid weeps out, coats the leading edge, propeller, and windshield, and lowers the freezing point of impinging water so it runs off without freezing.
- System Anti-ice or deice Method Maintenance caution
- Heated pitot/static Anti-ice Electric resistance Burn hazard; verify current draw/heat by procedure
- Thermal bleed-air Anti-ice Hot compressor air in piccolo tubes Inspect ducts/valves for leaks; hot surfaces
- Pneumatic boots Deice Inflatable bladders crack ice Approved cleaners only; check cuts/bond/leaks
TKS weeping wing Anti-ice/deice Glycol fluid through laser-drilled panels Correct fluid, panel cleanliness, pump/filter
Heated windshield Anti-ice/rain Embedded element Approved cleaning; no localized overheat
Rain Control and Inspection Limits
Rain control protects visibility by three approved means. Windshield wipers clear water mechanically; blades must match the windshield, park correctly, and sweep within the designed arc — a wiper that parks wrong can block vision or scratch the transparency, and wipers are not used on dry glass. Chemical rain repellent (or hydrophobic surface coatings) causes water to bead and blow off; only the approved fluid/coating may be used, because incompatible chemicals attack transparencies.
Pneumatic rain removal blows a sheet of high-velocity (often heated) air across the windshield to push water off, common on jets. Windshield alcohol systems spray isopropyl alcohol for combined anti-ice and rain repellency on some aircraft. Heated windshields also keep the panel above the freezing/fogging point and warm it for bird-strike resilience.
Pneumatic boots are easily ruined by poor practice: petroleum products and unapproved solvents attack the rubber, and scrapers cut the surface, so only the cleaner specified in the maintenance manual is used. When a boot inflates weakly, separate the air source, timer/distributor (control) valve, plumbing, clamps, check valves, leaks, and boot condition before replacing the visible boot — the fault is often upstream.
Electric ice protection adds burn hazards : a heated pitot tube can reach skin-burning temperature within seconds of power-on, and ground operation of pitot heat is time-limited. Troubleshoot electric heat by verifying breaker, power, switch, control, wiring, ground, and element resistance against approved data before condemning a "cold" probe.
- Rain/visibility system How it works Key limit
- Wipers Mechanical sweep Match blade/arc; never run dry; check park
- Chemical repellent Beads water for blow-off Approved fluid/coating only
- Pneumatic rain removal High-velocity air sheet Correct air source/nozzle operation
- Alcohol spray Isopropyl anti-ice/repellent Approved fluid; flow/nozzle check
- Ice Detection and System Components
Many aircraft carry ice detectors that alert the crew or automatically trigger protection: a vibrating-probe detector senses ice mass by a change in its resonant frequency, while optical detectors sense ice optically. The mechanic checks detector security, heating, and test response by procedure. Engine inlet anti-ice (bleed-air or electric) protects the inlet lip and probes so ingested ice cannot damage compressor blades — a powerplant-related but airframe-routed system.
The pneumatic-boot system has identifiable parts worth knowing: an engine-driven air pump (often the same pump that supplies vacuum instruments, with pressure tapped off), a regulator and relief valve, a distributor/timer (control) valve that sequences inflation, check valves to hold boot deflation by vacuum, and the boots themselves bonded to the leading edge. Boots are normally held deflated against the airfoil by suction so they do not disturb airflow in clear air; they inflate only on command. When inflation is weak or uneven, the timer/distributor and air supply are checked before the boot is condemned.
- Boot-system part Function
- Air pump Supplies inflation pressure
- Distributor/timer valve Sequences and times boot inflation
- Check valve Holds boots deflated by vacuum
- Regulator/relief valve Limits inflation pressure
The consistent exam theme: identify the installed system, classify it as anti-ice or deice, use its specific procedure, and avoid any action that damages the protected surface. A mechanic does not release an ice-protection system based on general weather knowledge — the task is to confirm the installed system meets the instructions for continued airworthiness through operational checks, resistance/current checks, pressure checks, plumbing and boot inspection, and approved cleaning.
A common exam trap is assuming a "cold" heated probe is failed: verify breaker, switch, control logic, wiring, ground, and element resistance first, because the element itself is frequently not the fault.