Study guide
5.4 Flight Control Systems, Rigging, and Travel
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
5.4 Flight Control Systems, Rigging, and Travel
Key Takeaways Explain This Topic AI
Primary controls (aileron, elevator, rudder) move the aircraft about its three axes; secondary/auxiliary controls (flaps, trim tabs, slats, spoilers) change lift, drag, trim, or handling.
Control runs use cables with turnbuckles, pulleys, fairleads, bellcranks, and push-pull (torque) tubes; cable tension is set with a tensiometer and turnbuckles and corrected for temperature.
Rigging means setting controls to the neutral/streamline reference, then adjusting stops and tension so travel matches the manufacturer's degrees, verified with a protractor or rig pins.
Direction of movement must be independently confirmed (stick right = right aileron up / left aileron down; right rudder = rudder right), because a reversed control is catastrophic.
Turnbuckles must be safetied and within the unscrewed-thread limit (no more than three threads showing), and travel/tension are rechecked after any control work.
Last updated: June 2026
Primary, Secondary, and Auxiliary Controls
Flight controls are grouped by what they do:
- Group Surfaces Axis / effect
- Primary Ailerons Roll about the longitudinal axis
- Elevator (or stabilator) Pitch about the lateral axis
- Rudder Yaw about the vertical axis
- Secondary Trim tabs Relieve control pressure (trim)
- Auxiliary Flaps, slats, spoilers/speedbrakes Increase lift/drag, control descent/roll
The three primary surfaces move the aircraft about its three axes; remember the matchup of axis to motion. Trim tabs (and balance, servo, anti-servo tabs) reduce pilot effort. Flaps (plain, split, slotted, Fowler) increase lift and drag for takeoff/landing; slats/slots energize airflow at high angle of attack; spoilers dump lift and can assist roll. Differential and Frise ailerons reduce adverse yaw — knowing the type explains the rigging and the inspection focus.
The Mechanics of a Control Run
Controls are moved by cable systems or push-pull (torque) tube systems (and on transports, hydraulic actuators). A cable run includes:
Control cables — usually 7×19 (flexible, over pulleys) or 7×7 (less flexible) corrosion-resistant or carbon steel wire rope.
Turnbuckles — adjust cable length/tension; have a barrel with right- and left-hand threads.
Pulleys and fairleads — change cable direction and support it; check for worn flat spots, frozen bearings, and cable rubbing.
Bellcranks, quadrants, and push-pull rods — convert and transmit motion.
Inspect a control run as a system : frayed/corroded cable (run a cloth along it to snag broken wires — replace per the broken-wire-per-inch limit), worn pulleys, loose rod-end bearings (check rod-end thread engagement via the inspection hole — a wire that won't pass means enough threads are engaged), and proper safetying. Cable wear, a seized pulley, or a loose rod end can cause binding, lost motion, or jamming that only shows up under full deflection and load.
Setting Cable Tension
Cable tension is measured with a tensiometer fitted with the correct riser for the cable size; the dial reading is converted to pounds using the instrument's calibration chart . Because steel cable expands and contracts with temperature, tension must be set using a temperature-correction (rigging) chart — you read ambient temperature and cable size to find the target tension, so a system rigged on a cold morning is not over-tight at noon.
Procedure for tensioning: support/neutralize the surface, adjust the turnbuckles to bring tension to the charted value at the given temperature, keep the two cables of a pair balanced, then safety the turnbuckles (clip type or double-wrap wire). A turnbuckle is in tolerance when no more than three threads are exposed outside the barrel on either end — more than that means the cable assembly is the wrong length. Over-tension causes drag, pulley/bearing wear, and high control forces; under-tension causes slack, lost motion, and cable jumping a pulley.
Rigging and Verifying Travel
Rigging sets each surface to its correct neutral position and travel:
Place flight controls at neutral/streamline using the manufacturer's rig pins, blocks, or index marks in the cockpit and at the surface.
Adjust push-pull rods/turnbuckles so neutral lines up at both ends simultaneously.
Set control stops so the surface reaches — but does not exceed — the specified degrees of travel up/down or left/right.
Measure travel with a universal propeller/control protractor or a rig fixture, comparing against the maintenance manual's degree limits.
Confirm cable tension at temperature and recheck for full, free, correct movement.
The single most important verification is direction of movement : with the stick moved right, the right aileron goes up and the left aileron goes down ; pulling back raises the elevator (pitch up); right rudder pedal moves the rudder right. A reversed control — easy to create by crossing cables or installing a pushrod backward — is catastrophic, so direction is checked independently by a second person or against the manual before flight. After any control-system work, a required operational check confirms full travel, free movement, correct direction, and no binding through the entire range — never just at neutral.
Cable Inspection Limits and Troubleshooting
Control cables are a graded inspection item with hard limits. Run a cloth slowly along the cable to snag broken wires ; a cable is rejected when broken wires exceed the allowable count (commonly stated as a maximum number per a given length, such as per inch), and it is automatically rejected at critical fatigue and fairlead points where wear concentrates. Look for corrosion (internal corrosion is hidden — twist the cable open gently at suspect spots), kinks, bird-caging, flat spots, and wear where the cable rides pulleys.
Pulleys must turn freely (a flat-spotted or frozen pulley wears cable fast and signals a seized bearing), and the cable must ride in the groove — a misaligned pulley or worn fairlead lets the cable saw against structure.
Troubleshooting a control complaint follows the system. A stiff or binding control points to over-tension, a seized pulley/bellcrank bearing, a dragging fairlead, or interference; excess play or sloppy feel points to under-tension, worn rod ends, or stretched cable. A control that reaches a stop early or late is a rigging or stop-adjustment problem, not a strength problem.
Because each fault has a different cause, the technician confirms tension at temperature, free pulley rotation, secure stops, and correct travel and direction together. A worked check: if measured aileron travel is short of the manual's degrees, verify the surface truly reaches the control stop (not a cable hitting a fairlead), confirm rig-pin alignment at neutral, and only then re-adjust the pushrod or stop — never force more travel by loosening a stop beyond its limit, which would let the surface overtravel and load the structure abnormally.
Reassembling, re-rigging, and re-checking as a system is the safe habit.