Study guide
5.1 Metallic Structure Inspection and Damage Patterns
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
5.1 Metallic Structure Inspection and Damage Patterns
Key Takeaways Explain This Topic AI
Stressed-skin structure is either monocoque (skin carries all loads) or, far more commonly, semimonocoque (skin plus longerons, stringers, frames, and bulkheads share the load).
Structure carries five basic stresses — tension, compression, shear, bending, and torsion — and the damage you find is a clue to which load path is overworked.
Inspection method follows the material: dye penetrant and eddy current work on aluminum, while magnetic particle is for ferromagnetic (steel) parts only.
Classify the defect (crack, dent, scratch, corrosion, elongated hole, smoking rivet, heat damage), then compare it to approved limits in the SRM/AMM before choosing any repair.
Heat damage can ruin aluminum temper and strength even when the surface looks perfect, so appearance alone never clears a part for return to service.
Last updated: October 2026
How Airframe Structure Carries Load
Almost every metal airplane uses stressed-skin (monocoque or semimonocoque) construction . In a pure monocoque structure the external skin alone carries the loads — there is no internal bracing — so any skin dent or crack is structurally significant and the design is heavy for its strength.
Because monocoque skins must be thick to resist buckling, aircraft instead use semimonocoque construction almost universally: the skin still carries load, but it is supported by longerons and stringers (running lengthwise) and frames, formers, and bulkheads (running around the cross-section). This lets the skin be thin while the substructure handles bending and keeps the shape.
The major airframe assemblies are the fuselage (longerons, stringers, frames, bulkheads, skin), the wing (front and rear spars , ribs , stringers, and skin), and the empennage (the vertical and horizontal stabilizers with their own spars and ribs). A bulkhead is a heavy frame that divides the fuselage or anchors major loads such as a wing attach or pressurization dome. Knowing what part you are looking at tells you the load it carries and therefore how seriously to treat damage.
The Five Stresses and What Damage Reveals
Structure must resist five basic stresses, and damage patterns point to which one is being overworked:
- Stress Definition Typical airframe example
- Tension Pulling apart Lower wing skin in flight; cables under load
- Compression Squeezing/crushing Upper wing skin in flight; landing-gear struts
- Shear Forces sliding parallel layers Rivets and bolts cut across the joint
- Bending Combined tension + compression Wing spar (top compressed, bottom in tension)
- Torsion Twisting Engine crankshaft; wing under aileron load
Most rivets and bolts in a sheet-metal joint are loaded in shear , which is why fastener selection and edge distance matter. A wing spar in bending has its cap in tension on one face and compression on the other, so a crack on the tension side grows fast. Reading a damage scenario as a load-path question — not just a cosmetic one — is the core skill the Airframe test rewards.
Inspecting and Classifying Defects
Nondestructive inspection (NDI) method must match the material and the suspected defect:
Visual / magnification / borescope — first line for cracks, corrosion, loose fasteners.
Dye (liquid) penetrant — surface-breaking cracks in nonporous, nonmagnetic metals (aluminum, magnesium, some stainless).
Eddy current — surface and near-surface cracks in conductive metals; great around fastener holes.
Magnetic particle — surface/subsurface flaws in ferromagnetic (steel) parts only — it will NOT work on aluminum.
Ultrasonic — subsurface flaws and thickness.
Radiographic (X-ray) — hidden internal defects and corrosion, with strict safety controls.
Classify what you find: a crack grows under cyclic load and is normally serious; a smoking rivet (dark teardrop streak) or fretting indicates a working/loose joint; an elongated hole has lost bearing area and clamp-up; a scratch is judged by depth, direction, and location; heat damage can alter aluminum temper even when the shape is normal. A repair material is acceptable only when alloy, temper, thickness, grain direction, and fastener compatibility match the approved data — strength alone is not enough.
A Disciplined Decision Sequence
Use the same logic on every metallic-structure scenario:
Identify the structure and its likely load path (tension/compression/shear/bending/torsion).
Clean enough to inspect without needlessly stripping protective finish.
Classify the defect type and measure it.
Compare to the Structural Repair Manual (SRM) , aircraft maintenance manual (AMM), service bulletins, and airworthiness directives .
Decide whether the damage is within published negligible/repairable limits or requires approved engineering data (a DER/8110-3 or manufacturer approval).
Document the finding, the data used, and the result.
Sheet-metal work also creates hazards the ACS risk elements expect you to manage: burrs cut hands and start cracks, drill chips fly into eyes (wear eye protection), compressed air and pneumatic tools must be controlled, and an incompatible repair material can set up galvanic corrosion. Exam questions frequently hide the key in the location of the damage — a mark near a spar cap, bend radius, bulkhead, or hinge deserves far more caution than the same mark on an unstressed fairing.
When in doubt, choose the answer that inspects first, uses current approved data, preserves temper and load path, and never returns a part to service on appearance alone.
Common Exam Traps and Worked Logic
Several recurring traps appear in metallic-structure questions. First, strength is not the only criterion for a repair material: a replacement skin must match the original alloy and temper (for example, 2024-T3 versus 7075-T6), the correct thickness or one gauge thicker if the data allows, the grain direction when forming bend radii, and fastener compatibility to avoid galvanic action. A part that is merely 'as strong' but a different alloy can corrode, fatigue, or fail to flex with the surrounding structure.
Second, negligible damage is defined by the data, not by feel — the SRM states the exact dent depth, scratch length, and edge-distance reductions that may be left unrepaired or simply blended out and re-protected.
A short worked case shows the load-path mindset. Suppose a 0.040-inch lower wing skin (a tension-loaded surface in flight) has a crack running spanwise from a fastener hole. Because the lower skin is in tension during normal flight, the crack will propagate under cyclic load; this is not a candidate for a quick cosmetic fix.
The correct sequence is to stop-drill the crack tip only if the SRM authorizes it as an interim step , inspect the surrounding holes with eddy current for additional cracking, and then install the manufacturer's approved patch — typically a doubler that re-establishes the rivets the crack interrupted, in the same alloy and gauge. Choosing eddy current (not magnetic particle) is itself a tested point, because the skin is aluminum .
The disciplined order — identify load path, classify, inspect with the right method, repair only within approved limits, document — is exactly what distinguishes the airworthy answer from the tempting shortcut.