Study guide
3.1 Electricity and Electronics Foundations
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
3.1 Electricity and Electronics Foundations
Key Takeaways Explain This Topic AI
Ohm's Law (E = I x R) and Watt's Law (P = I x E) are the two relationships every General test item builds on; rearrange them to find any unknown.
Series circuits share one current and add resistances and voltage drops; parallel circuits share one voltage and add currents, with total resistance always smaller than the smallest branch.
Capacitors store charge in an electric field and oppose voltage change; inductors store energy in a magnetic field and oppose current change.
Aircraft DC sources are lead-acid or nickel-cadmium batteries rated in volts and amp-hours; cells in series add voltage, cells in parallel add capacity.
Electrostatic discharge (ESD) precautions protect solid-state and avionics components that fail at voltages a technician cannot feel.
Last updated: September 2026
Electron Theory and the Four Circuit Quantities
Electricity is the flow of electrons through a conductor. The FAA General (AMG) knowledge test treats four quantities as the backbone of every electrical question:
- Quantity Symbol Unit What it describes
- Voltage (EMF) E (or V) volt (V) Electrical pressure that pushes electrons
- Current I ampere (A) Rate of electron flow (1 A = 1 coulomb/sec)
- Resistance R ohm (Omega) Opposition to current flow
- Power P watt (W) Rate of doing electrical work
Conductors (copper, aluminum) have many free electrons; insulators (rubber, glass, most plastics) have very few. A semiconductor such as silicon sits between the two and is the basis of diodes, transistors, and the solid-state devices in modern avionics. A diode allows current in one direction only (used to rectify AC to DC and to block reverse current); a transistor acts as an electronic switch or amplifier. Conventional current is drawn from positive to negative, while electron flow is negative to positive; the FAA uses conventional current in its schematics, so study to that convention.
The General curriculum also touches digital fundamentals : the binary number system (only 0 and 1) underlies digital logic and computers, and basic logic gates (AND, OR, NOT) combine binary inputs. You will not design circuits, but you must recognize that modern aircraft systems are largely digital and that a single bit represents on/off, true/false, or high/low.
Ohm's Law and Watt's Law (Worked Examples)
Ohm's Law states E = I x R (voltage equals current times resistance). Rearranged: I = E / R and R = E / I. Watt's Law states P = I x E (power equals current times voltage); combined with Ohm's Law it also gives P = I^2 x R and P = E^2 / R. Memorize the wheel; most General items are one substitution.
Worked Ohm's-Law example: A 28-volt aircraft DC bus feeds a landing-light circuit with 4 ohms of total resistance. Current = E / R = 28 / 4 = 7 amperes . The power dissipated = I x E = 7 x 28 = 196 watts (check: I^2 x R = 49 x 4 = 196 W, agrees). If a technician sizes a circuit breaker, the 7-amp draw means a 10-amp breaker is reasonable, not a 5-amp one.
Second example: A bulb draws 0.5 A from a 14-volt system. Its resistance = E / I = 14 / 0.5 = 28 ohms , and it consumes P = I x E = 0.5 x 14 = 7 watts . Common trap: candidates divide volts by watts or mix a 14-volt and 28-volt system. Always write the formula, insert units, then solve.
Series, Parallel, and Combined Circuits
The rules differ by topology and are a frequent test trap:
- Rule Series circuit Parallel circuit
- Current Same through every component Splits; branch currents add to source current
- Voltage Drops add to source voltage Same across every branch
- Resistance R_total = R1 + R2 + R3 ... R_total = 1 / (1/R1 + 1/R2 + ...)
In a series circuit the total resistance is the simple sum, and the individual voltage drops must add up to the source voltage (a form of Kirchhoff's Voltage Law). Worked series example: three resistors of 2, 3, and 5 ohms in a 20-volt circuit give R_total = 10 ohms, so I = 20 / 10 = 2 A, and the drops are 4 V, 6 V, and 10 V (which sum to 20 V).
In a parallel circuit total resistance is always less than the smallest branch . Worked parallel example: two 6-ohm resistors in parallel give R = 1 / (1/6 + 1/6) = 1 / (2/6) = 3 ohms . The branch currents add (Kirchhoff's Current Law). Most aircraft loads are wired in parallel across the bus so each operates at full bus voltage and one failure does not open the others.
Capacitance, Inductance, Batteries, and ESD
A capacitor stores energy in an electric field between two plates separated by a dielectric; capacitance is measured in farads (usually microfarads in aircraft). A capacitor opposes a change in voltage and blocks DC while passing AC. An inductor (coil) stores energy in a magnetic field, is measured in henrys , and opposes a change in current ; it passes DC but chokes AC. These reactive behaviors set up the AC topics in the next section.
Aircraft DC is supplied by lead-acid or nickel-cadmium (Ni-Cad) storage batteries rated in volts and amp-hours (capacity). A lead-acid cell is nominally about 2 volts , while a Ni-Cad cell is nominally about 1.2 volts ; use the manufacturer’s specified values when testing or charging. Cells in series add voltage ; cells in parallel add capacity (amp-hours) at the same voltage. So six 2-volt cells in series make a 12-volt battery, while two 12-volt 25-amp-hour batteries in parallel still read 12 volts but supply 50 amp-hours. Ni-Cad batteries can suffer thermal runaway and require different servicing, charging, and capacity-check procedures than lead-acid.
Magnetism and electromagnetic induction also belong in this foundation: current flowing through a conductor creates a magnetic field, and a magnetic field moving relative to a conductor induces a voltage. This is the basis of generators, alternators, motors, relays, and solenoids found throughout the aircraft. The strength of an electromagnet grows with current and the number of turns of wire.
Circuit Protection and ESD
Every aircraft circuit includes protection sized to the wire, not the load: a fuse melts open on overcurrent, while a circuit breaker trips and can be reset. The protective device guards the wiring from overheating during a short or overload, so a tripped breaker is a symptom to investigate, not merely reset repeatedly.
Electrostatic discharge (ESD) can destroy semiconductors and avionics modules at voltages far below what a person can feel (a perceptible spark is thousands of volts; many devices fail below 100 volts). Use grounding wrist straps, conductive mats, and approved static-shielding packaging when handling solid-state line-replaceable units. ESD awareness is now squarely in the General curriculum, not just advanced avionics study.