Study guide
3.5 Maintenance Math and Unit Discipline
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
3.5 Maintenance Math and Unit Discipline
Key Takeaways Explain This Topic AI
Order of operations (parentheses, exponents, multiply/divide, add/subtract) and rounding only at the end prevent plausible but wrong answers.
Area of a rectangle is length x width and of a circle is pi x r^2; volume of a box is l x w x h and of a cylinder is pi x r^2 x h.
Ratios and proportions solve mixing, gearing, and scaling problems; a percentage is a ratio expressed per hundred.
One inch equals 25.4 mm exactly; 1 US gallon = 231 cubic inches; AN/AC fitting and tubing sizes are stated in sixteenths of an inch.
The safe process is identify the formula, convert all units, solve, then round and sanity-check the answer's magnitude.
Last updated: June 2026
Arithmetic Discipline: Order of Operations and Rounding
Maintenance math fails most often not from hard formulas but from sloppy process. Follow order of operations - parentheses, then exponents, then multiplication and division left to right, then addition and subtraction (PEMDAS). Evaluating 2 + 3 x 4 as 20 instead of 14 is a classic trap.
Signed numbers matter in W&B (forward arms are negative) and temperature work: a negative times a negative is positive, and subtracting a negative adds. Round only at the very end and to the precision the task needs; rounding mid-calculation compounds error. Scientific notation (writing 6,700 as 6.7 x 10^3) keeps large and small numbers manageable - move the decimal and adjust the exponent, adding exponents when multiplying powers of ten. Express fractions and decimals interchangeably; many aircraft dimensions are fractional (1/16 in) while instruments read decimals.
The recommended workflow is identify the formula, convert units first, solve, round last, then sanity-check the magnitude against reality.
Worked conversion: because 1 in = 25.4 mm exactly, a 3.500-in bore measured in metric tooling is 3.500 x 25.4 = 88.9 mm ; reversing it, an 88.9 mm reading divided by 25.4 returns 3.500 in. Worked displacement: total engine displacement is the single-cylinder swept volume (pi x r^2 x stroke) times the number of cylinders, so a four-cylinder engine with a 5.125-in bore (r = 2.5625 in) and 4.375-in stroke displaces pi x 2.5625^2 x 4.375 x 4 = about 361 cubic inches .
Geometry: Areas and Volumes
Mechanics compute areas (wing area, sheet-metal patch coverage) and volumes (fuel tanks, baggage bays):
- Shape Formula
- Rectangle area length x width
- Triangle area 1/2 x base x height
- Circle area pi x r^2 (r = radius; pi ~ 3.1416)
- Rectangular solid volume length x width x height
- Cylinder volume pi x r^2 x height
Worked volume example: a cylindrical tank 10 in in diameter and 20 in long holds pi x r^2 x h = 3.1416 x (5)^2 x 20 = 3.1416 x 25 x 20 = 1,570.8 cubic inches . Converting to gallons (231 in^3 per US gallon): 1,570.8 / 231 = 6.8 gallons . Two common errors are using the diameter instead of the radius (radius is half the diameter) and forgetting to square the radius. For a circle, doubling the radius quadruples the area because the radius is squared - a useful reasonableness check.
Ratios, Proportions, and Percentages
A ratio compares two quantities (for example a compression ratio of 8:1 means cylinder volume at bottom dead center is eight times the volume at top dead center). A proportion sets two ratios equal and is solved by cross-multiplying: if 2 oz of additive treats 10 gal, then x oz treats 25 gal gives x = (2 x 25) / 10 = 5 oz . Gearing, mixing, and scale-drawing problems are all proportions.
A percentage is simply a ratio expressed per hundred, so you convert by multiplying a decimal by 100 (0.05 = 5%) or dividing a percent by 100 to use it. For example, an aircraft loaded to 2,070 lb against a 2,300 lb maximum gross weight is at 2,070 / 2,300 = 90% , leaving 230 lb (10%) of margin. Percent-of-change problems (wear, growth) divide the change by the original value. Keep the base consistent - taking a percentage of the wrong total is a frequent mistake.
Units, Conversions, and Aircraft Hardware Sizing
Unit discipline prevents answers that are numerically right but dimensionally wrong:
- Conversion Value
- Inch to millimeter 1 in = 25.4 mm (exact)
- US gallon to cubic inches 1 gal = 231 in^3
- Pound to ounce 1 lb = 16 oz
- Foot to inch 1 ft = 12 in
- Horsepower to foot-pounds/min 1 hp = 33,000 ft-lb/min
AN and AC hardware sizes follow a dash-number convention: fluid-line fittings and tubing are sized in sixteenths of an inch by their dash number, so a -6 fitting is 6/16 = 3/8 in tube outside diameter. AN bolt diameters likewise use sixteenths (an AN4 bolt is 4/16 = 1/4 in), and the bolt's grip/length is given by a second number. Torque conversions matter when a wrench reads inch-pounds but the spec is foot-pounds (1 ft-lb = 12 in-lb), and applying foot-pound numbers to an inch-pound spec over-torques fasteners twelve-fold.
When a problem mixes metric and US units, convert everything to one system before computing , then convert the final answer back if needed.
Compression Ratio and Reasonableness Checks
Compression ratio , a recurring example, is the ratio of cylinder volume with the piston at bottom dead center to the volume at top dead center: if total volume is 80 in^3 and clearance volume is 10 in^3, the ratio is 80 / 10 = 8:1 . Ratios have no units because the units cancel. Finally, build the habit of a reasonableness check : estimate the answer's order of magnitude before trusting the calculator. A fuel tank that computes to 600 gallons in a light aircraft, or a torque of 3 in-lb on a main bolt, signals a units or decimal error.
In maintenance, an arithmetic slip is not abstract - it can mean an out-of-limits part is accepted or a fastener is set to the wrong torque, so the discipline of identify-convert-solve-round-check is itself a safety practice.