Study guide
10.2 Carburetors, Fuel Injection, and Metering Logic
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
10.2 Carburetors, Fuel Injection, and Metering Logic
Key Takeaways Explain This Topic AI
Float-type carburetors meter fuel using the pressure drop in a venturi while a float-and-needle valve holds a constant bowl level; pressure carburetors meter by air/fuel pressure differentials and resist icing/attitude better.
Carburetor ice forms three ways - fuel-evaporation ice, throttle ice, and impact ice - and can occur in the venturi at outside air temperatures up to about 70 F with high humidity because the venturi can drop air temperature by roughly 70 F.
Continuous-flow Bendix/Precision RSA fuel injection uses an air-metering throttle/regulator, a flow divider (spider) with anti-drip idle cutoff, and air-bleed nozzles at each cylinder.
Fuel injection advantages: less induction icing, better fuel distribution, improved acceleration, reduced overheating, and better fuel economy.
Mixture is read through EGT/CHT, roughness, fuel flow, and throttle response - leaning raises EGT to peak then lowers it past peak, and a single blocked nozzle leans only its cylinder.
Last updated: October 2026
Carburetors: Venturi, Float, Mixture, and Idle Cutoff
A fuel metering system must deliver the correct fuel mass for the air entering the engine. Too much fuel cools combustion but wastes fuel, fouls plugs, and lowers power; too little fuel raises temperatures and increases detonation risk before misfire. Float-type carburetors meter fuel using the pressure differential created when intake air accelerates through a venturi : the throat is the narrowest point, where velocity is highest and static pressure is lowest, so the low pressure at the main discharge nozzle draws fuel from the float bowl.
A float and needle valve hold a constant fuel level in the bowl (vented near atmospheric) so metering stays calibrated. The mixture control adjusts fuel for air density; pulling it to idle cutoff shuts off fuel at the metering jet so the engine is always stopped with a lean cutoff, clearing fuel from cylinders and preventing run-on.
At closed/idle throttle little air moves through the venturi, so an idle/off-idle circuit supplies fuel from below the throttle plate where manifold suction is high. The accelerating pump adds a momentary fuel shot on rapid throttle opening to prevent a lean stumble, and an economizer (power enrichment) valve adds fuel at high power. Pressure carburetors (for example, Bendix-Stromberg) instead meter by balancing air-impact and fuel pressures across a regulator and a poppet valve.
Because fuel is delivered under positive pressure rather than drawn by venturi suction, pressure carburetors are far less prone to carburetor icing and tolerate aircraft attitude/maneuvers better than float types.
- Feature Float-type carburetor Pressure carburetor / fuel injection
- Fuel delivery Venturi suction draws fuel from a vented bowl Positive fuel pressure across regulator/nozzles
- Icing tendency High (fuel-evaporation + venturi cooling) Low (no bowl, less evaporative cooling in throat)
- Attitude/maneuver sensitivity Sensitive (bowl can slosh) Tolerant (no float bowl)
- Distribution Single discharge; uneven cylinder-to-cylinder Individual nozzle per cylinder, even distribution
- Idle cutoff Mixture-control jet cutoff Flow-divider anti-drip / idle cutoff
Carburetor Ice, Carb Heat, and Continuous-Flow Injection
Carburetor icing has three forms per FAA AC 20-113. Fuel-evaporation ice forms where fuel vaporizes and cools the air; it can occur at outside temperatures from roughly +20 F to +80 F (about -4 C to +27 C). Throttle ice forms at or near a partly closed throttle plate where the venturi-plus-throttle pressure drop chills moist air; it is common at low power. Impact ice forms when moist air below freezing strikes screens, scoops, and the heat valve, most rapidly near 25 F.
The venturi can drop air temperature about 70 F (39 K) , so ice is possible even on a warm day with high humidity. Ice narrows the throat, so airflow falls and the mixture often enriches because metering does not drop proportionally; a fixed-pitch aircraft loses RPM, a constant-speed aircraft loses manifold pressure.
Carburetor heat routes air through an exhaust heat-stove/shroud to melt ice and prevent formation; because warm air is less dense it lowers power and richens the mixture, and applying heat can briefly worsen roughness as melted water passes through.
Continuous-flow fuel injection (Bendix/Precision RSA series) is a multi-cylinder system that meters fuel by sensing engine airflow. Air mass is measured at the throttle/air-metering body , the fuel regulator sets fuel pressure proportional to airflow, the flow divider (spider) distributes fuel to each cylinder and provides a clean anti-drip idle cutoff , and air-bleed nozzles at each cylinder head spray fuel into the intake port. Fuel flow indication is read at the divider as a pressure proportional to flow.
Compared with carburetors, fuel injection offers less induction icing (no venturi cooling in a fuel-laden throat), better fuel distribution to all cylinders, improved acceleration from positive metering, reduced overheating , and better fuel economy .
A mixture/metering checklist:
Determine whether the fault is all cylinders or one cylinder.
Compare fuel pressure, fuel flow, RPM/manifold pressure, EGT, and CHT.
Inspect for induction leaks, carburetor ice, blocked jets/nozzles, float problems, and rigging.
Consider recent maintenance - linkage travel and nozzles are easily disturbed.
Use approved data; small metering changes cause large temperature and power effects.
The shortcut is to ask what changed first - air, fuel, or control position. Ice reduces air; a blocked nozzle starves one cylinder; an intake leak adds unmetered air (lean); a stuck enrichment circuit adds fuel (rich). Leaning toward peak EGT raises EGT until peak, then lowers it past peak as combustion efficiency falls.
Several exam traps recur. First, carburetor heat is hot, unfiltered air , so it richens the mixture and lowers power even when no ice is present - that is normal, not a fault. Second, the mixture enriches with carburetor ice; candidates who answer "leaner" miss that fuel metering does not fall as fast as the airflow restriction. Third, a fixed-pitch aircraft signals ice with falling RPM , while a constant-speed aircraft signals it with falling manifold pressure , because the governor holds RPM constant.
Fourth, an induction air leak and a lean fuel-metering fault both produce a lean cylinder, but only the air leak adds unmeasured air - the distinction drives the repair. Finally, pressure carburetors and injection systems are chosen partly because they largely eliminate the venturi-cooling icing that plagues float carburetors.