Study guide
10.6 Propeller Systems, Governors, and Inspection
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
10.6 Propeller Systems, Governors, and Inspection
Key Takeaways Explain This Topic AI
Blade angle (pitch) is the angle of the chord to the plane of rotation; angle of attack is the angle between the chord and the relative wind, which depends on both RPM and forward speed.
A constant-speed governor uses RPM-driven flyweights and a pilot valve to meter ~boosted engine oil to the pitch-change piston, holding the selected RPM as load changes.
Centrifugal twisting moment (CTM) is the strongest blade force and drives blades toward low pitch; aerodynamic twisting moment (ATM) is smaller and drives toward high pitch.
Feathering streamlines a dead-engine blade to near 90 degrees to cut drag; reversing/beta uses negative blade angle for ground deceleration and must be locked and rigged correctly.
Propeller inspection prevents fatigue failure - nicks, cracks, corrosion, erosion, and delamination are stress risers; blending and track/balance must follow approved limits.
Last updated: June 2026
Blade Angle, Angle of Attack, and the Governor
A propeller is a rotating airfoil that converts engine torque into thrust. Two angles must be distinguished. Blade angle (pitch) is the angle between the blade chord and the plane of rotation , measured at a reference station (usually 75% radius); it is set by the hub/governor. Angle of attack (AOA) is the angle between the chord and the relative wind , which is the resultant of rotational velocity and forward (flight) velocity.
Because forward speed changes the relative wind, AOA changes with airspeed even when blade angle is fixed - the reason a fixed-pitch propeller is efficient only near one airspeed/RPM combination and lets RPM rise and fall directly with power and airspeed. A constant-speed propeller varies blade angle to hold a selected RPM: low pitch (fine) for takeoff/acceleration, high pitch (coarse) for cruise efficiency.
The governor is the heart of a constant-speed system. Flyweights spun by the engine sense RPM and tilt against a speeder spring whose tension the pilot sets with the propeller control. A pilot valve attached to the flyweights ports engine oil - boosted by a governor gear pump to roughly 200-300 psi - to or from the propeller hub piston:
On-speed: flyweight force balances spring force, the pilot valve is centered, oil is trapped, and blade angle holds.
Overspeed: RPM rises, flyweights tip out, the pilot valve rises and ports oil to increase blade angle (coarser pitch), which absorbs more power and brings RPM back down.
Underspeed: RPM falls, flyweights drop in, the pilot valve releases oil and a counterweight/spring (or oil, depending on design) moves blades finer to restore RPM.
- Propeller type or part Function Fault effect
- Fixed-pitch propeller Blade angle set by design RPM varies directly with power and airspeed
- Constant-speed governor Meters oil to change blade angle Hunting, overspeed, underspeed, sluggish response
- Feathering system Blades to ~90 deg, low drag Failure to feather/unfeather affects shutdown/restart/drag
Reversing (beta) system Negative blade angle for deceleration Rigging/lock faults create thrust-asymmetry hazards
Blade/leading edge Airfoil shape and strength Nicks/cracks/corrosion/erosion seed fatigue cracks
Twisting Forces, Feathering, Reverse, and Inspection
Four forces act on a turning blade. Centrifugal force tries to throw the blade out of the hub (the largest steady load). Thrust bending force bends blades forward as the aircraft is pulled along. Torque (air-resistance) bending force bends blades opposite the direction of rotation.
Two twisting moments fight over pitch: the centrifugal twisting moment (CTM) comes from the blade's mass trying to align with the plane of rotation and tends to rotate the blade toward low (fine) pitch - it is by far the stronger; the aerodynamic twisting moment (ATM) arises because the airfoil's center of pressure is forward of the pitch-change axis and tends to rotate the blade toward high (coarse) pitch .
Designers exploit these: CTM is often used to help drive blades to low pitch, and counterweights plus ATM (and oil) drive them to high pitch or feather.
Feathering turns the blades to about 90 degrees to the plane of rotation so a dead engine's propeller stops windmilling and presents minimum drag; feathering systems typically use a spring and counterweights to feather on loss of governor oil pressure, with an unfeathering accumulator or oil to recover. Reverse/beta moves the blades to a negative angle to produce reverse thrust for ground deceleration; beta and reverse must be rigged with low-pitch stops and locks because unintended movement below the flight-idle stop in flight could be catastrophic.
Propeller inspection is fundamentally fatigue prevention . A small nick, gouge, crack, corrosion pit, or erosion is a stress riser where a fatigue crack can start under the high cyclic loads a blade sees. Filing/blending of metal blades must stay within approved dimensional limits because removing material changes strength and balance; composite blades add delamination, erosion, moisture intrusion, lightning, and bond-failure concerns, and wood blades add moisture and glue-joint concerns.
Blade track (tip path within tolerance) and dynamic balance are checked, and any propeller strike is an airworthiness event requiring engine teardown/inspection per approved data.
Governor troubleshooting logic: if RPM rises above the selected value, the blades are not increasing pitch enough - suspect governor fault, low oil pressure to the hub, internal leakage, control rigging, blade friction, or an engine power change. If RPM is low or sluggish, blades may be too coarse or not returning fine, or the engine may not be making power. Compare manifold pressure/torque, RPM, oil pressure, and control position before condemning the propeller - a good engine can overspeed if the prop fails to coarsen, and a good prop turns slowly if the engine cannot make torque.
Two final inspection facts are commonly tested. Blade track is measured by rotating the propeller by hand and comparing each tip's path against a fixed reference; tips out of track beyond the allowed difference (often a fraction of an inch) indicate a bent blade or a loose hub and cause vibration. Dynamic balance is checked with an analyzer that reads vibration amplitude and phase, then adds small weights to the spinner bulkhead to reduce it.
A propeller strike - any contact with the ground or an object while turning - requires a sudden-stoppage / propeller-strike inspection of the engine per the manufacturer's data, because the shock can crack the crankshaft or gear train even if the blades look intact.