Study guide
8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
FAA A&P Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: Eligibility, FTN, Authorization, Three-Test Path, and Retakes
1.1 Certificate Ratings and the Three-Test Roadmap 1.2 Baseline Eligibility and the Experience Path 1.3 AMTS and Military Eligibility Pathways 1.4 FTN, IACRA, and the Authorization File 1.5 Knowledge-Test Logistics and Scoring 1.6 AKTRs, Retakes, and the DME Transition
2 ACS Map, Testing Matrix, Embedded Images, Supplements, and Study Workflow
2.1 Testing Matrix Facts for AMG, AMA, and AMP 2.2 ACS Map and Subject-Area Boundaries 2.3 AKTR ACS-Code Diagnostics 2.4 Testing Supplement and Embedded Images 2.5 Three-Test Study Workflow 2.6 Final Review and Test-Day Source Control
3 General I: Electricity, Drawings, Weight and Balance, Math, and Physics
3.1 Electricity and Electronics Foundations 3.2 AC/DC Measurement and Schematic Troubleshooting 3.3 Aircraft Drawings, Blueprints, and Schematics 3.4 Weight and Balance Equations and Records 3.5 Maintenance Math and Unit Discipline 3.6 Physics for Aviation: Forces, Fluids, and Flight
4 General II: Lines, Materials, Servicing, Corrosion, Records, Inspection, and Human Factors
4.1 Fluid Lines, Fittings, and Installation Risk 4.2 Materials, Hardware, and Process Control 4.3 Ground Operations, Servicing, and Ramp Safety 4.4 Cleaning, Corrosion Control, and Finishing 4.5 Regulations, Forms, Records, and Publications 4.6 Inspection Concepts, Human Factors, and Maintenance Judgment
5 Airframe I: Structures, Flight Controls, and Airframe Inspection
5.1 Metallic Structure Inspection and Damage Patterns 5.2 Sheet-Metal Repairs, Fasteners, and Riveting Judgment 5.3 Non-Metallic Structures: Composites, Wood, Fabric, and Plastics 5.4 Flight Control Systems, Rigging, and Travel 5.5 Control Surface Balance, Flutter, and Freeplay 5.6 Airframe Inspection, Records, ADs, and Corrosion Decisions
6 Airframe II: Landing Gear, Hydraulics, Pneumatics, Environmental, Instruments, and Comms
6.1 Landing Gear, Wheels, Tires, and Brakes 6.2 Retraction, Steering, Anti-Skid, and Warning Systems 6.3 Hydraulic Systems: Components, Fluids, and Troubleshooting 6.4 Pneumatic, Vacuum, and Bleed-Air Systems 6.5 Environmental Systems: Pressurization, Heating, Cooling, and Oxygen 6.6 Instrument Systems: Pitot-Static, Gyros, and Displays 6.7 Communication, Navigation, Antennas, and Avionics Inspection
7 Airframe III: Fuel, Electrical, Ice/Rain, Fire, Rotorcraft, and Water/Waste Systems
7.1 Airframe Fuel System Boundaries and Safe Servicing 7.2 Airframe Electrical Power, Wiring, and Protection 7.3 Ice and Rain Control System Inspection and Limits 7.4 Airframe Fire Protection Detection, Extinguishing, and Squib Safety 7.5 Rotorcraft Fundamentals, Controls, Drives, and Vibration 7.6 Water and Waste Systems Service Boundaries and Contamination Control
8 Powerplant I: Reciprocating, Turbine Engine Theory, and Engine Inspection
8.1 Reciprocating Engine Cycles, Components, and Operating Boundaries 8.2 Horizontally Opposed and Radial Engine Components 8.3 Reciprocating Engine Performance, Ground Operation, and Preservation 8.4 Turbine Engine Airflow, Sections, and Performance 8.5 Turbine Engine Maintenance, FOD, Bleed Air, and Post-Installation Checks 8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
9 Powerplant II: Instruments, Fire, Electrical, Lubrication, Ignition, and Starting
9.1 Engine Instrument Scan and Trend Logic 9.2 Pressure, Temperature, and Flow Indications 9.3 Engine Fire Protection, Detection, and Extinguishing 9.4 Engine Electrical Generation and Protection 9.5 Lubrication System Flow, Pressure, and Contamination 9.6 Ignition and Starting Troubleshooting
10 Powerplant III: Fuel Metering, Induction, Cooling, Turbine Air, Exhaust, Reversers, and Propellers
10.1 Engine Fuel System Flow, Contamination, and Vapor 10.2 Carburetors, Fuel Injection, and Metering Logic 10.3 Reciprocating Induction, Turbocharging, and Cooling 10.4 Turbine Air Systems, Bleed Air, and Anti-Ice 10.5 Exhaust Systems, Thrust Reversers, and Temperature Patterns 10.6 Propeller Systems, Governors, and Inspection
11 Oral/Practical Bridge: AKTR ACS Codes, DME Expectations, and Maintenance Judgment
11.1 Turn AKTR ACS Codes Into an Oral and Practical Remediation Plan 11.2 What the DME Oral Exam Is Really Testing 11.3 Practical Projects, Tools, Equipment, and Safety Discipline 11.4 Risk Management and Human Factors in the DME Environment 11.5 Documentation, Maintenance Records, and Data Discipline 11.6 Return-to-Service Judgment and Final DME Readiness
12 Final Review: Test Day Strategy, Three-Test Schedule, and Next Steps
12.1 Build the Final Study Calendar Around AMG, AMA, and AMP 12.2 PSI Test-Day Checklist Without Guesswork 12.3 Pacing for the 60-Question and 100-Question Knowledge Tests 12.4 Formula, Supplement, and Embedded-Image Final Review 12.5 Retake Decision Tree After a Failed or Weak Knowledge Test 12.6 DME Scheduling and Post-Pass Next Steps
8.6 Engine Inspection, Records, Compression, Borescope, and Airworthiness
Key Takeaways Explain This Topic AI
A differential compression test applies a regulated 80 psi to a cylinder at TDC on the compression stroke and reads the pressure the cylinder holds; the reading is judged against the minimum the engine manufacturer specifies.
Air escaping at the exhaust indicates an exhaust valve leak, at the carburetor/induction an intake valve leak, and at the crankcase breather worn rings or cylinder walls.
TBO (time between overhaul) is a manufacturer recommendation; under Part 91 it is advisory, while Part 135/121 operators must comply with their approved program.
Airworthiness joins physical condition with records: AD compliance, life-limited parts, required inspections, approved data, and event-driven special inspections.
Last updated: October 2026
The Differential Compression Test
The differential compression test is the standard cylinder-sealing check on reciprocating engines. The piston for the cylinder being tested is set at top dead center on the compression stroke , and a two-gauge tester applies shop air through a calibrated orifice so that a regulated 80 psi is supplied to the cylinder. The cylinder pressure gauge then shows how much of that pressure the cylinder holds, and the reading is judged against the minimum specified for the engine being tested in the manufacturer's procedure, rather than one fixed number for every engine.
Where the leaking air escapes localizes the fault:
- Air heard at Likely cause
- Exhaust pipe Leaking/burned exhaust valve
- Carburetor or induction intake Leaking intake valve
- Crankcase breather or oil filler Worn or stuck rings, scored cylinder walls
- Adjacent cylinder Head gasket or cracked head/block
Test a warm engine when the procedure calls for it, control the propeller throughout (the prop will try to rotate under 80 psi), and never condemn a cylinder on one number — staking the valves and retesting, plus borescope evidence, give the real picture.
Borescope, Records, and TBO
The borescope inspection provides direct visual evidence a compression test cannot: cylinder-wall scoring, burned or "tuliped" valves, detonation signatures, cracks, corrosion, deposits, and FOD. It complements compression data — a marginal compression number with clean valves and good walls reads differently than the same number with a burned valve. A borescope image, however, never overrides an approved-data rejection criterion: if the data requires removal for a given finding, the image supports that call.
Time between overhaul (TBO) is the manufacturer's recommended operating time before overhaul — typically 1,200 to 2,400 hours for piston engines and 3,500 hours or more for turbines (with a hot-section inspection at mid-life). TBO is a recommendation, not a regulatory limit, for Part 91 private operation ; Part 135 and 121 operators must comply with their approved maintenance programs. "On-condition" maintenance can extend service when condition monitoring supports it.
Overhaul scope varies: a top overhaul addresses the cylinders (pistons, rings, valves) without splitting the case, while a major overhaul disassembles the entire engine, inspects/replaces parts to new or service limits , and re-establishes baseline time.
Records and Airworthiness Decisions
The ACS lists engine inspection under 14 CFR part 43 and part 91 , covering life-limited parts, special inspections, approved data, service information, airworthiness directives (ADs) , type certificate data sheets (TCDS), and maintenance records. A clean engine with missing required records can still fail the airworthiness decision. A powerplant records review confirms engine identity, total time/cycles, time since overhaul, life-limited-part status, AD compliance, required-inspection status, and proper entries.
Special inspections are event-driven : a propeller strike or sudden stoppage, overspeed, overtemperature, lightning strike, hard landing, or ingestion event requires the applicable event-specific instructions before the engine is serviceable — regardless of how it sounds. Engine mounts and hardware are part of the boundary because they carry loads into the airframe; cracked mounts, deteriorated isolators, elongated holes, missing safetying, or wrong hardware can make a healthy engine unsafe.
A complete inspection joins condition, records, and procedure into one return-to-service judgment.
Inspection Authority, Approved Data, and the Maintenance Record Entry
Under 14 CFR part 65 , the holder of a mechanic certificate with the appropriate rating may approve a powerplant for return to service after maintenance, but a 100-hour or annual inspection has a higher bar: for an individual mechanic the annual must be signed by an Inspection Authorization (IA) holder, while a 100-hour inspection may be returned to service by an appropriately rated certificated mechanic.
Both inspections use the scope and detail of 14 CFR part 43, Appendix D , and the engine portion specifically calls for examining the engine and nacelle for cracks and security; studs and nuts for improper torque and obvious defects; the internal engine condition via the cylinder compression check (and the reason given for poor compression); and the engine mount for cracks and looseness.
It also covers flexible vibration dampeners; engine controls for defects, improper travel, and improper safetying; lines, hoses, and clamps for leaks, condition, and looseness; the exhaust stacks for cracks, defects, and improper attachment; and accessories for apparent defects in security of mounting.
The airworthiness decision is anchored in approved or acceptable data . Approved data includes the type certificate data sheet (TCDS) , FAA-approved sections of manufacturer manuals, airworthiness directives (ADs) , Supplemental Type Certificates, and Form 337 field approvals; manufacturer service bulletins and service letters are not required unless an AD refers to them or the authorized inspection program requires them, and only FAA-approved service bulletins count as approved data.
Life-limited parts (certain crankshafts, turbine disks, blades) must be retired at their published limit and cannot be "inspected past" it. The mechanic must verify AD compliance — recurring ADs in particular reset the clock and must be re-accomplished at their interval.
Use 14 CFR 43.9 for ordinary maintenance entries and 14 CFR 43.11 for required inspection entries. The entry states a description of the work (or reference to acceptable data), the date completed, and the signature, certificate number, and kind of certificate of the person approving the return to service. For inspections it also states the aircraft total time in service and whether it was found airworthy. An accurate, traceable record is itself part of airworthiness — an engine in perfect mechanical condition is not legally airworthy if the required entry, AD compliance, or life-limited-part tracking is missing.
This is why every chapter of powerplant study ends at the same place: condition plus records plus approved data equals one defensible return-to-service judgment.