Study guide

3.1 Bridge-to-Bridge Operations & VTS

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

3.1 Bridge-to-Bridge Operations & VTS

Key Takeaways Explain This Topic AI

A bridge-to-bridge station is a VHF radio on the navigational bridge or main control station used only for navigational communications in the 156–162 MHz band

U.S. Coast Guard Vessel Traffic Service (VTS) manages designated waterways to prevent collisions, groundings, and environmental harm

The required bridge-to-bridge watch in most continental U.S. areas is VHF-FM Channel 13 (156.650 MHz)

Normal bridge-to-bridge power is limited to 1 watt; higher power is allowed for distress, rounding bends/blind spots, emergencies, or when a called vessel fails to respond

On Channel 13, a ship station may identify by the vessel’s name instead of the call sign; Channel 16 remains the primary distress, safety, and calling watch for most vessels

Last updated: August 2026

3.1 Bridge-to-Bridge Operations & VTS

Quick Answer: A bridge-to-bridge station is VHF gear on the ship’s navigational bridge (or main control station) used only for navigational communications . In most U.S. waters the bridge-to-bridge watch is Channel 13 at 1 watt normal power. The Coast Guard’s Vessel Traffic Service (VTS) manages designated waterways to prevent collisions, groundings, and environmental harm. Keep navigation traffic short on Ch-13; keep the distress/safety/calling watch on Channel 16 (unless a specific VTS/GMDSS watch arrangement applies).

Element 1 Subelement B tests how commercial operators handle navigational voice procedures as well as distress and routine calling. Bridge-to-bridge work sits at the center of everyday ship safety: two bridges talking so vessels meet, overtake, and transit locks or bridges without a collision.

What Is a Bridge-to-Bridge Station?

Under Part 80 definitions, a bridge-to-bridge station is:

  • Located on the navigational bridge or main control station of the ship
  • Operating in the 156–162 MHz VHF maritime band
  • Used only for navigational communications

It is not an internal ship phone link between the wheelhouse and the radio room. It is not a portable “spare” station license for hopping vessels. It is not a general ship-to-shore business radio. If the message is about company cargo, crew payroll, or personal phone calls, it does not belong on bridge-to-bridge channels.

Primary purpose

The primary purpose of bridge-to-bridge communications is navigational communications —for example:

  • Meeting and overtaking arrangements (“one whistle,” port-to-port, etc.)
  • Intentions in narrow channels, bends, and restricted visibility
  • Communications with lock masters and drawbridge tenders
  • Short navigational coordination with nearby vessels

Messages must stay short . Congested waterways depend on everyone hearing the next meeting arrangement, not long chit-chat.

Channel 13: The Bridge-to-Bridge Watch

  • Item Exam fact
  • Channel VHF-FM Channel 13 (156.650 MHz) in most areas of the continental United States
  • Role Required bridge-to-bridge navigational watch / intership navigation safety
  • Normal power Not more than 1 watt

Ship max (when permitted) Up to 25 watts ship / 10 watts coast on the navigational pair under Part 80 footnotes—only when the situation justifies higher power

Related channel Channel 67 also serves navigational/commercial intership roles in some contexts; same low-power discipline applies where rules require 1 W

Identification On authorized VHF bridge-to-bridge channels, a ship may identify by the name of the ship in lieu of call sign

Exam anchor: “Which channel is utilized for the required bridge-to-bridge watch?” → VHF-FM on Ch-13 in most areas of the continental United States —not Ch-16, not Ch-70 DSC, and not “whatever working channel the vessel prefers.”

Power rules you will be tested on

Normal bridge-to-bridge power is 1 watt . Higher power on Channel 13 is legal when:

  • Broadcasting a distress message , and/or
  • Rounding a bend in a river or traveling in a blind spot , and/or
  • During an emergency , and/or
  • Failure of the vessel being called to respond

Pool wording combines several of these ideas:

“When may a bridge-to-bridge transmission be more than 1 watt?” → When broadcasting a distress message and rounding a bend / blind spot

“When is it legal to transmit high power on Channel 13?” → All of these (failure to respond, blind situation, emergency)

Operator habit: default the radio to low power (1 W) on Ch-13. Raise power only when safety requires it, then return to 1 W.

Vessel Traffic Service (VTS)

Vessel Traffic Service (VTS) is the U.S. Coast Guard traffic-management service in certain designated water areas. Its purpose is to prevent:

  • Ship collisions
  • Groundings
  • Environmental harm (oil spills, hazardous cargo incidents, channel blockages)

VTS areas use designated VHF working channels (often port-operations or VTS-specific channels such as Ch-14 in some ports). Operators in a VTS area must:

  • Monitor the assigned VTS channel(s) as required
  • Follow Coast Guard / VTS traffic instructions
  • Keep transmissions professional, short, and navigationally relevant
  • How VTS relates to Channel 16 watches

Element 1 also tests watchkeeping interplay:

Outside special arrangements, compulsory vessels maintain a continuous radiotelephone watch on Channel 16 (and often 2182 kHz for MF-fitted non-GMDSS ships outside harbor).

When a vessel is in a VTS system , is subject to the Bridge-to-Bridge Act , and is operating under the applicable A1/VTS rules, a Ch-16 watch may not be required if the vessel monitors both Channel 13 and the VTS channel —the pool’s “all of the above” style item treats several Ch-16 watch statements as true together.

Practical takeaway for GROL candidates: do not treat Ch-13 and Ch-16 as interchangeable. Ch-13 = navigation / bridge-to-bridge. Ch-16 = distress, safety, and calling. VTS adds a third layer of local traffic control. Many bridges run dual watch or multiple receivers so navigation and distress watches are continuous.

Identification on Bridge-to-Bridge Channels

A ship station using VHF bridge-to-bridge Channel 13 may be identified by the name of the ship in lieu of call sign . That does not mean identification is optional. It means the familiar voice format—“Motor Vessel Example , one whistle, meeting you green-to-green”—is legally acceptable on the navigational channel. On other maritime channels, normal call-sign identification rules still apply (beginning and end of transmissions, and at required intervals).

Operator Discipline on Navigational Channels

  • Do Don’t
  • Keep messages short and about navigation Use Ch-13 for long routine business or social chat
  • Default to 1 W Leave the radio on 25 W “just in case”
  • Monitor Ch-13 (and VTS channel when required) Assume Ch-16 alone covers bridge-to-bridge duties

Raise power for distress, blind spots, emergencies, non-response Ignore a non-responding vessel instead of increasing power when safety requires contact

Coordinate with Ch-16 distress/safety watchkeeping Jam Ch-16 with navigational meeting talk that belongs on Ch-13

Bridge-to-bridge radio is collision-avoidance infrastructure. Treat it like a short-range safety circuit shared by every ship in the fairway—not like a private bridge telephone.

  • Exam Memory Map
  • Definition → VHF on bridge/main control, navigational only
  • Purpose → Navigational communications
  • Watch channel (most CONUS) → Ch-13
  • Power → 1 W normal ; higher for distress/bend/blind/emergency/non-response
  • VTS → USCG service to prevent collisions, groundings, environmental harm
  • ID → Ship name allowed in lieu of call sign on bridge-to-bridge VHF
  • Relationship → Ch-13 navigation + Ch-16 distress/safety (+ VTS channel in VTS areas)