Study guide

4.6 Required Equipment Tests & On-Air Test Procedure

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

4.6 Required Equipment Tests & On-Air Test Procedure

Key Takeaways Explain This Topic AI

Test a radiotelephone installation by transmitting the station's call sign followed by the word test on the frequency being used

Testing on 2182 kHz or Channel 16 must not continue for more than 10 seconds in any 5-minute period

A compulsory VHF-DSC installation under GMDSS must be tested at least daily while at sea

The MF/HF NBDP system is tested by initiating an ARQ call to a coast station and awaiting the automatic exchange of answerbacks

  • An Inmarsat-C terminal is tested by composing and sending a brief message to your own terminal
  • Last updated: August 2026

4.6 Required Equipment Tests & On-Air Test Procedure

Quick Answer: Test by transmitting your call sign followed by the word "test" on the frequency in use. On 2182 kHz or Ch-16 , testing must not exceed 10 seconds in any 5-minute period . A compulsory VHF-DSC installation is tested daily at sea. Test NBDP with an ARQ call to a coast station and wait for the answerback exchange . Test Inmarsat-C by sending a brief message to your own terminal . You may test any time except during silent periods .

Official sub-topic 1-C-17 (Equipment Tests) is the operational partner of the logkeeping rules in section 2.4—the tests are what you log. It is also the sub-topic candidates most often lose a point on, because four different systems each have their own test method and the pool asks about them individually.

The on-air voice test procedure

What is the proper procedure for testing a radiotelephone installation?

Transmit the station's call sign, followed by the word "test", on the frequency being used for the test.

Three deliberate components:

  • Component Why it is there
  • Call sign Every transmission must identify its source—an unidentified carrier is a violation, not a test

The word "test" Tells every listening station this is not real traffic, so nobody starts a response or logs it as a call

On the frequency being used You test the frequency you intend to work, because the antenna and tuner behave differently on each

Note what is not in the procedure: counting "one two three four five," whistling into the microphone, keying an unmodulated carrier, or asking for a "radio check" from a coast station as a routine matter. Those are habits, not the rule.

The 10-second limit

When testing is conducted on 2182 kHz or Ch-16, testing should not continue for more than 10 seconds in any 5-minute period.

Learn both numbers together— 10 seconds in any 5-minute window. These are the shared distress and calling frequencies, and a station sitting on them for even half a minute can mask a genuine MAYDAY. The rule is deliberately tight to make routine testing on a distress frequency almost pointless, which is the intended nudge toward testing on a working frequency instead.

Pool distractors swap the numbers freely: "10 seconds in any minute," "30 seconds in any 5-minute period," "1 minute in any 10-minute period." 10 in 5 is the pair.

When may you test at all?

At any time (except during silent periods) as necessary to assure proper operation.

Two ideas in that answer. First, testing is routine and expected —you do not need permission or a scheduled window, because the whole point of a test is to confirm the gear works before you need it. Second, silent periods are excluded. On 2182 kHz the traditional silent periods run for three minutes from each hour and each half hour, when stations listen for weak distress traffic. Testing through a silent period defeats it.

Contrast this with genuine urgency or distress traffic (section 3.4), which is never blocked by a silent period. The restriction applies to testing, not to real emergencies.

System-by-system test methods

This is the part worth drilling as a table, because each system has exactly one keyed answer:

  • System Test method Interval
  • Radiotelephone (voice) Call sign + the word "test" on the frequency in use As needed, except silent periods
  • Compulsory VHF-DSC Internal self-test Daily at sea

MF/HF NBDP Initiate an ARQ call to a coast station and wait for the automatic exchange of answerbacks Per carriage rules

  • Inmarsat-C Compose and send a brief message to your own terminal Per carriage rules
  • EPIRB Self-test Monthly (logged monthly — section 2.4)
  • Why each method is the right one

VHF-DSC — daily. Under GMDSS a compulsory VHF-DSC installation must be tested at least daily while at sea . Daily because DSC is the primary alerting path on a coastal voyage and a silent failure would be invisible until the moment it mattered. Do not confuse this with the monthly EPIRB interval; the pool pairs them precisely to catch that swap.

NBDP — ARQ answerback. Narrow-Band Direct Printing (radiotelex) is tested by placing an ARQ (Automatic Repeat reQuest) call to a coast station and confirming the automatic exchange of answerbacks . The answerback exchange proves the whole chain end to end: your transmitter, the link, the coast station, and your receiver and printer. A one-way "send some text and see" proves far less, which is why the specific answer names ARQ and answerbacks.

Inmarsat-C — message to yourself. The self-addressed message is elegant for the same reason: it exercises transmit, the satellite, the land earth station, the routing, and receive, all without bothering anyone ashore or generating traffic someone must answer. Options suggesting you call the Inmarsat operator, send a test to a coast station, or trigger the distress button are wrong—and the last one is seriously wrong.

Never test with the distress function

It should not need saying, but the pool tests it obliquely in several places: you do not verify a DSC controller by pressing the distress button, and you do not verify an EPIRB by activating it. Both generate real alerts that pull SAR resources. Use the built-in self-test, and if a false alert does go out, cancel it immediately (section 5.2).