Study guide

4.5 MF/HF Frequency & Emission Selection

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

4.5 MF/HF Frequency & Emission Selection

Key Takeaways Explain This Topic AI

2182 kHz is the MF radiotelephony calling and distress frequency, and J3E single-sideband telephony is the required emission on it

A vessel calls another ship on 2182 kHz or Channel 16 unless it knows the called vessel keeps a simultaneous watch on another intership working frequency

Paired (duplex) frequencies are normally used with public coast stations; simplex frequencies serve intership working traffic

ITU channel numbering encodes the band and the channel: ITU Channel 1212 is the 12th channel in the 12 MHz band

MF/HF marine radiotelephony uses SSB, not AM - a set left in the wrong emission mode will be unintelligible to the receiving station

Last updated: August 2026

4.5 MF/HF Frequency & Emission Selection

Quick Answer: 2182 kHz is the MF radiotelephony calling and distress frequency and it uses J3E (single-sideband telephony). Call another ship on 2182 kHz or Ch-16 unless you know it watches another intership working frequency. Paired frequencies → public coast stations ; simplex → intership. ITU Channel 1212 = the 12th channel in the 12 MHz band .

Section 4.2 covered the controls on an MF/HF SSB set—clarifier, RF gain, tuner, mode switch. Official sub-topic 1-C-16 (MF-HF Frequency & Emission Selection) is about which frequency and which mode , and it rewards understanding one organising idea: the MF/HF marine band is split by who you are talking to .

2182 kHz and the emission that goes with it

What is the MF radiotelephony calling and distress frequency? 2182 kHz. This is the medium-frequency counterpart of VHF Channel 16, and the parallel runs deep:

  • Role VHF MF
  • Calling and distress Ch-16 (156.800 MHz) 2182 kHz
  • DSC alerting Ch-70 2187.5 kHz
  • Emission G3E (FM) J3E (SSB)

What emission must be used when operating on the MF distress and calling voice frequency? J3E — single-sideband telephony. Decode the designator: J = single-sideband, suppressed carrier; 3 = a single analogue channel; E = telephony. Marine MF/HF radiotelephony abandoned full-carrier AM decades ago because SSB puts all the transmitter's power into the intelligence instead of wasting most of it on a carrier and a redundant sideband.

Practically: an operator who leaves the mode switch on AM, or on the wrong sideband, will be unreadable. Marine SSB convention is upper sideband , and a set on LSB produces the familiar inverted, unintelligible "donald duck" audio.

The calling convention

On what frequency would a vessel normally call another ship station when using a radiotelephony emission?

On 2182 kHz or Ch-16, unless the station knows that the called vessel maintains a simultaneous watch on another intership working frequency.

Both halves of that answer are testable. The default is the calling frequency; the exception is knowledge—if you already know the other vessel is guarding a particular working frequency, calling there directly keeps the distress/calling frequency clear. Note the standard for the exception is knowing , not guessing.

This also explains why 2182 kHz and Ch-16 are kept clear: they are shared, congested, and carry distress traffic. Any working conversation belongs elsewhere.

Paired versus simplex — the organising idea

Frequency arrangement Also called Normally used with Why

Paired Duplex / two-frequency Public coast stations The coast station transmits on one frequency and receives on another, so both ends can talk at once and the station can handle telephone-network traffic

Simplex Single-frequency Intership working traffic Both vessels share one frequency and take turns; simpler, and no shore infrastructure required

The pool asks this from both directions. "For general communications purposes, paired frequencies are: normally used with public coast stations ." And the simplex question is keyed to a combined option, because simplex serves more than one purpose—intership work and, on some channels, semi-duplex arrangements.

The practical link: public correspondence (a call patched into the shore telephone network) needs paired frequencies, which is why VHF Ch-28 in section 4.4 is a duplex channel. Section 20.3's USA–INT control exists because some channels that are duplex in the international plan are used as simplex domestically.

ITU channel numbering

Which of the following defines high frequency "ITU Channel 1212"? The 12th channel in the 12 MHz band.

The scheme is positional, and once you see it the numbers decode themselves:

  • ITU channel Band Channel within band
  • 1212 12 MHz 12
  • 801 8 MHz 01
  • 1607 16 MHz 07
  • 421 4 MHz 21

Read the leading digit(s) as the band in MHz and the trailing two digits as the channel number within that band . Distractors typically offer "channel 1212 in the 12 MHz band" (redundant), "the 12th channel of the 1200 series," or a reversed reading such as "the 12 MHz channel in band 12."

The marine HF bands you will see numbered this way are roughly 4, 6, 8, 12, 16, 18/19, 22 and 25 MHz. Band choice is a propagation decision in practice—lower bands at night and for shorter distances, higher bands in daylight for long haul—though the current Element 3 pool does not test propagation directly.

Putting a working call together

Choose the band appropriate to distance and time of day.

Call on 2182 kHz (or Ch-16 on VHF) unless you know the vessel guards a working frequency.

Use J3E — upper sideband on marine HF.

Shift to a working frequency : simplex for intership, a paired channel for a public coast station.

Keep the calling frequency clear so distress traffic is not blocked.

Exam traps

2182 kHz emission → J3E , not A3E and not G3E. A3E belongs to aviation VHF (section 4.4).

Paired frequencies → public coast stations , not intership.

ITU 1212 → 12th channel in the 12 MHz band .

The calling exception requires knowing the other station guards another frequency.