Study guide

4.1 VHF Equipment Controls

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

4.1 VHF Equipment Controls

Key Takeaways Explain This Topic AI

The INT-USA control changes certain international duplex VHF assignments to simplex in U.S. waters for VTS and other purposes—not every channel and not weather-band selection

Channel 16 is distress, safety, and calling; Channel 13 is bridge-to-bridge in most CONUS areas; Channel 70 is DSC only; Channel 22A is the usual U.S. Coast Guard working channel after initial contact; Channel 06 is intership safety

Simplex uses one frequency so nearby vessels hear both sides; duplex uses separate ship/coast frequencies—distress, urgency, safety, and VTS traffic must be simplex so third parties can monitor the exchange

VHF ship transmitters must reduce to 1 watt; maximum shipboard F3E carrier power is 25 watts—use low power near shore and on navigational channels when rules require it

Set squelch to the minimum level that just quiets background noise; Dual Watch listens on a selected channel while periodically checking Channel 16; Scan steps through all or selected channels

Last updated: August 2026

4.1 VHF Controls & Channel System

Quick Answer: Know the INT-USA switch (certain international duplex channels become simplex in U.S. waters for VTS and related uses), the core channel map ( 16 distress/calling, 13 bridge-to-bridge most CONUS, 70 DSC only, 22A USCG working after call, 06 intership safety), simplex vs duplex , 25 W / 1 W power, and correct squelch , Dual Watch , and Scan settings. Weather channels are receive-only marine weather.

Element 1 Subelement C (Equipment Operations) tests whether you can operate a marine VHF set the way Part 80 and good bridge practice require—not just “pick a channel and talk.” This section covers controls (key topic 13) and channel selection (key topic 14).

INT-USA: why the same channel number is not always the same radio path

Marine VHF channel numbers are international, but frequency pairing is not identical everywhere. Many ship-to-shore public correspondence and some operational channels are duplex internationally: the ship transmits on one frequency and the coast station transmits on another. In U.S. waters, some of those same channel numbers are used as simplex for Vessel Traffic Service (VTS) and other domestic needs so every vessel on the channel hears the same frequency.

Purpose of the INT-USA control: to change certain International duplex channel assignments to simplex in the U.S. for VTS and other purposes .

  • Wrong idea Correct Element 1 idea
  • INT-USA changes all channels duplex ↔ simplex Only certain international duplex assignments
  • INT-USA selects NOAA weather Weather is a separate WX receive function

INT-USA “forces duplex so everyone hears orders” U.S. mode makes selected assignments simplex so vessels can hear VTS/orders on one frequency

Operator habit: when you enter U.S. waters (or leave them), confirm the radio’s USA / INT (or INT-USA ) mode matches the region. Wrong mode can put you on a frequency pair that the local VTS or coast station is not using for that channel number.

Simplex vs duplex—and why safety traffic is simplex

Mode How it works Who hears what

Simplex Ship and coast (or ship and ship) use the same frequency for transmit and receive Any third vessel monitoring that channel can hear both sides of the exchange

Duplex Ship TX on frequency A; coast TX on frequency B A third party on only one of the pair may hear only half the conversation

Why all VHF distress, urgency, and safety communications (and VTS traffic calls) must be in simplex: so vessels not directly in the exchange can still hear both sides. That shared situational awareness is collision avoidance and SAR coordination, not a technical nicety.

Routine ship-to-ship working channels and bridge-to-bridge navigation are also simplex. Public correspondence (marine telephone) channels are classically duplex ship/coast pairs—use them for phone patch traffic, not for MAYDAY coordination.

Core channel map (memorize cold)

Channel Role Operator rule

16 (156.800 MHz) International distress, safety, and calling Compulsory VHF-FM vessels monitor when at sea (subject to limited VTS/bridge-to-bridge watch exceptions taught in watchkeeping)

13 (156.650 MHz) Bridge-to-bridge navigational watch in most continental U.S. areas Navigational traffic; normal power often 1 W

70 (156.525 MHz) Digital Selective Calling only No voice on Ch-70

22A Typical U.S. Coast Guard working / liaison channel after contact Call CG on 16 (or via DSC), then shift to 22A when directed

06 Intership safety Safety-related ship-to-ship voice, not a substitute for Ch-16 distress watch

08 (example) Routine commercial intership working After contact on 16, move routine traffic here or another authorized working channel

28 (example) Public correspondence (marine operator / shore telephone) Shore-telephone style traffic, not distress calling

Channel 16

What channel must VHF-FM-equipped vessels monitor at sea? Channel 16.

Use it for distress, urgency, safety, and initial calling —then move to a working channel so 16 stays clear.

Do not park long business conversations on 16.

Channel 13

Required bridge-to-bridge watch in most areas of the continental United States: VHF-FM Channel 13 .

  • Not Ch-16, not Ch-70 DSC, and not “whatever working channel the vessel prefers.”
  • Channel 70

Used only for DSC (distress alerts, safety-related digital calls, individual/group DSC calling).

Voice on 70 is always wrong on Element 1.

Channel 22A and Channel 06

After establishing contact with the U.S. Coast Guard on Ch-16 (or via DSC), expect to shift to a USCG working channel —commonly 22A in U.S. practice—for the working exchange and safety information.

Ch-06 is the classic intership safety channel for safety-related ship-to-ship voice when that role is required.

Weather channels

Marine VHF sets include NOAA weather receive channels (WX). They are for continuous weather broadcasts— not ship transmit channels and not what the INT-USA control is for.

Power: 25 W high / 1 W low

VHF ship station transmitters must be capable of reducing carrier power to 1 watt. Shipboard F3E (FM voice) maximum carrier power is 25 watts .

  • Setting Typical use
  • High (up to 25 W) Open water, weak stations, longer VHF range when needed
  • Low (1 W) Harbor, near other vessels, bridge-to-bridge when required, any time low power is enough

Exam anchor: capability to reduce to 1 W is mandatory for ship VHF (with narrow automation/public-correspondence exceptions you will not invent). Default low when close; raise power only when range or non-response requires it.

  • Volume, squelch, Dual Watch, and Scan
  • Volume

Sets loudspeaker/handset audio level. Volume does not change transmitter power or receiver sensitivity to weak RF signals the way RF gain might on an HF set—on VHF it is primarily how loud a opened squelch sounds.

Squelch (manual)

Correct manual squelch setting: adjust to the minimum level necessary to barely suppress background noise .

Too open → constant hiss, operator fatigue, missed weak calls buried in noise fatigue.

Too tight → weak but valid stations (including distant distress or VTS) never open the audio.

  • Do not leave squelch at maximum “to stay quiet.”
  • Dual Watch (DW)

Dual Watch lets you listen on any selected working channel while the radio periodically monitors Channel 16 . It is not “monitor Ch-70 with Ch-16,” not a four-channel scanner, and not a full-band sweep by itself.

Scan

Scan sequentially steps through all or selected channels, stopping when the squelch opens. Use a scan list that includes required watches without drowning the operator in irrelevant traffic.

Aircraft distress frequency (related channel-selection item)

Element 1 also tests the aviation SAR voice frequency used in maritime/SAR context: 121.500 MHz with A3E (AM voice)—not marine FM Ch-16 emission, and not “F3E on 121.5.” Survival craft and SAR coordination may involve that air-band distress frequency; know the frequency + emission pair.

Operator discipline checklist

Mode: USA vs INT set for the waters you are in.

Watch: Ch-16 (and Ch-13 / VTS channels as required); Ch-70 for DSC watch on DSC-equipped vessels.

Power: 1 W when required or sufficient; ≤ 25 W ship F3E maximum.

Squelch: just quiet—no tighter.

Traffic flow: call on 16 → work on 13 / 22A / 06 / 08 / other authorized channel as role requires.

Never voice on 70.

Master the panel and the channel map, and most Subelement C VHF questions become recognition rather than guesswork.