Study guide

5.4 Search and Rescue Transponders (SARTs)

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

5.4 Search and Rescue Transponders (SARTs)

Key Takeaways Explain This Topic AI

A SART operates in the 9 GHz band and responds only when interrogated by a 9 GHz X-band radar signal

A SART response appears on the radar display as a series of 12 equally spaced dots running outward from the SART position

The SART's audible tone alarm tells survivors that assistance may be nearby, because it sounds when a radar is interrogating it

A SART transmits nothing on its own - it must be switched on and then interrogated before it responds

SART effective range is maximised by holding or mounting the unit as high as possible, since 9 GHz propagation is essentially line of sight

Last updated: August 2026

5.4 Search and Rescue Transponders (SARTs)

Quick Answer: A SART works in the 9 GHz band and is received by a vessel's X-band navigational radar . Switched on, it responds only when interrogated by a 9 GHz radar signal . Its reply paints 12 equally spaced dots on the radar display. Its audible tone alarm tells survivors assistance may be nearby . Range is maximised by holding it as high as possible .

Official sub-topic 1-D-22 (SARTs) is a six-question sub-topic with an unusually consistent answer set. Every item turns on the same physics— 9 GHz, transponder, line of sight —so understanding the device once secures all six.

What a SART actually is

A Search and Rescue Transponder is not a beacon. An EPIRB (section 5.2) transmits on its own initiative and keeps transmitting. A SART is a transponder : it stays quiet until something interrogates it, then answers.

  • Property EPIRB SART
  • Frequency 406 MHz satellite alert (+121.5 MHz homing) 9 GHz (X-band)
  • Behaviour Transmits on activation Responds to interrogation
  • Detected by COSPAS-SARSAT satellites A ship's or aircraft's X-band navigational radar
  • Purpose Alerting — tells the world you are in trouble Locating — guides a nearby rescuer to you

That split is the design logic of GMDSS: alerting and locating are different jobs done by different devices.

The 9 GHz choice

In which frequency band does a search and rescue transponder operate? 9 GHz. And: "This is a 9 GHz transponder capable of being received by a vessel's X-band navigational RADAR system."

Why 9 GHz? Because that is where X-band marine navigational radar already lives. Practically every vessel and SAR aircraft carries an X-band radar; a SART needs no new receiver anywhere, only an existing radar to interrogate it. Distractor bands—3 GHz S-band, 406 MHz, 2182 kHz—are all wrong, and 3 GHz is the sharpest trap because S-band radar is also common on larger ships. A SART does not respond to S-band radar.

The twelve dots

How should the signal from a Search and Rescue Radar Transponder appear on a RADAR display? A series of 12 equally spaced dots.

The mechanism is worth knowing because it makes the number memorable. When interrogated, the SART sweeps rapidly across the radar band twelve times. Each sweep passes through the radar's receiver passband once, painting one blip. Because the sweeps are evenly timed, the blips land at even range intervals, radiating outward from the SART's own position along its bearing line.

Two display behaviours follow, and both are useful in practice:

At longer range , the twelve dots appear as a clean line of separate blips leading away from the SART.

As you close in , the dots widen into arcs and eventually into concentric circles—a strong visual cue that you are nearly on top of it.

Distractors offering "a single solid range ring," "twenty continuous dashes," or "a figure-eight pattern" are all wrong. Twelve equally spaced dots.

The audible alarm

What is the purpose of the SART's audible tone alarm? It informs survivors that assistance may be nearby.

The alarm does not call for help and it does not signal the rescuer. It sounds when the SART is being interrogated , which means a radar is illuminating it, which means a vessel or aircraft with radar is within range. For people in a liferaft in poor visibility, that is enormous—it converts an invisible electronic process into a morale-sustaining, actionable signal: help is close, get your visual signals ready.

When does it transmit?

At what point does a SART begin transmitting? If it has been placed in the "on" position, it will respond when it has been interrogated by a 9-GHz RADAR signal.

Both conditions are required, and the answer states them in order:

  • It must be switched on — a SART in standby does nothing
  • It must be interrogated by a 9 GHz radar

This conserves battery. A SART left responding continuously would flatten itself long before a search unit arrived. Options claiming it "transmits continuously once activated," "begins on immersion in water," or "transmits every 50 seconds" describe EPIRB-like behaviour, not a transponder.

Maximising range

How can a SART's effective range be maximised? The SART should be held as high as possible.

At 9 GHz, propagation is essentially line of sight , so the limiting factor is the radar horizon between the SART's antenna and the searching radar's antenna. Every metre of height buys usable range. In practice:

Mount the SART on its telescopic pole or lash it to the liferaft's highest point rather than leaving it on the floor

A SART held roughly a metre above the water is typically detected by a ship's radar at around 5 nautical miles, and by a search aircraft at low altitude much farther, because the aircraft supplies the height on its end

  • Nothing else the survivor can do—pointing, rotating, shielding—matters nearly as much as height
  • Exam trap summary
  • Item Answer Common wrong answer
  • Band 9 GHz 3 GHz S-band, 406 MHz
  • Display 12 equally spaced dots Solid ring, 20 dashes
  • Alarm purpose Tells survivors help may be near Alerts the rescue vessel
  • Transmit trigger On + interrogated by 9 GHz radar Continuous once activated
  • Range Hold as high as possible Point it at the horizon