Study guide

2.1 Equipment Requirements (Part 80)

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

2.1 Equipment Requirements (Part 80)

Key Takeaways Explain This Topic AI

Only transmitters certified by the FCC for Part 80 operations are authorized aboard U.S. vessels (unless a narrow exception applies).

Small passenger vessels operated within about 20 NM of land need VHF-DSC radiotelephone; vessels operating roughly 20–150 NM from land must also carry MF-HF SSB capability.

A DSC controller is the equipment programmed to initiate distress alerts and individual station calls.

Compulsory vessels need an MF transmitter of at least 60 watts PEP; shipboard F3E (FM voice) transmitters are limited to 25 watts carrier power.

Last updated: August 2026

2.1 Equipment Requirements (Part 80)

Quick Answer: Aboard U.S. vessels, use only FCC Part 80–certified maritime transmitters. Small passenger vessels need VHF-DSC near shore and MF-HF SSB farther out. DSC controllers start distress and individual calls. Compulsory MF gear must deliver at least 60 W PEP; shipboard FM (F3E) voice is capped at 25 W carrier.

Element 1 (Basic Radio Law and Operating Practice) opens with equipment authorization and carriage . These rules live mainly in 47 CFR Part 80 (Stations in the Maritime Services). You do not need to recite every section number on exam day, but you must know what is legal to install, what power levels are required or allowed, and which box actually starts a Digital Selective Calling (DSC) alert.

Part 80 certification is non-negotiable

What transmitting equipment is authorized for maritime stations after September 30, 1986? Unless specifically excepted, only transmitters certified by the FCC for Part 80 operations.

That single rule answers two common exam framings:

Requirement for marine transmitting apparatus aboard U.S. vessels — only Part 80–certified equipment is authorized.

Authorized transmitting equipment in the maritime services — again, FCC Part 80 certification (not Coast Guard “type acceptance,” not manufacturer self-certification alone, and not a general ITU claim without Part 80 certification).

Why certification matters

Part 80 certification means the Commission has found that the model meets maritime technical standards: channeling, emission masks, power control (including low-power reduction where required), DSC functions where applicable, and other Part 80 performance rules. Installing non-certified “land mobile” or amateur gear as a ship station transmitter is not a workaround.

Claim you may hear Exam-correct position

“Coast Guard type-accepted it, so it is fine” Coast Guard approval is not the Part 80 equipment authorization answer

“Manufacturer says it is marine grade” Marketing claims do not replace FCC Part 80 certification

“ITU specs are enough” ITU alignment may matter internationally, but U.S. stations need Part 80–certified transmitters

“Any VHF with marine channels is legal” Channel list alone is insufficient without Part 80 certification

Memory hook: Part 80 certificate on the radio — or it does not go on the U.S. vessel as a ship transmitter.

Small passenger vessel carriage by distance from land

Compulsory carriage for small passenger vessels scales with how far the vessel operates from the nearest land. Element 1 frames the mid-range requirement simply:

  • Operating distance from nearest land (exam framing) Minimum radio carriage concept
  • Within ~20 nautical miles VHF-DSC radiotelephone installation
  • Beyond ~20 NM, out through roughly 20–150 NM MF-HF SSB capability in addition to near-shore VHF needs

Farther / higher risk voyages Additional GMDSS-class redundancy and long-range systems (covered more fully in GMDSS elements)

What the exam wants you to recall

Close in (within about 20 NM): VHF with DSC is the foundation. VHF Channel 16 (156.8 MHz) remains the voice distress/safety/calling channel; Channel 70 is the VHF DSC channel.

Offshore in the “20 to 150 NM” band used on Element 1: add an MF-HF SSB transceiver (medium-frequency / high-frequency single-sideband). VHF line-of-sight alone is not enough for reliable distress and safety coverage at those distances.

Element 1 often asks: Small passenger vessels that sail 20 to 150 nautical miles from the nearest land must have what additional equipment? Correct idea: MF-HF SSB transceiver — not an aircraft 121.5 MHz radio as the Part 80 small-passenger answer, and not “Inmarsat only” as a substitute for that classic pool item.

Operational reason (why the rule exists)

VHF is excellent near shore where coast stations, Vessel Traffic Services, and other vessels share the same horizon. Beyond roughly 20 NM, MF/HF sky-wave and ground-wave paths extend distress, urgency, and safety reach. Carriage rules force that capability onto small passenger vessels that actually operate there.

DSC controller: the distress and individual-call initiator

Digital Selective Calling (DSC) is the automated digital calling layer used with VHF, MF, and HF maritime radios in the GMDSS environment.

What equipment is programmed to initiate transmission of distress alerts and calls to individual stations? The DSC controller .

Device Role Initiates distress/individual DSC calls?

  • DSC controller Formats and sends DSC messages (distress, urgency, safety, individual, group) Yes
  • NAVTEX receiver Receives maritime safety information broadcasts No
  • GPS/GNSS receiver Provides position to DSC/EPIRB systems No (position source only)
  • Scanning watch receiver Monitors frequencies No

Know the distinction: a GPS feed is critical for position-tagged distress alerts, but the controller is what is programmed to initiate the DSC transmission. NAVTEX is receive-side safety text, not the ship’s DSC caller.

Practical picture: the operator (or a dedicated distress button wired through the DSC controller) triggers a formatted alert containing the ship’s MMSI , nature of distress (if selected), and position when a navigation receiver is connected. The same controller can address individual stations by MMSI for routine or safety calls instead of open voice hailing.

Power rules you must memorize

Two power figures appear constantly in Element 1 equipment questions.

1) MF transmitter minimum for compulsory vessels — 60 watts PEP

Minimum transmitter power level required by the FCC for a medium-frequency transmitter aboard a compulsorily fitted vessel: at least 60 watts peak envelope power (PEP) .

This is a floor for the compulsory MF radiotelephone transmitter (associated with emissions such as H3E/J3E on distress and working MF frequencies, including 2182 kHz context in the rules).

Distractors often invent 25 W (the VHF carrier cap), 100 W “nice round numbers,” or vague “whatever power reaches the nearest coast station.” The exam answer is the 60 W PEP minimum.

2) Shipboard F3E (FM voice) maximum — 25 watts carrier

Shipboard transmitters using F3E emission (FM voice) may not exceed 25 watts carrier power .

F3E is the emission designator for frequency-modulated telephony used on marine VHF.

On ship stations in the 156–162 MHz marine VHF band, Part 80 caps power at 25 W , with reduction capability to 1 W or less on most equipment (important for close-quarters channels such as bridge-to-bridge practice covered later).

Do not confuse handheld portable limits (~5 W class) with the fixed ship station 25 W maximum carrier figure tested here.

  • Parameter Value Kind of limit
  • Compulsory MF transmitter ≥ 60 W PEP Minimum capability
  • Shipboard F3E / FM voice (VHF class) ≤ 25 W carrier Maximum authorized
  • Typical low-power setting (VHF) 1 W Required reducibility / good practice on many channels
  • Putting the equipment rules together

When an Element 1 stem mentions U.S. vessel , Part 80 , small passenger , DSC , MF , or F3E , run this checklist:

Is the transmitter Part 80–certified? If not, it is not authorized (except narrow, named exceptions you will not invent on the exam).

How far does the small passenger vessel operate? Inside ~20 NM → VHF-DSC core; out into the ~20–150 NM range → add MF-HF SSB .

What starts digital distress/individual calls? DSC controller , not NAVTEX or GPS alone.

Power: MF compulsory floor 60 W PEP ; shipboard FM voice ceiling 25 W carrier .

These four points cover the equipment half of Subelement A and feed directly into license, watch, and log rules in the next sections.