Study guide

2.3 Watchkeeping & Logkeeping Duties

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

2.3 Watchkeeping & Logkeeping Duties

Key Takeaways Explain This Topic AI

Compulsory radiotelephone stations maintain a continuous VHF Channel 16 (156.8 MHz) distress watch while underway, with a VTS/bridge-to-bridge exception when both the bridge-to-bridge frequency and VTS channel are monitored.

Compulsory cargo ships outside harbor (non-GMDSS / non-VTS context) keep continuous radiotelephone watch on 2182 kHz and Channel 16.

Mandatory DSC watches include VHF Channel 70, 2 MHz MF DSC, 8 MHz HF DSC, and one other HF DSC frequency.

Ship station logs are kept at the principal radiotelephone operating position; GMDSS logs stay at the GMDSS operating position; distress-related logs are retained three years.

Apply for ship radio station inspection to the Engineer-in-Charge of the FCC district office nearest the proposed inspection location.

Last updated: August 2026

2.3 Watchkeeping, Logkeeping & Inspections

Quick Answer: Keep a continuous Channel 16 watch on compulsory radiotelephone stations; cargo ships outside harbor also watch 2182 kHz (non-GMDSS context). DSC watches include Ch-70 , 2 MHz MF DSC , 8 MHz HF DSC , and one other HF DSC . VTS participants may drop Ch-16 if monitoring bridge-to-bridge and the VTS channel. Logs live at the principal operating position (GMDSS log at the GMDSS position ); distress entries keep 3 years . Inspection applications go to the Engineer-in-Charge of the nearest FCC district office.

Subelement A finishes with what you must listen to , what you must write down , and who inspects the installation . These rules protect the distress system: a brilliant transmitter is useless if no one is watching the distress channel or the log cannot prove what happened.

Compulsory radiotelephone watch — Channel 16 first

Radio watches for compulsory radiotelephone stations include a continuous VHF Channel 16 watch.

Channel 16 = 156.8 MHz , international distress, safety, and calling for VHF radiotelephony.

Each compulsory vessel , while underway , must maintain a watch for radiotelephone distress calls on 156.8 MHz whenever the station is not exchanging other communications.

All compulsory non-GMDSS vessels in the open sea must monitor Channel 16 at all times (exam wording).

Cargo ships outside harbor (classic Element 1 pair)

All compulsory equipped cargo ships (except those operating under GMDSS regulations or in a VTS ), while navigated outside of a harbor or port , shall keep a continuous radiotelephone watch on:

2182 kHz and Channel 16.

  • Frequency / channel Role
  • VHF Ch-16 (156.8 MHz) Near/mid-range voice distress, safety, calling
  • 2182 kHz (MF) Longer-range MF radiotelephone distress/safety/calling counterpart
  • Remember the pairing: outside harbor, non-GMDSS cargo → both MF distress voice and VHF Ch-16, not “pick one.”
  • Silent periods on 2182 kHz

When a 2182 kHz watch is required, a 3-minute silent period is observed twice each hour beginning at H+00 and H+30 UTC. Except for distress, urgency, or safety messages, stations must not transmit on 2182 kHz during those silence periods. Element 1 may ask the clock times: 00 and 30 past the hour—not 15/45 or 05/35.

VTS may relieve the Channel 16 watch

The Ch-16 watch is not required in specific cases, including:

Ship station operating only with handheld bridge-to-bridge VHF under the applicable Part 80 provision; or

Vessels subject to the Bridge-to-Bridge Act and participating in a Vessel Traffic Service (VTS) when watch is maintained on both :

  • the bridge-to-bridge frequency (commonly Channel 13 in many U.S. waters), and
  • a separately assigned VTS channel

Exam composite: Ch-16 is compulsory at sea until further notice unless the vessel is in a qualifying VTS arrangement; in an A1/VTS bridge-to-bridge situation, monitoring Ch-13 (bridge-to-bridge) and the VTS channel can replace the Ch-16 watch; Ch-16 remains compulsory in other sea areas as framed by the pool. If a stem says “all of the above” about those Ch-16 truths, that is often the keyed answer.

Mandatory DSC watchkeeping bands/channels

Mandatory DSC watchkeeping (exam list):

  • VHF Channel 70 (VHF DSC)
  • 2 MHz MF DSC
  • 8 MHz HF DSC
  • One other HF DSC frequency
  • Band / channel Purpose
  • VHF Ch-70 Digital selective calling on VHF (not voice)
  • 2 MHz MF DSC Medium-frequency DSC distress/safety watch
  • 8 MHz HF DSC Primary HF DSC watch frequency group on the exam list
  • 1 other HF DSC Additional HF DSC frequency as required

Distractors mix in Ch-16 (voice, not DSC), 6 MHz only, or omit the second HF DSC. Memorize the four-part set: 70 + 2 MHz + 8 MHz + one other HF .

  • Logkeeping — responsibility, location, retention
  • Who is responsible and who writes

Station licensee and the radio operator in charge of the station are responsible for proper maintenance of station logs.

Entries in a required service or maintenance log are made by the operator responsible for the station operation or maintenance (not “any RR holder,” and not automatically “the tech who turned the screwdriver” unless that person is the responsible operator).

Where logs live during a voyage

  • Log type Location while vessel is navigated
  • Ship station logs with required radiotelephone entries Principal radiotelephone operating position
  • GMDSS radio log GMDSS operating position
  • Radiotelegraph logs Principal radiotelegraph operating room

Do not park the working voyage log in the captain’s cabin safe or take it home in the operator’s sea bag. Inspectors and watchstanders need it at the operating position.

Corrections

No erasures or obliteration during the retention period.

The person who originated the entry strikes out the error, initials the correction, and dates it (electronic logs use strikethrough + dated electronic acknowledgment).

Retention periods

  • Content Retention
  • Ordinary station log entries (no distress/disaster) 2 years from date of entry
  • Entries relating to a distress situation or disaster 3 years from date of entry
  • Logs under FCC investigation notice Until FCC authorizes destruction in writing
  • Logs related to a claim/complaint Until satisfied or time-barred

Element 1 loves the distress retention figure: three years .

What goes in the log (high-yield)

Radiotelephone stations required to keep transmission logs include, as applicable:

  • Station identification, date and time (UTC as required)
  • Name of operator on duty / on-watch and off-watch entries
  • Call signs of stations communicated with
  • Distress, urgency, and safety traffic summaries as required
  • Equipment tests and failures
  • Ship’s position at least daily where required

Abbreviations and key letters are allowed if their meaning is explained in the same log.

Safety communications on VHF are not all required to be logged the same way as non-VHF safety traffic affecting the ship—the false statement trap is “all Safety communications received on VHF must be logged.”

  • GMDSS log placement is specifically at the GMDSS operating position , not “anywhere convenient.”
  • Principal operating position and master’s control

The principal radiotelephone operating position must be in the room (or adjoining room) from which the ship is normally steered while at sea —bridge/wheelhouse context, not a remote cabin with no conning connection.

Ultimate control of service at a ship’s radio station rests with the master of the ship . The radio operator runs the equipment; the master remains responsible for the vessel.

Inspections — where to apply

Where do you make an application for inspection of a ship GMDSS radio station?

To the Engineer-in-Charge of the FCC District Office nearest the proposed place of inspection.

  • Wrong destination (common distractors) Why wrong
  • COLEM (exam manager) Administers exams, not ship inspections
  • FCC Washington, DC headquarters only Not the district inspection application path tested

Any GMDSS Maintainer as the application office Maintainers may perform work/inspections under rules, but the application for compulsory inspection is to the district Engineer-in-Charge

Compulsory ship inspections and certificates are Part 80 process items; Element 1 only needs the nearest district Engineer-in-Charge address for the application.

International and Part 80 frame

Use and operation of FCC-licensed ship stations in international waters are governed by Part 80 of the FCC Rules plus the international Radio Regulations and agreements to which the United States is a party (including SOLAS-related carriage concepts and the Great Lakes Agreement). International agreement carriage of radio for safety of life at sea classically reaches cargo ships of more than 300 gross tons and vessels carrying more than 12 passengers (passenger-ship definition threshold).

Watch + log + inspection checklist

Listening: Ch-16 always (with VTS dual-watch exception); cargo outside harbor also 2182 kHz ; DSC on 70 / 2 MHz / 8 MHz / other HF .

Silence: 2182 kHz quiet H+00 and H+30 UTC for three minutes.

Writing: responsible operator; principal (or GMDSS) operating position; strike-through corrections; 3-year distress retention.

Inspection request: Engineer-in-Charge , nearest FCC district office to the inspection site.

Command: master has ultimate control of the ship radio service.

Nail this trio—watch, log, inspection—and you complete Element 1 Subelement A (topics 1–6) ready for Subelement B communications procedures.