Study guide

18.1 DME & VOR

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

18.1 DME & VOR

Key Takeaways Explain This Topic AI

DME measures slant-range distance by timing the round-trip of interrogate/reply pulse pairs in the L-band (~962–1213 MHz)

A built-in ground-station reply delay lets DME operate accurately at close range; most airborne DME units auto-tune with the paired VOR/LOC channel

VOR operates ~108.00–117.95 MHz, references magnetic north, and defines magnetic radials from the station

VOR navigation is based on the phase difference between a reference signal and a 30 rps rotating variable signal that are in phase at magnetic north

VORTAC stations co-locate VOR azimuth with TACAN/DME ranging so one frequency selection yields both radial and distance

Last updated: August 2026

18.1 DME & VOR

Quick Answer: DME = airborne interrogator + ground transponder ; times pulse-pair round-trip in ~962–1213 MHz → slant range . Ground reply delay enables close-range operation. Most DME auto-tunes with paired VOR/LOC . VOR = 108.00–117.95 MHz ; all directions from magnetic north ; radials = magnetic lines from station; principle = phase difference between reference and 30 rps variable signal, in phase at magnetic north .

Topic 3-K (Aircraft) opens with the two classic enroute navaids GROL techs still find on virtually every IFR airframe: Distance Measuring Equipment (DME) and VHF Omnidirectional Range (VOR) . Key topics 068 and 069 test frequencies, geometry words (slant range, radial), and the physical principle each system uses— time for DME, phase for VOR.

Distance Measuring Equipment (DME) — interrogator / transponder

DME is a secondary-radar ranging system. The aircraft unit is the interrogator ; the ground station is the transponder (often co-located with a VOR or as part of a VORTAC / TACAN suite).

  • Role Location Function
  • Interrogator Aircraft Transmits pulse-pair interrogations; measures reply delay; displays distance
  • Transponder Ground (or TACAN) Receives interrogation, waits a fixed delay, replies on paired channel
  • Display Cockpit Nautical miles (and often groundspeed / time-to-station when tracking)
  • Operating principle (pool anchor)

The main underlying operating principle of airborne DME is that a measurable amount of time is required to send and receive a radio signal through the Earth’s atmosphere . Radio waves travel at (essentially) the speed of light. The airborne computer converts the measured round-trip interval—minus the known ground-station processing delay—into distance.

Pool wording also singles out DME as the aid that determines distance to a selected VORTAC by measuring the length of time the radio signal takes to travel to and from the station .

Frequency range

Element 3 states the DME frequency range used to indicate slant-range distance as 962 MHz to 1213 MHz (L-band). Do not confuse this with:

  • Band / system Approx. frequencies Role
  • DME 962–1213 MHz Slant-range distance
  • VOR 108.00–117.95 MHz Azimuth / radials
  • Localizer 108.10–111.95 MHz Runway centerline (ILS)
  • Glideslope 329.15–335.00 MHz Vertical path (ILS)
  • Slant range (not map distance)

The distance DME reports is slant range —the straight-line path through the air from aircraft to ground station—not the horizontal ground distance a chart might suggest. Directly overhead a station, DME still shows roughly the aircraft’s height in nautical miles; far away at low altitude, slant range ≈ ground range. Pool term for “distance from the aircraft to the DME ground station”: the slant range (not “DME bearing,” “glide slope angle,” or “localizer course width”).

Built-in reply delay and close-range operation

The ground station inserts a fixed delay between reception of an interrogation and transmission of the reply. That intentional hold-off allows operation at close range —without the delay, very short geometric times would be hard to process cleanly and the airborne unit could not separate its own transmit pulse from the reply. Pool distractors (“someone to answer the call,” “VOR mechanical hook-up,” “clear other traffic”) are wrong; the technical purpose is close-range operation .

Channel pairing with VOR / LOC

The majority of airborne DME systems automatically tune their transmitter and receiver frequencies to the paired VOR/LOC channel. When the pilot (or FMS) selects a VOR or localizer frequency, the DME receiver/transmitter pair selects the standardized L-band channel assigned to that VHF navaid. That is why a single NAV radio frequency selection often yields radial + distance on a VORTAC or localizer course + DME on many ILS/DME approaches.

Service notes for GROL maintainers

Verify antenna condition (blade/L-band) and coax integrity—high VSWR kills interrogation power and reply sensitivity.

Confirm channel pairing tables when a DME “won’t lock” after a NAV frequency change.

Expect slant-range complaints over the station; explain geometry before condemning the unit.

Ground-station saturation (too many aircraft interrogating one transponder) can reduce reply rate—an operational limit, not always a failed interrogator.

Co-located TACAN provides military-compatible ranging/azimuth; civil aircraft still extract DME distance from the TACAN pulse structure.

VHF Omnidirectional Range (VOR)

VOR is the classic VHF azimuth navaid. A ground station radiates a complex signal from which any aircraft can determine its magnetic bearing from the station —a radial .

Frequency range

Ground-based VOR stations used for aircraft navigation operate 108.00 MHz to 117.95 MHz . That band is shared allocation space with localizer channels in the lower portion (odd-tenth localizer frequencies live in 108.10–111.95 MHz); service techs must know which selected frequency is a VOR vs a LOC by chart/channel plan, not by “any number in the 108s.”

Magnetic north and radials

All directions associated with a VOR station are related to magnetic north (not true north / the geographic pole / the North Star). Lines drawn from the VOR station in a particular magnetic direction are radials . The 090° radial is the magnetic line east of the station; an aircraft on the 090° radial is east of the VOR regardless of the aircraft’s heading.

  • Term Meaning
  • Radial Magnetic bearing from the VOR

Bearing / course TO Direction to fly toward the station (reciprocal of the radial you are on, when tracking inbound)

  • OBS / CDI Omni Bearing Selector and Course Deviation Indicator used to set and fly a selected course
  • TO / FROM Flag or arrow sense: whether flying the selected course takes you toward or away from the station
  • Phase comparison—the VOR operating principle

The main underlying operating principle of VOR is that a phase difference between two AC voltages may be used to determine an aircraft’s azimuth position in relation to a selected VOR station . The station radiates:

A reference phase signal (classically frequency-modulated onto a subcarrier).

A variable phase signal (amplitude-modulated radiation pattern that effectively rotates ).

The rate that the transmitted VOR variable signal rotates is equivalent to 30 revolutions per second (30 Hz). The aircraft receiver compares the phase of the reference and variable components; that phase angle equals the magnetic radial.

The amplitude-modulated variable-phase signal and the frequency-modulated reference-phase signal are synchronized so that both signals are in phase with each other at 360 degrees North, magnetic bearing position of the VOR station. At magnetic north, phase difference = 0°; elsewhere the phase lag encodes the radial.

TO / FROM sense (how pilots use what you repair)

Selecting a course on the OBS does not change which radial the aircraft is physically on—it changes the CDI centering and the TO/FROM flag:

FROM with a centered CDI: you are on the selected radial outbound from the station.

TO with a centered CDI: you are on the reciprocal radial, tracking inbound on the selected course.

Off-scale CDI: left/right of the selected course; reverse sensing on the back course of some setups is a pilot procedure issue, but the underlying RF is still phase comparison.

GROL techs do not fly approaches for a living, but understanding TO/FROM prevents misdiagnosing a healthy receiver when the pilot simply has the wrong OBS setting or is on the opposite side of the station.

VOR + DME = rho–theta navigation

  • Quantity Source Principle
  • θ (azimuth) VOR Phase difference vs magnetic north
  • ρ (range) DME Round-trip time → slant range
  • Combined VORTAC / VOR-DME Position fix relative to the station

Before GNSS became primary, enroute and terminal navigation were built on this rho–theta pair. Element 3 still expects the classical radio principles because GROL holders install, inspect, and repair the RF hardware that generates those signals.

Frequency memory table (068–069)

  • System Frequency concept Pool fact
  • DME RF band L-band 962–1213 MHz
  • DME geometry What is measured Slant range
  • DME delay purpose Ground reply hold-off Close-range operation
  • DME principle Physics Time to send/receive RF
  • DME pairing Auto channel select VOR/LOC
  • VOR RF band VHF NAV 108.00–117.95 MHz
  • VOR reference Direction datum Magnetic north
  • VOR lines Magnetic from station Radials
  • VOR rotation Variable signal 30 rps
  • VOR phase sync Zero phase 360° magnetic north
  • VOR principle Measurement Phase difference → azimuth
  • Exam-day checklist (3-K 068–069)

DME band 962–1213 MHz ; distance = slant range ; principle = time of flight .

Ground delay exists so DME can work at close range .

Airborne DME usually pairs with VOR/LOC channels.

VOR band 108.00–117.95 MHz ; directions from magnetic north ; lines = radials .

Variable signal 30 rps ; signals in phase at magnetic north ; principle = phase difference for azimuth (not distance).

Do not mix DME L-band numbers with VOR VHF or glideslope UHF distractors.

Master time-for-DME and phase-for-VOR and the 068–069 items become mechanical. Next section adds precision approach ( ILS ), low-frequency bearings ( ADF/NDB ), and ATC transponders .