Study guide

18.2 ILS, ADF & ATC Transponders

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

18.2 ILS, ADF & ATC Transponders

Key Takeaways Explain This Topic AI

ILS guidance uses a VHF localizer (≈108.10–111.95 MHz) for left/right runway centerline and a UHF glideslope (≈329.15–335 MHz) for vertical path

Localizer and glideslope each compare 90 Hz and 150 Hz amplitude-modulated patterns; marker beacons share 75 MHz carriers with 400/1300/3000 Hz tones

ADF receives LF–MF NDBs (and often broadcast AM) in about 190–1750 kHz and indicates relative bearing; “night effect” is ionospheric bounce of NDB signals

Mode A provides the ATC squawk code; Mode C adds pressure-altitude encoding; Mode S adds selective addressing and collision-avoidance capability

ATCRBS Mode C aircraft receive interrogations at 1030 MHz and reply at 1090 MHz using pulse-position modulation

Last updated: August 2026

18.2 ILS, ADF & ATC Transponders

Quick Answer: ILS = localizer (horizontal, 108.10–111.95 MHz , 90/150 Hz left/right) + glideslope (vertical, ~329.15–335 MHz ) + optional marker beacons ( 75 MHz , tones 400 / 1300 / 3000 Hz ). ADF = 190–1750 kHz relative bearing to NDB ; night effect = ionospheric multipath. Mode A = squawk; Mode C = + pressure altitude ; Mode S = + selective address / collision avoidance . ATCRBS: RX 1030 MHz , TX 1090 MHz , pulse-position modulation .

Key topics 070 (ILS) and 071 (ADF & Transponders) move from enroute navaids to precision approach and surveillance. GROL maintainers support the RF paths that keep aircraft on the centerline and visible to ATC radar.

Instrument Landing System (ILS)

An ILS provides precision approach guidance to a runway. Functionally:

  • Function Component What the pilot sees
  • Horizontal guidance Localizer (LOC) Deviation left or right of runway centerline
  • Vertical guidance Glideslope (G/S) Deviation above or below the approach path
  • Range checkpoints Marker beacons (and/or DME) Aural tone + panel light at fixed points
  • Visual segment Approach / runway lights Transition to landing visually
  • Localizer — frequency and meaning

Element 3 places the localizer beam system used to find runway centerline at 108.10 MHz to 111.95 MHz (VHF, odd-tenth channels in the lower NAV band). On runway approach, the ILS localizer shows deviation left or right of runway center line —not groundspeed, wind, or vertical error.

A required ILS component emphasized on the pool is the localizer: shows aircraft deviation horizontally from center of runway . Altimeters, VHF COM, and DME may appear on the same flight, but they are not the defining horizontal ILS guidance element.

Localizer 90 Hz / 150 Hz patterns

The localizer produces two amplitude-modulated antenna patterns : one pattern with an audio frequency of 90 Hz and one with 150 Hz , one left of the runway centerline and one right of the runway centerline. The airborne receiver compares the depth of 90 Hz vs 150 Hz modulation; equal modulation means on centerline. (The glideslope uses the same 90/150 Hz idea oriented above/below the path—do not reverse which pair is left/right vs up/down on exam day.)

Glideslope — vertical path

The glideslope transmitter operates in the UHF band near 329.15–335.00 MHz (pool distractors use this range; it is the classic glideslope assignment paired to each localizer channel). Selecting the localizer frequency on a modern NAV radio auto-tunes the paired glideslope channel—mirroring the DME pairing concept from Section 18.1.

Element 3 asks for the aircraft ILS glideslope installation antenna type: a folded dipole reception antenna . That is a receive-only, horizontally polarized antenna matched to the UHF glideslope band—not a transmitting phased array and not the ADF loop.

Marker beacons

Marker beacons mark fixed points along the approach. Element 3 states that the outer, middle, and inner marker beacon carrier frequencies are all 75 MHz , but they are 95% tone-modulated at:

  • Marker Tone Typical cockpit light (classic)
  • Outer 400 Hz Blue
  • Middle 1300 Hz Amber
  • Inner 3000 Hz White

As the aircraft passes over a beacon, the receiver produces the distinctive aural tone and panel light . Markers do not provide continuous distance-to-runway readout (that is DME/GPS); they confirm passage over fixed points. Many modern approaches substitute DME or GPS fixes for aging middle/inner markers, but the Element 3 pool still tests the 75 MHz / tone facts.

ILS frequency cheat sheet

  • Signal Band Element 3 range / note
  • Localizer VHF 108.10–111.95 MHz
  • Glideslope UHF ~329.15–335.00 MHz (paired)
  • Marker beacon VHF 75 MHz carriers; 400 / 1300 / 3000 Hz tones
  • Associated DME L-band Often auto-paired for distance
  • Automatic Direction Finder (ADF) & Non-Directional Beacons (NDB)

ADF is the airborne receiver/display that points toward a ground NDB (or, historically, a commercial AM broadcast station). Element 3 frequency range for aircraft ADF equipment: 190 kHz to 1750 kHz (LF–MF). That is kilohertz , not megahertz—common distractors put ADF in the VOR or localizer VHF band.

What ADF provides

ADF indicates the relative bearing from the aircraft’s nose to the selected NDB (or other tuned station). It does not measure slant-range distance (DME does) and does not decode weather radar imagery.

Night effect

Night effect refers to the fact that NDB transmissions can bounce off the Earth’s ionosphere at night and be received from almost any direction . Sky-wave multipath rotates or confuses the apparent bearing—especially around sunrise/sunset. NDBs are not “turned off at dusk,” and dew on the antenna is not the pool definition of night effect.

Propagation literacy (correct ADF statement)

ADF antennas can receive transmissions over the Earth’s horizon (sometimes several hundred miles) because LF–MF ground-wave signals follow the curvature of the Earth . That is the opposite of pure VHF line-of-sight VOR/localizer behavior. Classic ADF installations use a loop (directional null) plus a sense antenna to resolve 180° ambiguity—pool items reject “sense antenna alone” as sufficient for full bearing processing.

Commercial standard broadcast stations in roughly 550–1660 kHz historically could be used as navigational signals within the ADF band; the pool’s “only correct statement” items emphasize ground-wave reach and proper antenna function rather than claiming every frequency except broadcast is an NDB.

ATC transponders (ATCRBS) — Modes A, C, and S

Secondary surveillance radar ( ATCRBS —Air Traffic Control Radar Beacon System) interrogates aircraft transponders instead of relying only on primary skin paint.

Frequencies

For an aircraft Mode C transponder in ATCRBS:

  • Receive (interrogation uplink): 1030 MHz
  • Transmit (reply downlink): 1090 MHz

Memorize the direction: aircraft listens on 1030 , talks on 1090 . Swapping the numbers is the most common exam trap.

Mode functions

  • Mode What the reply carries Exam takeaway
  • Mode A 4-digit identification (squawk) code Basic identity only
  • Mode C Mode A code + pressure-altitude encoding Altitude reporting to ATC radar

Mode S Selective address; can also provide mid-air collision avoidance capabilities (beyond Mode C functions) Discrete addressing + ACAS/TCAS support

Mode C is the answer when the question asks which mode adds pressure-altitude reporting to the basic identification code. Modes 1 and 2 are military identification modes—not the civil Mode C altitude answer.

Mode S , in addition to duplicating Mode C functions, can also provide mid-air collision avoidance capabilities (the pool’s wording). It is not “primary radar,” lightning detection, or a backup VHF voice radio.

Encoding: pulse position modulation

The type of encoding used in an aircraft’s Mode C transponder transmission to an ATCRBS ground station is pulse position modulation (PPM) . Distractors such as differential phase-shift keying, Doppler compression, or “95% AM” belong to other systems.

Altitude is encoded from the aircraft’s encoding altimeter / air data computer in standard pressure-altitude steps; ATC’s ground system converts that report for controller displays. When altitude readout is wrong, techs check the encoder interface and data path , not only the RF power of the 1090 MHz reply.

Transponder service notes

Antenna : L-band blade/monopole with a good ground plane (Section 18.3).

Suppression : Coordinate with DME/TCAS so simultaneous L-band systems do not desense each other.

Self-test / ramp test sets : Verify Mode A code, Mode C altitude, and Mode S address without radiating into open hangars unlawfully.

  • 1090 MHz replies must meet power and timing specs—weak replies look like “radar doesn’t see me.”
  • Putting approach and surveillance together

On a typical IFR approach day:

Enroute — VOR radial + DME slant range (18.1).

Transition — vectors or procedure turn onto the localizer.

Final — localizer left/right + glideslope up/down; markers/DME for range.

Always — Mode C/S altitude and squawk for ATC separation.

Backup bearing — ADF/NDB still appears on some approaches and Element 3 items even as GNSS dominates ops.

Exam-day checklist (3-K 070–071)

Localizer 108.10–111.95 MHz ; shows left/right of centerline ; 90/150 Hz AM patterns left/right.

Glideslope ~329–335 MHz UHF; aircraft antenna often a folded dipole receive antenna.

Markers: all 75 MHz ; tones 400 / 1300 / 3000 Hz (outer/middle/inner).

ADF 190–1750 kHz ; relative bearing; night effect = ionospheric bounce; ground-wave can go beyond horizon .

Transponder: RX 1030 / TX 1090 MHz; Mode C adds altitude; Mode S adds selective / collision-avoidance capability; encoding = PPM .

Next section maps aircraft antennas, COM/ELT/altimeter frequencies, and equipment-function identification items (3-K 072–073).