Study guide

16.2 Voltage, Current & Impedance on Antennas

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

16.2 Voltage, Current & Impedance on Antennas

Key Takeaways Explain This Topic AI

On a resonant half-wave center-fed dipole, current is maximum and voltage is minimum at the center feedpoint; at the open ends, voltage is maximum and current is minimum

Feedpoint impedance at resonance is essentially resistive (≈ Rr + RL); off resonance, capacitive or inductive reactance appears and SWR rises on a fixed-Z0 line

Practical half-wave length is about 468/f_MHz feet; quarter-wave verticals use about 234/f_MHz feet plus a ground plane or radials that complete the RF return

Line current from power and impedance uses I = √(P/R); example: 1,872 W into 52 Ω → 6 A

Forward power minus reflected power is the power accepted by the antenna system; harmonic attenuation in dB is 10 log(P_fundamental/P_harmonic)

Last updated: August 2026

16.2 Voltage, Current & Impedance on Antennas

Quick Answer: On a half-wave dipole, ends = max voltage / min current ; center feed = max current / min voltage . Resonance ≈ 468/f MHz feet (half-wave). Matched line: I = P / R I = \sqrt{P/R} I = P / R ​ ( 1,872 W / 52 Ω → 6 A ). Best SWR = 1:1 . Accepted power ≈ forward − reflected . Harmonic attenuation: 10 log(P1/P2) ( 500 W / 0.5 W → 30 dB ).

Key topic 3-J-064 (Voltage, Current and Power Relationships) is pure distribution math. If you can sketch voltage and current along a half-wave and compute line current and reflected-power budgets, most of this group is mechanical.

Standing waves of V and I on a half-wave dipole

A resonant center-fed half-wave antenna supports a standing wave of RF voltage and current along its length (one half-cycle of the spatial distribution).

  • Location on λ/2 dipole RF current RF voltage Impedance character
  • Center (feedpoint) Maximum Minimum Low-Z, ~resistive at resonance (~50–75 Ω class)
  • Mid-element Intermediate Intermediate Rising Z toward ends
  • Open ends Minimum (≈ 0) Maximum High-Z; end insulators see high RF voltage

Pool wording: at the ends of a half-wave antenna you have maximum voltage and minimum current compared with the remainder of the antenna. That is why end insulators, corona balls, and clearance matter on HF wire antennas—RF voltage peaks can arc to nearby metal.

Why the center is a natural feedpoint

High current and moderate voltage at the center produce a convenient low impedance that matches common coax. Feeding a half-wave at an end would present a very high impedance and need a different matching network (as in some end-fed designs).

Receive side note

The voltage produced in a receiving antenna is always proportional to the received field strength (for a given antenna effective height/length and polarization alignment). Stronger E-field → larger open-circuit induced voltage. Phase quirks from wrong length or SWR are not the pool’s primary receive-voltage rule— field strength proportionality is.

Resonance length and feedpoint impedance

Half-wave (Hertz) length L λ / 2 ( f t ) ≈ 468 f M H z L_{\lambda/2\,(\mathrm{ft})} \approx \frac{468}{f_{\mathrm{MHz}}} L λ /2 ( ft ) ​ ≈ f MHz ​ 468 ​

Worked examples:

  • Frequency Approx. half-wave length
  • 7.0 MHz 468/7 ≈ 66.9 ft
  • 14.2 MHz 468/14.2 ≈ 33.0 ft
  • 150 MHz 468/150 ≈ 3.12 ft (~1 m)

Slightly longer or shorter than resonance introduces inductive or capacitive reactance at the feedpoint. A matching network (coupler) or physical trim restores a near-resistive match.

Quarter-wave vertical + ground plane L λ / 4 ( f t ) ≈ 234 f M H z L_{\lambda/4\,(\mathrm{ft})} \approx \frac{234}{f_{\mathrm{MHz}}} L λ /4 ( ft ) ​ ≈ f MHz ​ 234 ​

The ground plane or radials provide the RF return image. Poor ground (few radials, rusty bonds, small aircraft skin discontinuities) raises loss resistance, lowers efficiency, and can shift feedpoint Z and pattern. Ship and tower grounds must be low RF impedance , not merely “a green wire somewhere.”

  • Installation Ground system role
  • Ship HF whip Bond to superstructure / counterpoise per design
  • Land base vertical Radial field or ground screen
  • Vehicle/aircraft Body/skin as ground plane; verify bonding straps
  • Feedpoint impedance summary

At resonance , feedpoint impedance ≈ Rr + RL (resistive). Off resonance , ±jX appears. The transmission line wants to see a load equal to its characteristic impedance Z0 (commonly 50 Ω for radio coax). Mismatch → reflections → SWR > 1 .

Current on a matched transmission line

For a line delivering real power P into a resistive load R equal to Z0 : P = I 2 R ⇒ I = P R P = I^2 R \quad \Rightarrow \quad I = \sqrt{\frac{P}{R}} P = I 2 R ⇒ I = R P ​ ​

Worked example (pool): current on a 52 Ω line with 1,872 W input: I = 1872 52 = 36 = 6 A I = \sqrt{\frac{1872}{52}} = \sqrt{36} = \mathbf{6\ A} I = 52 1872 ​ ​ = 36 ​ = 6 A

Also V = P R = 1872 × 52 = 97344 = 312 V V = \sqrt{P R} = \sqrt{1872 \times 52} = \sqrt{97344} = 312\,\mathrm{V} V = PR ​ = 1872 × 52 ​ = 97344 ​ = 312 V RMS, and P = V I = 312 × 6 = 1872 W P = V I = 312 \times 6 = 1872\,\mathrm{W} P = V I = 312 × 6 = 1872 W —useful cross-check.

  • P (W) R (Ω) I (A)
  • 100 50 √2 ≈ 1.41
  • 1,872 52 6
  • 25 50 0.707

Use RMS RF current for heating and ammeter comparisons; peak is √2 higher for sine waves.

Standing wave ratio (SWR) quality

SWR (or VSWR) compares the maximum and minimum RF voltage (or current) magnitudes along a line caused by reflections. Perfect match: S W R = 1 : 1 \mathrm{SWR} = 1:1 SWR = 1 : 1

Best standing wave ratio on the pool: 1:1. Larger ratios (1:1.5, 1:3, 1:4) mean more reflected power, hotter line, possible PA stress, and less power accepted by the antenna. Many solid-state transmitters fold back as SWR rises.

  • SWR Qualitative match
  • 1:1 Ideal match
  • ≤ 1.5:1 Usually excellent for solid-state gear
  • ~2:1 Acceptable in many HF systems with care
  • ≥ 3:1 Investigate length, feed, coupler, opens/shorts
  • Forward, reflected, and “actually radiated” power

A directional wattmeter separates forward (incident) and reflected power. Power accepted by the load (antenna + losses) is approximately: P a c c e p t e d = P f o r w a r d − P r e f l e c t e d P_{\mathrm{accepted}} = P_{\mathrm{forward}} - P_{\mathrm{reflected}} P accepted ​ = P forward ​ − P reflected ​

Worked example (pool): 30 W transmitter into a mismatched antenna with 5 W reflected : P ≈ 30 − 5 = 25 W P \approx 30 - 5 = \mathbf{25\ W} P ≈ 30 − 5 = 25 W

(The pool phrases this as power “actually radiated” in the simplified model—real systems also convert some accepted power to heat in conductors and ground. For exam arithmetic, forward − reflected is the move.)

Harmonic attenuation in dB

If the antenna (or system) radiates 500 W at the fundamental and 0.5 W at the second harmonic: A d B = 10 log ⁡ 10 ( 500 0.5 ) = 10 log ⁡ 10 ( 1000 ) = 30 d B A_{\mathrm{dB}} = 10\log_{10}\left(\frac{500}{0.5}\right) = 10\log_{10}(1000) = \mathbf{30\ dB} A dB ​ = 10 lo g 10 ​ ( 0.5 500 ​ ) = 10 lo g 10 ​ ( 1000 ) = 30 dB

That is a power ratio of 1,000:1 . Filters, PA design, and antenna resonance all contribute to harmonic cleanliness—Element 3 ties the number to the log definition from Chapter 7.

  • P_fund / P_harm Attenuation
  • 10 10 dB
  • 100 20 dB
  • 1,000 30 dB
  • 10,000 40 dB
  • Connecting impedance pictures to the coupler

An antenna coupler (tuner) transforms a non-50 Ω or reactive antenna impedance into a value the transmitter and line can accept. When the coupler is detuned , the match collapses, SWR rises, reflected power climbs, and accepted power falls—even if the PA meter still shows high forward power into a bad load. Always re-tune after frequency changes on multi-band HF marine and aeronautical installations.

Ground-plane effects on impedance

Raising a dipole higher above ground, adding radials under a vertical, or bonding a ship whip to a larger metal mass all change the reactive environment and slightly shift resonant frequency and feed Z. After mechanical changes (new mount, longer lead-in, damaged radial), re-measure SWR and retune; do not assume the old coupler settings remain valid.

Exam-day V/I/power checklist (3-J-064)

Half-wave ends : V max, I min ; center : I max, V min .

Length ≈ 468/f MHz feet (λ/2); λ/4 ≈ 234/f .

Receive antenna voltage ∝ field strength .

I = P / R I = \sqrt{P/R} I = P / R ​ → 6 A for 1,872 W / 52 Ω.

Best SWR = 1:1 .

Accepted ≈ forward − reflected (30 − 5 = 25 W ).

Harmonic attenuation 10 log(P1/P2) → 30 dB for 500 W / 0.5 W.

Ground plane/radials complete the vertical’s RF circuit and affect Z and efficiency.

Next: transmission lines —Z0, velocity factor, stubs, nitrogen, and loss/SWR behavior that connect the PA to this feedpoint.