Study guide

16.4 Effective Radiated Power & Antenna Bandwidth

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

16.4 Effective Radiated Power & Antenna Bandwidth

Key Takeaways Explain This Topic AI

ERP multiplies transmitter output by linear antenna gain and accounts for feedline/duplexer losses: net dB = G_ant − L_line − L_duplexer (and similar), then P_ERP = P_TX × 10^(net_dB/10)

EIRP is ERP-style power referenced to isotropic (dBi); ERP is often referenced to a half-wave dipole—EIRP ≈ ERP × 1.64 (about +2.15 dB) when the same pattern is compared carefully

Antenna bandwidth is the frequency range over which the antenna performs well (acceptable SWR/gain/pattern)—not beamwidth and not “length divided by elements”

Series inductance (loading coils) electrically lengthens an antenna and lowers resonant frequency; series capacitance raises resonant frequency; loading coils that physically shorten a radiator also decrease bandwidth

  • Pool ERP drill: 50 W with −4 dB line, −3 dB duplexer, +6 dB antenna → net −1 dB → ≈ 39.7 W ERP
  • Last updated: August 2026

16.4 Effective Radiated Power & Antenna Bandwidth

Quick Answer: ERP = transmitter power adjusted by antenna gain and line/duplexer losses using dB: P E R P = P T X × 10 ( n e t d B ) / 10 P_{\mathrm{ERP}} = P_{\mathrm{TX}} \times 10^{(\mathrm{net\ dB})/10} P ERP ​ = P TX ​ × 1 0 ( net dB ) /10 . EIRP uses an isotropic reference ( dBi ); classic ERP often uses a dipole reference. Antenna bandwidth = frequency range of good performance. Series L lowers resonance (electrically longer); series C raises it; loading coils that shorten a whip also narrow bandwidth .

Key topics 3-J-065 (Frequency and Bandwidth) and 3-J-067 (Effective Radiated Power) finish Topic 3-J. One half is resonance craft; the other is the ERP arithmetic that shows up repeatedly on Element 3—and on real repeater and base-station paperwork.

Effective radiated power (ERP)

ERP answers: “How strong is the station in free space compared with a reference antenna fed with a known power?” You start with transmitter power output (TPO) , subtract real losses, and add antenna gain.

dB method (preferred)

Convert every gain and loss to dB (antenna gain positive; feedline, duplexers, circulators, filters as negative losses).

Sum the net: n e t d B = G a n t ( d B ) − L f e e d ( d B ) − L d u p l e x / c i r c ( d B ) − ⋯ \mathrm{net\ dB} = G_{\mathrm{ant(dB)}} - L_{\mathrm{feed(dB)}} - L_{\mathrm{duplex/circ(dB)}} - \cdots net dB = G ant ( dB ) ​ − L feed ( dB ) ​ − L duplex/circ ( dB ) ​ − ⋯

Apply to TPO: P E R P = P T X × 10 ( n e t d B ) / 10 P_{\mathrm{ERP}} = P_{\mathrm{TX}} \times 10^{(\mathrm{net\ dB})/10} P ERP ​ = P TX ​ × 1 0 ( net dB ) /10

Linear method (same math)

Convert each dB figure to a power ratio 10 d B / 10 10^{dB/10} 1 0 d B /10 , multiply gains, divide by loss ratios: P E R P = P T X × g a n t × ℓ f e e d × ℓ d u p l e x P_{\mathrm{ERP}} = P_{\mathrm{TX}} \times g_{\mathrm{ant}} \times \ell_{\mathrm{feed}} \times \ell_{\mathrm{duplex}} P ERP ​ = P TX ​ × g ant ​ × ℓ feed ​ × ℓ duplex ​

where each ℓ < 1 \ell < 1 ℓ < 1 for losses.

Worked pool examples (memorize the pattern)

Example A: 50 W TX, 4 dB feedline loss, 3 dB duplexer/circulator loss, 6 dB antenna gain: n e t = 6 − 4 − 3 = − 1 d B \mathrm{net} = 6 - 4 - 3 = -1\,\mathrm{dB} net = 6 − 4 − 3 = − 1 dB P E R P = 50 × 10 − 0.1 ≈ 50 × 0.794 = 39.7 W P_{\mathrm{ERP}} = 50 \times 10^{-0.1} \approx 50 \times 0.794 = \mathbf{39.7\ W} P ERP ​ = 50 × 1 0 − 0.1 ≈ 50 × 0.794 = 39.7 W

Example B: 75 W, −4 dB line, −3 dB duplex, +10 dB antenna → net +3 dB → 75 × 2 ≈ 150 W 75 \times 2 \approx \mathbf{150\ W} 75 × 2 ≈ 150 W .

Example C: 75 W, −5, −4, +6 → net −3 dB → 75 × 0.5 = 37.5 ≈ 37.6 W 75 \times 0.5 = \mathbf{37.5\ ≈ 37.6\ W} 75 × 0.5 = 37.5 ≈ 37.6 W .

Example D: 100 W, −4, −3, +7 → net 0 dB → 100 W ERP.

Example E: 100 W, −5, −4, +10 → net +1 dB → 100 × 1.26 ≈ 126 W 100 \times 1.26 \approx \mathbf{126\ W} 100 × 1.26 ≈ 126 W .

Example F: 50 W, −5, −4, +7 → net −2 dB → 50 × 0.631 ≈ 31.5 W 50 \times 0.631 \approx \mathbf{31.5\ W} 50 × 0.631 ≈ 31.5 W .

  • Memory anchors
  • ±1 dB ≈ ×1.26 or ×0.79
  • ±2 dB ≈ ×1.58 or ×0.63
  • ±3 dB = ×2 or ×0.5
  • 0 dB net → ERP = TPO
  • ERP vs EIRP
  • Quantity Reference antenna Practical note
  • ERP Often half-wave dipole Common in land-mobile / older FCC wording
  • EIRP Isotropic Common in satellite, microwave, modern datasheets

Because a dipole has about 2.15 dBi gain: E I R P d B W ≈ E R P d B W + 2.15 \mathrm{EIRP_{dBW}} \approx \mathrm{ERP_{dBW}} + 2.15 EIR P dBW ​ ≈ ER P dBW ​ + 2.15

or in linear power, EIRP ≈ 1.64 × ERP when both describe the same physical field and the ERP reference is a dipole. Always read the regulation or datasheet: mixing ERP and EIRP without the 2.15 dB bridge is a classic paperwork error. Element 3’s 3-J-067 items are labeled effective radiated power and use the dB sum method above—drill those six numerical patterns until they are automatic.

Where the power path sits TX → L j u m p e r duplexer/filter → L f e e d antenna → G a n t free space (ERP) \textbf{TX} \xrightarrow{L_{\mathrm{jumper}}} \textbf{duplexer/filter} \xrightarrow{L_{\mathrm{feed}}} \textbf{antenna} \xrightarrow{G_{\mathrm{ant}}} \textbf{free space (ERP)} TX L jumper ​ ​ duplexer/filter L feed ​ ​ antenna G ant ​ ​ free space (ERP)

Section 16.3’s 6 W at the end of a lossy run is exactly the P T X × ℓ f e e d P_{\mathrm{TX}}\times\ell_{\mathrm{feed}} P TX ​ × ℓ feed ​ factor before antenna gain multiplies what is left. High antenna gain cannot fully rescue terrible feedline loss—and a high-gain antenna with a failed jumper still yields poor ERP.

Antenna bandwidth and Q

Antenna bandwidth (pool definition): the frequency range over which an antenna can be expected to perform well . “Perform well” usually means SWR under a limit (e.g., 2:1), gain and pattern still useful, and efficiency acceptable.

Bandwidth is not :

  • Beamwidth (an angle on the pattern),
  • Element length divided by number of elements,

The geometric angle between element tips.

Resonance shifts with L and C

A Hertz (half-wave) antenna’s resonant frequency can be lowered by placing an inductance in series with the antenna—series L adds electrical length. Conversely, to lengthen an antenna electrically, add a coil (loading inductor).

To increase the resonant frequency of a λ/4 antenna, add a capacitor in series —series C makes the antenna electrically shorter, raising fr . (Physically cutting the element also raises resonance; the pool’s component answer is series C for the “increase fr” item.)

  • Goal Typical reactance action
  • Lower fr / electrically longer Series inductor (coil)
  • Raise fr / electrically shorter Series capacitor
  • Multiband compromise Traps (Section 16.1)
  • Loading coils and bandwidth

Mobile and marine whips are often physically shorter than λ/4 with a loading coil restoring resonance. What happens to bandwidth as the antenna is shortened through loading coils? It is decreased. Electrically shortened, high-Q antennas are “peaky”: SWR rises quickly as you move off the design frequency. That is why a short loaded HF whip may need a coupler for every channel, while a full-size dipole covers more of a band without retuning.

Rough intuition: Q ≈ f 0 B W ⇒ B W ≈ f 0 Q Q \approx \frac{f_0}{BW} \quad \Rightarrow \quad BW \approx \frac{f_0}{Q} Q ≈ B W f 0 ​ ​ ⇒ B W ≈ Q f 0 ​ ​

Loading that raises Q (more reactance, less radiation resistance relative to stored energy) narrows BW .

Pattern reminder tied to frequency use

A vertical λ/4 still receives equally from all horizontal directions across its usable band—bandwidth limits match and efficiency , not the basic omnidirectional idea. Stay inside the antenna’s rated frequency range; far outside resonance you get high SWR, low efficiency, and possibly transmitter foldback long before the pattern “changes modes.”

Service scenarios that combine ERP and bandwidth

VHF marine base: 25 W radio, 1.5 dB jumper+feed loss, 3 dBi whip → net ≈ +1.5 dB → ERP ≈ 35 W class—verify after installation with a wattmeter at the antenna if possible.

Repeater: Large duplexers add 2–4 dB loss each way; antenna gain must overcome that or ERP falls below TPO (Examples A and F).

HF loaded whip: Coil makes the 24 ft stick resonate on 2–3 MHz, but bandwidth is narrow—retune coupler on every frequency change (Element 1 + Element 3 together).

Harmonic check: After ERP is set, confirm harmonic attenuation (Section 16.2) so legal and clean radiation accompanies the intended ERP.

Exam-day ERP & bandwidth checklist (3-J-065, 3-J-067)

ERP: net dB = Gant − Lfeed − Lduplex… ; P × 10 n e t / 10 P \times 10^{\mathrm{net}/10} P × 1 0 net /10 .

Drill anchors: 39.7 W, 150 W, 37.6 W, 100 W, 126 W, 31.5 W pool family.

EIRP ↔ isotropic; ERP often dipole-referenced; ~2.15 dB bridge.

Bandwidth = frequency range of good performance.

Series L → lower fr / longer electrically; series C → higher fr .

Loading coils on shortened antennas → decreased bandwidth .

λ/4 vertical → omnidirectional horizontally across its operating band.

Excited λ/2 → both electric and magnetic field components in the radiated wave.

Topic 3-J is complete when you can describe the radiator, sketch V/I on a half-wave, budget the feed line, compute ERP, and predict how coils and capacitors move resonance and bandwidth. Those skills transfer directly to aircraft antennas, radar arrays, and marine VHF plants in later Element 3 topics.