Study guide
16.3 Transmission Lines, Velocity Factor & SWR
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
16.3 Transmission Lines, Velocity Factor & SWR
Key Takeaways Explain This Topic AI
Characteristic impedance Z0 is set by geometry and dielectric—not by line length; common coax is 50 Ω (radio) or 75 Ω (video/CATV); parallel twin-lead is often ~300 Ω
Velocity factor VF = (wave speed on the line) / c; VF is determined by the dielectrics in the line (solid PE coax ≈ 0.66)
Electrical length = physical length / VF; mismatch at the load reflects energy and creates standing waves (SWR/VSWR > 1)
Line loss is usually stated in dB per 100 ft and doubles when length doubles—e.g., 6 dB/100 ft over 200 ft is 12 dB → 100 W becomes ~6 W
Nitrogen dry air keeps moisture out of pressurized hardline; shorted λ/4 stubs can notch even harmonics; matching networks present Z0 to the transmitter
Last updated: August 2026
16.3 Transmission Lines, Velocity Factor & SWR
Quick Answer: Z0 (e.g. 50 Ω coax, 75 Ω video, ~300 Ω twin-lead) is set by geometry + dielectric , not length. Velocity factor = v l i n e / c v_{\mathrm{line}} / c v line / c , set by dielectrics (solid PE ≈ 0.66 ). Mismatch → reflections → SWR . Loss in dB/100 ft stacks with length ( 6 dB/100 ft × 200 ft → 12 dB → 100 W → ~6 W ). Nitrogen keeps moisture out of pressurized lines.
Key topic 3-J-066 (Transmission Lines) is the cable plant between the PA wattmeter and the antenna feedpoint. GROL service work lives here: wrong Z0 adapters, waterlogged coax, ignored VF when cutting phasing lines, and unmeasured dB losses that “steal” ERP.
Why use a transmission line?
The transmitter is rarely at the antenna. A transmission line guides RF with controlled impedance so power arrives with predictable loss and phase. At low HF with short runs, almost any cable “works”; at VHF/UHF and microwave, line choice and length dominate system performance.
- Line type Typical Z0 Traits
- Coax (RG-58, RG-8, LMR, hardline) 50 Ω radio standard Shielded; flexible or rigid; weatherable
- Coax (RG-59, RG-6) 75 Ω Video/CATV; some receive systems
- Twin-lead / open-wire ~ 300 Ω (or other) Low loss when dry/clear of metal; unshielded
- Waveguide Modal impedance (microwave) Hollow metal guide; very low loss above cutoff
RG-58 and most transmitter jumpers: 50 ohms . Never assume a “TV” 75 Ω cable is interchangeable in a 50 Ω PA path without checking match and connectors.
Characteristic impedance Z0
For coax, Z0 depends on the ratio of shield diameter to center conductor diameter and on the dielectric constant of the insulator between them—not on how many feet you buy. Cutting a 50 Ω cable in half does not make it 25 Ω.
When the load impedance equals Z0 , the line is matched : energy travels one way (aside from normal attenuation); no reflection . When the load ≠ Z0, part of the wave reflects , interfering with the forward wave to form standing waves .
Velocity factor and electrical length
Waves travel slower in cable than in vacuum because fields exist partly in the dielectric.
Velocity factor (VF): V F = v l i n e c = velocity of the wave on the line velocity of light in vacuum \mathrm{VF} = \frac{v_{\mathrm{line}}}{c} = \frac{\text{velocity of the wave on the line}}{\text{velocity of light in vacuum}} VF = c v line = velocity of light in vacuum velocity of the wave on the line
What determines VF? The dielectrics in the line —not termination impedance, not length, not center-conductor resistivity alone.
- Dielectric style Approx. VF
- Solid polyethylene (classic coax) ~0.66
- Foam PE ~0.80–0.85
- Air / mostly air dielectric ~0.95–0.99
- Open-wire (mostly air) ~0.95–0.97
Electrical length: ℓ e l e c t r i c a l = ℓ p h y s i c a l V F \ell_{\mathrm{electrical}} = \frac{\ell_{\mathrm{physical}}}{\mathrm{VF}} ℓ electrical = VF ℓ physical
A physical 10 m of VF 0.66 coax is about 15.2 m of free-space electrical length. Phasing harnesses, stub lengths, and “quarter-wave” matching sections must be cut using electrical wavelength on that specific cable.
Worked example — physical length for λ/4 at 150 MHz on VF 0.66 coax: λ 0 = 2 m , λ l i n e = V F λ 0 = 1.32 m , λ / 4 = 0.33 m \lambda_0 = 2\,\mathrm{m},\quad \lambda_{\mathrm{line}} = \mathrm{VF}\,\lambda_0 = 1.32\,\mathrm{m},\quad \lambda/4 = \mathbf{0.33\ m} λ 0 = 2 m , λ line = VF λ 0 = 1.32 m , λ /4 = 0.33 m
Reflections, SWR, and matching networks
VSWR (Voltage Standing Wave Ratio) is the ratio of maximum to minimum RF voltage along the line. Equivalently from reflection coefficient magnitude |Γ|: S W R = 1 + ∣ Γ ∣ 1 − ∣ Γ ∣ \mathrm{SWR} = \frac{1 + |\Gamma|}{1 - |\Gamma|} SWR = 1 − ∣Γ∣ 1 + ∣Γ∣
- Condition Result
- Load = Z0 Γ = 0, SWR = 1:1
- Open or short |Γ| = 1, SWR → ∞ (ideally)
- Moderate mismatch SWR 1.5–3, some reflected power
Matching networks (antenna couplers, LC networks, transformers, stubs) transform antenna Z to Z0 so the transmitter sees a happy load. They do not create RF power; they reduce reflections . A detuned coupler, as in Section 16.1, is a leading cause of high SWR.
High SWR consequences for GROL maintainers:
Reflected power heats the line and PA.
Voltage maxima can arc connectors or dry coax.
Solid-state transmitters reduce power (foldback).
Common-mode currents may radiate from the feed line itself (RFI).
Line losses in decibels
Manufacturers specify attenuation in dB per 100 feet (or per 100 m) at a stated frequency. Loss rises with frequency and with water in the dielectric.
Worked example (pool): loss 6 dB per 100 feet , run 200 feet , transmitter 100 W : Total loss = 6 d B / 100 f t × 2 = 12 d B \text{Total loss} = 6\,\mathrm{dB}/100\,\mathrm{ft} \times 2 = 12\,\mathrm{dB} Total loss = 6 dB /100 ft × 2 = 12 dB P o u t = 100 × 10 − 12 / 10 = 100 / 15.85 ≈ 6 W P_{\mathrm{out}} = 100 \times 10^{-12/10} = 100 / 15.85 \approx \mathbf{6\ W} P out = 100 × 1 0 − 12/10 = 100/15.85 ≈ 6 W
(Pool answer 6 watts .) −3 dB halves power; −10 dB is a decade; −12 dB is about 1/16.
- Loss (dB) Pout / Pin
- 3 0.50
- 6 0.25
- 10 0.10
- 12 ~0.063
Another pool-style ratio: a perfect (no-loss) line described with 7 dB of reflected/returned level relative to 5 W input yields about 1 W at that −7 dB figure (5 × 10^(−0.7) ≈ 1 W)—practice reading dB power ratios fluently either as attenuation or as reflection levels.
Nitrogen in transmission lines
Large rigid coax and waveguide runs are often pressurized with dry nitrogen . Purpose on Element 3: prevent moisture from entering the line . Water raises loss, corrodes inner conductors, and can cause arcing. Nitrogen is not primarily for “improving skin effect,” “reducing SWR by magic,” or replacing a proper match—it is a dry dielectric / purge practice.
Harmonic stubs
A stub is a short section of line (open or shorted) teed across the main feed to create a frequency-selective short or open.
Pool item: a shorted stub attached to absorb even harmonics , referred to the fundamental, can be 1/4 wavelength long (at the fundamental). At the second harmonic that physical length is λ/2 , transforming the short into a short again at even harmonics in the classic stub-filter picture the pool expects—recognize λ/4 shorted stub as the stock answer for even-harmonic absorption, not 1/2 or 1.41 wavelength distractors.
Putting the line plant together
Choose Z0 compatible with radio equipment ( 50 Ω typical).
Minimize length and use low-loss cable at VHF/UHF.
Keep connectors dry; use N-type outdoors where appropriate; install PL-259 with proper center and shield bonds (no braid shorts to the pin).
Cut phasing/matching sections with VF .
Measure forward/reflected power and SWR after any antenna or coupler change.
Budget line loss before you promise ERP (next section).
Exam-day transmission-line checklist (3-J-066)
VF = v l i n e / c v_{\mathrm{line}}/c v line / c ; set by dielectrics (PE coax ≈ 0.66 ).
Z0 from geometry/dielectric; 50 Ω radio coax standard.
Mismatch → reflections → SWR > 1 ; match with coupler/network.
6 dB/100 ft × 200 ft @ 100 W → ~6 W at the antenna.
Nitrogen → keep moisture out.
Shorted λ/4 stub class answer for even-harmonic absorption.
Electrical length = physical / VF when cutting stubs and harnesses.
With power at the feedpoint understood, Section 16.4 multiplies that power by antenna gain (and subtracts remaining losses) to get ERP , and links bandwidth and loading-coil tradeoffs from 3-J-065.