Study guide
10.2 Op Amps, PLLs, VCOs & Mixers
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
10.2 Op Amps, PLLs, VCOs & Mixers
Key Takeaways Explain This Topic AI
Ideal op-amp rules for analysis: infinite open-loop gain, infinite input impedance, zero output impedance; negative feedback sets closed-loop gain
Inverting closed-loop gain is −Rf/Rin; non-inverting closed-loop gain is 1 + Rf/Rg; the inverting input sits at virtual ground in the classic inverter
A phase-locked loop (PLL) compares phase, filters the error, and steers a voltage-controlled oscillator (VCO) — a stage whose output frequency is set by a DC control voltage — until the output locks to the reference
Mixers produce sum and difference products of two inputs (heterodyning); superhet receivers convert RF to a fixed IF using LO − RF or LO + RF products
A direct digital synthesizer chains a phase comparator, look-up table, DAC and a low-pass anti-alias filter; its impurities are discrete spurs, whereas a PLL produces broadband noise
Last updated: August 2026
10.2 Op Amps, PLLs, VCOs & Mixers
Quick Answer: Ideal op-amp: infinite open-loop gain, infinite Zin, zero Zout; feedback sets gain. Inverting gain = −Rf/Rin ; non-inverting = 1 + Rf/Rg . PLL = phase detector + loop filter + VCO → lock to reference. VCO frequency follows control voltage. Mixer outputs sum and difference frequencies ( heterodyning )—the heart of the superhet.
Passive tanks set frequency and selectivity. Active practical circuits amplify cleanly , lock frequency , tune by voltage , and translate spectra from RF to IF. Element 3 Topic 3-D expects you to recognize these blocks by behavior, not to design a custom IC layout.
Operational amplifiers — the ideal model
An operational amplifier (op amp) is a high-gain differential amplifier with inverting (−) and non-inverting (+) inputs and a single-ended output (classic symbol: triangle).
Ideal op-amp rules used on exams and benches
- Ideal assumption Meaning for analysis
- Infinite open-loop voltage gain Tiny differential input voltage produces large output (until rails limit)
- Infinite input impedance No current into the + or − pins (ideal)
- Zero output impedance Output is a perfect voltage source within current limits
- Zero input offset (teaching ideal) Output zero when inputs equal
- Infinite bandwidth (ideal) Real parts roll off; closed-loop BW still finite
With negative feedback , the op amp adjusts its output so the differential input voltage is forced nearly to zero (the two inputs are at the same voltage). That single idea unlocks virtual ground and the closed-loop gain formulas.
Inverting amplifier
Signal enters through Rin to the inverting input; feedback resistor Rf from output to inverting input; non-inverting input grounded. A v = V o u t V i n = − R f R i n A_v = \frac{V_{\mathrm{out}}}{V_{\mathrm{in}}} = -\frac{R_f}{R_{\mathrm{in}}} A v = V in V out = − R in R f
- Feature Value
- Closed-loop gain −Rf / Rin (magnitude Rf/Rin)
- Phase 180° inversion
- Inverting-node voltage Virtual ground (≈ 0 V) with feedback
- Input resistance (approx) ≈ Rin
Why virtual ground? Negative feedback holds the inverting input at the same potential as the grounded non-inverting input—about 0 V—while current through Rin continues through Rf (ideally no pin current).
- Worked example — inverting gain
- Rin = 10 kΩ , Rf = 100 kΩ : A v = − 100 10 = − 10 A_v = -\frac{100}{10} = -10 A v = − 10 100 = − 10
A 0.1 V peak input → −1.0 V peak output (within supply rails). Swap to Rf = 47 kΩ → gain ≈ −4.7.
Non-inverting amplifier
Signal drives the non-inverting input. Feedback divider Rg (ground) and Rf (to output) sets the fraction returned to the inverting input. A v = 1 + R f R g A_v = 1 + \frac{R_f}{R_g} A v = 1 + R g R f
- Feature Value
- Closed-loop gain 1 + Rf/Rg (always ≥ 1 for this topology)
- Phase No inversion
- Input resistance Very high (≈ op-amp Zin with feedback)
- Unity-gain special case Rf = 0 or follower wiring → voltage follower , gain = 1
- Worked example — non-inverting gain
- Rf = 22 kΩ , Rg = 10 kΩ : A v = 1 + 22 10 = 3.2 A_v = 1 + \frac{22}{10} = 3.2 A v = 1 + 10 22 = 3.2
- Op-amp roles in radio equipment
- Application Typical topology
- Audio mic preamp / line amp Non-inverting or inverting with defined gain
- Active filter / tone control Op amp + RC feedback networks
- DC servo / AGC control amp Integrator-like or high-gain error amp
- Buffer between stages Voltage follower
- Comparator (open-loop or with positive feedback) Threshold detection, squelch logic
Supply note: Real op amps need power rails (split ± or single-supply with bias). Clipping against the rails is the usual limit when calculated gain × input exceeds available swing—exactly what you see as flat-topped audio on a scope.
Voltage-controlled oscillators (VCOs)
A VCO produces an AC output whose frequency depends on a control voltage . Raise the tuning voltage and f_out rises (or falls, depending on design); the control law is often approximately linear over a design range.
- Piece Role
- Resonator / multivibrator core Sets free-run frequency band
- Varactor or voltage-variable element Steers C (or timing) with DC
- Buffer Isolates load pull
- Control voltage pin Synthesizer, PLL, or modulation input
FM connection: If the control voltage carries audio, the VCO becomes a direct FM generator . If the control voltage is a filtered PLL error, the VCO becomes the tunable LO inside a synthesizer.
GROL maintainers meet VCOs as “the LO synthesizer brick” on modern VHF marine, aviation COM, and HF gear: wrong lock voltage, open varactor bias, or contaminated control line → off-frequency or unlocked operation.
Phase-locked loops (PLLs)
A phase-locked loop forces a VCO to track a reference in phase (and therefore in frequency, once locked).
- Classic three-block PLL Reference ──► Phase ──► Loop ──► VCO ──► Output
- detector filter │
- ▲ │
- └────── feedback ──┘
- (often ÷N in synthesizers)
Block Function
Phase detector (PD) / phase-frequency detector Compares reference phase to VCO (or divided VCO) phase; outputs error
- Loop filter Low-pass filters the PD output into a clean DC control voltage ; sets loop dynamics
- VCO Converts control voltage to frequency; output is the locked oscillator
In frequency synthesizers , a programmable divider (÷N) sits in the feedback path so f o u t = N × f r e f f_{\mathrm{out}} = N \times f_{\mathrm{ref}} f out = N × f ref
(or a fractional-N variant). Channel step size relates to reference and division architecture—the conceptual Element 3 point is lock the VCO to a stable reference via feedback .
Lock range vs capture range
- Term Meaning
- Lock range Frequency range over which the PLL holds lock once already locked (often wider)
- Capture range Frequency range over which the PLL can acquire lock from an unlocked condition (often narrower)
- Locked VCO tracks reference; steady (or slowly modulated) control voltage
- Unlocked / out of lock Beat notes, hunting control voltage, wrong frequency, “fail” indicators on some gear
Shop symptoms of unlock: no transmit on frequency, receiver dead on channel, synthesizer unlock LED/alarm, warbling or multiple spurs. Causes include wrong reference (dead TCXO), bad loop filter caps, VCO not covering band, programming error on ÷N, or supply ripple on the control line.
PLL uses in radiotelephone gear
Channelized LO synthesis for RX/TX.
Carrier recovery or coherent detectors in some data modes.
Clock cleaning / reference distribution on digital radio boards.
FM demodulation (PLL discriminator topologies)—advanced but same blocks.
Mixers and heterodyning
A mixer is a nonlinear (or switching) circuit with two inputs that produces output components at the sum and difference of the input frequencies—and usually the originals and harmonics depending on topology.
If inputs are f1 and f2: f Σ = f 1 + f 2 , f Δ = ∣ f 1 − f 2 ∣ f_{\Sigma} = f_1 + f_2, \quad f_{\Delta} = |f_1 - f_2| f Σ = f 1 + f 2 , f Δ = ∣ f 1 − f 2 ∣
Heterodyning is the process of mixing to translate a signal from one frequency to another. The superheterodyne receiver is named for this: RF is mixed with a local oscillator (LO) to create a fixed intermediate frequency (IF) that is easy to filter and amplify.
Superhet conversion (conceptual)
- High-side LO example Math
- RF signal f_RF
- Local oscillator f_LO > f_RF
- Difference product (IF) f_IF = f_LO − f_RF
- Sum product f_LO + f_RF (filtered out)
- | Low-side LO | f_IF = f_RF − f_LO |
Image frequency: another RF that also mixes to the same IF. Image rejection is why preselectors and high first IFs exist—preview of receiver chapters, but the mixer sum/difference idea starts here.
Mixer types you will see named
- Type Notes
- Diode ring / doubly balanced mixer Strong LO, good balance, common RF brick
- Switching / commutating mixer FETs or Gilbert cell; LO as switch drive
- Transistor single-ended mixer Simple; more spurs
- Product detector Mixer used as SSB/CW demodulator with BFO/carrier
- Worked example — IF generation
Marine channel RF 156.8 MHz , LO 146.3 MHz (teaching numbers): f Δ = 156.8 − 146.3 = 10.5 M H z ( I F ) f_{\Delta} = 156.8 - 146.3 = 10.5\,\mathrm{MHz} \quad (\mathrm{IF}) f Δ = 156.8 − 146.3 = 10.5 MHz ( IF ) f Σ = 156.8 + 146.3 = 303.1 M H z ( f i l t e r e d a w a y ) f_{\Sigma} = 156.8 + 146.3 = 303.1\,\mathrm{MHz} \quad (\mathrm{filtered\, away}) f Σ = 156.8 + 146.3 = 303.1 MHz ( filtered away )
Same LO on transmit chains can up-convert a modulated IF to the antenna frequency—mixers are bidirectional spectral tools, not “RX only” parts.
How the four blocks cooperate on one radio
Walk a modern synthesized VHF transceiver:
Reference oscillator (TCXO) feeds the PLL .
PLL locks a VCO to N × f_ref → channelized LO .
Mixer combines LO with incoming RF → IF .
Op amps condition audio, AGC voltages, and squelch analog paths after detection.
- Block One-line Element 3 identity
- Op amp High-gain differential amp; closed-loop gain set by feedback resistors
- Inverting amp Gain −Rf/Rin; virtual ground at − input
- Non-inverting amp Gain 1 + Rf/Rg
- VCO f_out controlled by voltage
- PLL PD + filter + VCO; lock/capture to reference
- Mixer Sum and difference products; heterodyning
- Exam-day checklist for op amps, PLLs, VCOs, mixers
Ideal op-amp: infinite gain, infinite Zin, zero Zout (analysis model).
Inverting: −Rf/Rin ; non-inverting: 1 + Rf/Rg .
Virtual ground on the classic inverter’s summing junction.
PLL locks VCO to reference via phase detect + loop filter.
Lock holds; capture acquires—capture often narrower.
VCO = voltage steers frequency.
Mixer → sum and difference ; superhet IF = |LO ± RF| chosen product.
With tanks from §10.1 and these active blocks, you can describe how a radio both selects a frequency and generates/translates it. The final section of this chapter teaches you to read the schematic and signal-flow path that wires all of those pieces together.
- The direct digital synthesizer block chain (name every block)
- Sub-topic 3-D-031 asks which frequency synthesizer circuit uses a phase comparator,
- look-up table, digital-to-analog converter, and a low-pass antialias filter . The
- answer is a direct digital synthesizer (DDS) — and the value of the question is
- that it names the whole chain. Candidates who can say "DDS uses a look-up table and a
DAC" still miss it, because they stop before the filter.
Block What it does
Phase comparator / accumulator Advances a phase value by a fixed increment on every clock tick; the increment sets the output frequency
- Look-up table Converts each phase value into the corresponding amplitude of a sine wave
- Digital-to-analog converter (DAC) Turns that amplitude number into a stepped analogue voltage
- Low-pass anti-alias filter Smooths the steps and removes the sampling images above the Nyquist frequency
- The anti-alias filter is not optional cosmetics. A DAC clocked at f_clk produces
- not only the wanted output but mirror images at f_clk ± f_out, 2f_clk ± f_out and so
- on. Without the low-pass filter those images leave the synthesizer as real, radiated
spurious emissions.
In a direct digital synthesizer, what are the unwanted components on its output?
Spurs at discrete frequencies. Note the contrast the pool draws with the PLL: what spectral impurity components might be generated by a phase-locked-loop
synthesizer? Broadband noise. Two different synthesizers, two different failure
signatures:
- Synthesizer Characteristic impurity
- DDS Spurs at discrete frequencies — from DAC quantisation, truncation of the phase word, and residual images
- PLL Broadband noise — phase noise skirts around the carrier
- That distinction is directly useful on a spectrum analyzer: discrete pickets either
side of the carrier point at a DDS; a raised noise pedestal points at a PLL.