Study guide

10.1 R-L-C Resonant Circuits

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

10.1 R-L-C Resonant Circuits

Key Takeaways Explain This Topic AI

Series resonance occurs when XL = XC; impedance is minimum and equal to R, and circuit current is maximum for a given source voltage

Parallel (tank) resonance presents maximum impedance and minimum line current at f0; RF amplifier collector/drain tanks use this high-Z peak

Resonant frequency for ideal series or parallel LC is f0 = 1/(2π√(LC))

Quality factor Q measures sharpness; bandwidth BW = f0/Q between the half-power (−3 dB) frequencies

Higher Q means narrower bandwidth and greater selectivity; losses (series R or tank loading) lower Q and widen BW

Last updated: August 2026

10.1 R-L-C Resonant Circuits

Quick Answer: f0 = 1/(2π√(LC)) . Series resonance: XL = XC , |Z| minimum (= R) , current maximum . Parallel (tank) resonance: |Z| maximum , line current minimum . Q measures sharpness; BW = f0/Q between the half-power points. High-Q tanks and IF filters are narrow ; low-Q networks are wide .

Topic 3-D (practical circuits) starts where pure impedance formulas left off. Element 3 already taught you that series RLC magnitude is √[R² + (XL − XC)²] and that XL and XC cancel at one frequency. This section turns that cancelation into resonant-circuit behavior —the language of RF tanks, traps, IF transformers, and tuned amplifiers that GROL maintainers align and repair every day.

Why resonance matters on a radio chassis

Almost every transmitter final, receiver RF/IF stage, crystal filter skirt, and antenna matching network exploits resonance : a frequency where inductive and capacitive reactances balance so the network stops looking “reactive” and starts looking like a pure resistance—either very small (series) or very large (parallel). Select the wrong L or C, load the tank too heavily, or mistune the slug, and you lose power, gain, or adjacent-channel rejection.

  • Role in gear Topology you usually meet What you want at f0
  • Oscillator or RF amp collector/drain load Parallel LC tank High impedance (voltage peak)
  • Series trap / some matching arms Series LC Low impedance (shunt path or pass path)
  • IF filter / bandpass Cascaded tuned circuits Controlled Q and BW
  • Antenna tuner Series/parallel L-network Cancel antenna reactance; present ~50 Ω
  • Resonant frequency — one formula, two topologies

For ideal inductance L and capacitance C (series or parallel): f 0 = 1 2 π L C f_0 = \frac{1}{2\pi \sqrt{LC}} f 0 ​ = 2 π L C ​ 1 ​

  • Symbol Unit Notes
  • f0 hertz (Hz) Often kHz or MHz in radio work
  • L henrys (H) µH and mH common
  • C farads (F) pF and nF common

Pool-style check: If L doubles, f0 falls by √2 ≈ 0.707. If C is cut to one-fourth, f0 doubles. Powers-of-ten errors (µH vs mH, pF vs nF) create the classic wrong answers of 1.59 MHz vs 5.03 MHz vs 15.9 MHz on numeric stems.

Worked example — IF-style tank

L = 250 µH , C = 100 pF (rough 1 MHz IF ballpark teaching set): L C = ( 250 × 10 − 6 ) ( 100 × 10 − 12 ) = 2.5 × 10 − 14 = 1.581 × 10 − 7 \sqrt{LC} = \sqrt{(250 \times 10^{-6})(100 \times 10^{-12})} = \sqrt{2.5 \times 10^{-14}} = 1.581 \times 10^{-7} L C ​ = ( 250 × 1 0 − 6 ) ( 100 × 1 0 − 12 ) ​ = 2.5 × 1 0 − 14 ​ = 1.581 × 1 0 − 7 f 0 = 1 2 π × 1.581 × 10 − 7 ≈ 1.01 M H z f_0 = \frac{1}{2\pi \times 1.581 \times 10^{-7}} \approx 1.01\,\mathrm{MHz} f 0 ​ = 2 π × 1.581 × 1 0 − 7 1 ​ ≈ 1.01 MHz

Trim C or L slightly (slug-tuned coil, ceramic trimmer) and the stage tracks the assigned IF channel.

Worked example — HF transmitter tank scale

L = 5 µH , C = 200 pF : f 0 = 1 2 π 5 × 10 − 6 × 200 × 10 − 12 = 1 2 π 10 − 15 ≈ 5.03 M H z f_0 = \frac{1}{2\pi \sqrt{5 \times 10^{-6} \times 200 \times 10^{-12}}} = \frac{1}{2\pi \sqrt{10^{-15}}} \approx 5.03\,\mathrm{MHz} f 0 ​ = 2 π 5 × 1 0 − 6 × 200 × 1 0 − 12 ​ 1 ​ = 2 π 1 0 − 15 ​ 1 ​ ≈ 5.03 MHz

Same √(LC) math as earlier impedance chapters—Element 3 loves recycling the 10 µH / 100 pF → ~5 MHz family of numbers with small L/C swaps.

Series RLC resonance — minimum Z, maximum current

In a series R–L–C loop driven by a voltage source: ∣ Z ∣ = R 2 + ( X L − X C ) 2 |Z| = \sqrt{R^2 + (X_L - X_C)^2} ∣ Z ∣ = R 2 + ( X L ​ − X C ​ ) 2 ​

At resonance XL = XC , so: ∣ Z ∣ m i n = R |Z|_{\mathrm{min}} = R ∣ Z ∣ min ​ = R

  • Quantity at series f0 Behavior
  • Net reactance Zero
  • Impedance Minimum = R only
  • Current (fixed V) Maximum
  • Phase (ideal) Voltage and current in phase (resistive)
  • Voltage across L (or C) Can be much larger than source V (Q magnification)

Exam hook you must not miss: impedance of a series RLC circuit at resonance is equal to the resistance only —not zero (unless R = 0), not XL, not XC.

Current and “Q magnification”

If source voltage is V and R is the only remaining impedance, I = V/R is maximum. That large current through XL (or XC) produces a reactive voltage I × XL that can be Q times the source voltage across L or C alone. Series circuits can therefore develop high voltages on L and C even when the generator is modest—useful for traps and dangerous for insulation if Q is high and R is tiny.

Series applications in radio practice

Series traps across a line: near-zero Z at the trap frequency shorts that frequency to ground (or across a path), notching an interferer.

Series arms in L-match networks: cancel antenna reactance so the transmitter sees resistance.

Some crystal and ceramic filter models include series-resonant paths that pass the desired band.

Parallel RLC (tank) resonance — maximum Z, minimum line current

A parallel combination of L and C (with loss resistance modeled in series with L or as a parallel R) is the classic tank circuit . At resonance the circulating current between L and C is large, but the net current drawn from the source is small—the tank looks like a high impedance .

  • Quantity at parallel f0 Behavior
  • Impedance Maximum (high Z)
  • Line / feed current Minimum
  • Circulating tank current High (energy sloshes L ↔ C)
  • Phase (ideal) Resistive at the terminals
  • RF amp use Collector/drain load peaks voltage gain at f0

Why RF amplifiers love tanks: a transistor wants a high load impedance at the operating frequency for voltage gain, and a low impedance off-frequency to reject harmonics and out-of-band noise. A parallel tank delivers exactly that peak.

Idealized parallel vs real tanks

Ideal lossless parallel LC would present infinite Z at f0. Real coils have series resistance; solid-state stages load the tank; coupling loops steal energy. Finite loaded Q keeps peak Z finite—still “high,” still the right mental model for Element 3: parallel resonance → high impedance .

  • Topology Z at f0 Line current at f0 Typical RF job
  • Series RLC Min (= R) Max Trap, series match
  • Parallel RLC tank Max Min Oscillator/amp load, IF transformer primary
  • Quality factor Q — sharpness of resonance

Q is the dimensionless figure of merit for how “peaky” the resonance is.

Series RLC definitions (exam-useful forms) Q = X L R = X C R = 2 π f 0 L R = 1 2 π f 0 C R Q = \frac{X_L}{R} = \frac{X_C}{R} = \frac{2\pi f_0 L}{R} = \frac{1}{2\pi f_0 C R} Q = R X L ​ ​ = R X C ​ ​ = R 2 π f 0 ​ L ​ = 2 π f 0 ​ CR 1 ​

(at resonance, XL = XC, so either reactance over R works).

Parallel tank (loaded) intuition

For a parallel tank with parallel resistance R_p representing losses and loading: Q ≈ R p X L = R p X C Q \approx \frac{R_p}{X_L} = \frac{R_p}{X_C} Q ≈ X L ​ R p ​ ​ = X C ​ R p ​ ​

Heavy loading (small R_p) destroys Q . That is why an IF can of a marine receiver is carefully coupled: too much load flattens the response and adjacent-channel junk comes through; too little coupling starves the next stage of signal.

  • High Q Low Q
  • Sharp peak Broad peak
  • Narrow bandwidth Wide bandwidth
  • High selectivity Poor selectivity / flatter passband
  • Higher circulating voltages/currents for given energy More damped, less ringy
  • Bandwidth — BW = f0 / Q

The half-power bandwidth (also called the −3 dB bandwidth) of a single tuned circuit is: B W = f 0 Q BW = \frac{f_0}{Q} B W = Q f 0 ​ ​

where BW = f_H − f_L, and f_H and f_L are the upper and lower frequencies at which power in the load is half the resonant value (voltage ≈ 0.707 of peak for a constant-resistance load model).

  • Given Find
  • f0 and Q BW = f0/Q
  • f0 and BW Q = f0/BW
  • Need more selectivity Raise Q or cascade tuned stages
  • Need flatter, wider passband Lower loaded Q (more loading / damping)
  • Worked example — IF filter bandwidth

f0 = 455 kHz , Q = 50 : B W = 455 k H z 50 = 9.1 k H z BW = \frac{455\,\mathrm{kHz}}{50} = 9.1\,\mathrm{kHz} B W = 50 455 kHz ​ = 9.1 kHz

That order of magnitude suits AM voice-style IF widths. Raise Q to 100 and BW halves to 4.55 kHz —tighter, more selective, less audio “room” if overdone.

Worked example — VHF channel-style thinking

f0 = 156.8 MHz (marine VHF Ch-16 ballpark), desired BW ≈ 25 kHz for a simple single-circuit teaching model: Q = f 0 B W = 156.8 × 10 6 25 × 10 3 ≈ 6272 Q = \frac{f_0}{BW} = \frac{156.8 \times 10^6}{25 \times 10^3} \approx 6272 Q = B W f 0 ​ ​ = 25 × 1 0 3 156.8 × 1 0 6 ​ ≈ 6272

A single LC tank rarely holds that Q under real loading—modern radios use multiple poles , crystals, ceramics, or DSP filters. Element 3 still wants the BW = f0/Q relationship cold even when real hardware uses multi-stage filters.

  • Half-power points (mental picture) response
  • ^
  • | *
  • | * *
  • 0.707 -|------*---*------ half-power
  • | * *
  • | * *
  • +---+----+----+--> f
  • fL f0 fH
  • <─ BW ─>

Energy outside fL–fH is rejected more and more; that is selectivity .

Voltage and current vs frequency — what you measure on the bench

  • Sweep frequency through series RLC What meters show
  • Below f0 (XC > XL) Net capacitive; lower current than at f0
  • At f0 Current peaks; Z = R
  • Above f0 (XL > XC) Net inductive; current falls
  • Sweep frequency through parallel tank What meters show
  • Off resonance Lower Z; more line current
  • At f0 Line current dips; voltage across tank peaks (driven current source / high-Z driver)

When aligning an IF transformer with a sweep generator and scope, you are literally watching Q and BW: a tall skinny blob is high Q; a short wide blob is overcoupled or low Q.

Tank circuits in RF amplifiers and oscillators

Parallel tanks appear as:

Collector/drain loads in Class C or linear RF stages — peak impedance at the carrier; harmonics see lower Z and are attenuated.

Oscillator resonators (with feedback) — frequency set by LC (or crystal’s series/parallel modes).

IF transformers — double-tuned transformers set bandpass shape; coupling coefficient interacts with Q to produce single-peak or double-hump responses.

Design/maintain hooks for GROL techs:

  • Symptom Resonant-circuit thinking
  • Low TX power, tank cold Off-resonance, open L, shorted C, wrong band switch L
  • Broad, ratty RX selectivity Loaded Q collapsed; bad IF can, wet silver mica, damping fault
  • Oscillator off-frequency C shifted (temp, trimmer), core slug moved, load pulling Q/f0
  • Spurious/harmonic radiation Tank not rejecting harmonics; low Q or wrong harmonic trap
  • Series vs parallel — one-page comparison
  • Feature Series resonance Parallel (tank) resonance
  • XL vs XC at f0 Equal Equal (ideal)
  • Impedance Minimum (= R) Maximum
  • Line current (voltage drive) Maximum Minimum
  • Phase Resistive Resistive
  • Q (series form) XL/R Often R_p/XL when modeled parallel
  • BW f0/Q f0/Q
  • Classic radio use Traps, series match Amp/oscillator tanks, IF
  • Exam-day checklist for R-L-C resonance (3-D)

f0 = 1/(2π√(LC)) — same for ideal series and parallel LC.

Series: Z min = R ; current max .

Parallel tank: Z max ; line current min .

Q high → sharp , selective; BW = f0/Q .

Half-power points define BW; voltage ~0.707 of peak there in the standard model.

Loading a tank lowers Q , widens BW , lowers peak Z.

RF amp tanks are parallel ; do not answer “series minimum Z” for a collector tank question.

Master these extremes and the BW equation, and Element 3 resonant-circuit items stop being abstract AC math and become the same story you use when you dip a grid-dip meter, peak a plate current dip (legacy), or sweep an IF. Next section moves from passive tanks into op amps, PLLs, VCOs, and mixers —the active practical circuits that generate, lock, and translate those RF frequencies.