Study guide

20.3 Marine VHF, MF/HF & SSB-SITOR

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

20.3 Marine VHF, MF/HF & SSB-SITOR

Key Takeaways Explain This Topic AI

Marine VHF channel spacing is 25 kHz; maximum FM deviation is ±5 kHz; distress/calling is Channel 16; DSC is Channel 70

The USA–INT control changes some normally duplex channels into simplex channels for domestic/international channel-plan differences

Verify GPS/NMEA position into a DSC VHF by confirming lat/long (and related fields) on the radio display—not by holding the distress button

SITOR ARQ sends data in three-character blocks with interactive acknowledgements; ARQ is two-way, FEC is one-way to all stations, SFEC is one-way to a single station

FEC weather/safety broadcasts can be received without two-way contact; ARQ is the interactive ship–coast telex mode

Last updated: August 2026

20.3 Marine VHF, MF/HF & SSB-SITOR

Quick Answer: Marine VHF : 25 kHz channels, ±5 kHz deviation, Ch-16 distress/calling, Ch-70 DSC. USA–INT flips some duplex → simplex . Check GPS sentences by reading lat/long on the VHF display. MF/HF SSB : watch DC voltage under voice peaks; tuner leads to insulated backstays use GTO-15 . SITOR : ARQ = two-way 3-character blocks; FEC = one-way to all; SFEC = one-way to one station.

Topic 3-N (Marine) begins with the bridge and radio-room equipment GROL holders install and repair every day: VHF for coastal line-of-sight, MF/HF SSB for longer range, and SITOR/NBDP for maritime telex.

  • Marine VHF — channel plan and FM parameters
  • Channel spacing and deviation
  • Parameter Element 3 value
  • Channel spacing 25 kHz
  • Maximum allowable frequency deviation ±5 kHz
  • Modulation family (context) Angle-modulated voice ( F3E/G3E -class marine FM)

Do not import land-mobile 12.5 kHz narrowband spacing or ±2.5 kHz narrow deviation as the marine VHF pool answers—Element 3’s marine VHF items use 25 kHz and ±5 kHz .

Channel 16 vs Channel 70

  • Channel Function
  • 16 Distress and calling (voice radiotelephony)
  • 70 Digital Selective Calling and acknowledgement
  • Working channels (e.g. 68, 22A concepts) After contact, move off 16 for traffic

Memory split: 16 talks; 70 rings the digital doorbell. Never treat Ch-70 as a survival-craft voice channel (Element 1 already hammered that distinction).

USA–INT control

The USA–INT control or function changes some channels that are normally duplex channels into simplex channels . International (ITU) duplex pairs may be reassigned for U.S. domestic simplex or semi-duplex practices. The control is not a power booster and does not “increase range when set to INT.”

Setting concept Effect

International duplex plan Ship TX and ship RX on different frequencies for some public correspondence / coast links

USA plan / USA–INT switch Selected channels become simplex (same TX/RX frequency) for ship–ship or domestic use

When a radio “works on some channels but not others” after a voyage between regions, verify USA–INT before condemning the synthesizer.

Verifying GPS into a marine DSC VHF

How might an installer verify correct GPS sentence delivery to a marine DSC VHF ? Look for latitude and longitude, plus speed, on the VHF display (or the radio’s GPS status page showing valid position fields).

  • Good verification Bad idea
  • Lat/long (and SOG) present and updating on VHF Press and hold the red distress button to “test GPS”
  • DSC position field populated Ask random stations for a “position radio check” as the only test
  • NMEA/NMEA2000/status LED confirms fix Assume factory default always has GNSS

False distress alerts are a career-limiting shortcut. Use display status and manufacturer test modes.

MF/HF SSB — installation and transmit symptoms

Beyond VHF line-of-sight, ships use MF/HF single-sideband for voice ( J3E ) and data (SITOR/NBDP with F1B/J2B -class emissions depending on equipment).

Voice-test observation

A common occurrence when voice-testing an SSB aboard a boat : voltage panel indicator lamps may glow with each syllable . That flicker tracks speech envelope current demand on a shared DC bus—evidence the transmitter is drawing power on voice peaks, not proof the antenna is perfect.

Apparent low voltage on transmit

What might contribute to apparent low voltage on marine SSB transmitting? Pool answer emphasis: a blown black negative fuse (ground/return path open or high resistance) can make the bus look sick under load. Always verify both positive and negative high-current paths, crimps, and battery interconnects—not only the red feed fuse.

  • Symptom Checks
  • Lights dim / glow on syllables Normal peak current; confirm battery health and cable size
  • Low voltage / shutdown on key Fuses (incl. negative ), connections, battery capacity, charging
  • Tuner “hunting” constantly Antenna, ground plane/counterpoise, GTO lead, tuner
  • High SWR / no tune Insulators on backstay, feedpoint, corrosion
  • GTO-15 to an insulated backstay

What type of wire connects an SSB automatic tuner to an insulated backstay ? GTO-15 high-voltage cable —not RG-8/U or RG-213 coax as the tuner-to-radiator lead in the pool’s framing. Coax belongs on the transmitter-to-tuner side in typical installs; the high-voltage GTO-15 runs from tuner output up to the backstay feedpoint.

  • Segment Typical conductor
  • Radio → automatic tuner Coax (e.g. RG-213 family)
  • Tuner → insulated backstay / whip feed GTO-15 HV wire
  • RF ground / counterpoise Wide copper strap to sea ground / sintered plates per good practice
  • SITOR / NBDP — ARQ, FEC, and SFEC

SITOR provides reliable maritime teleprinter traffic over MF/HF. Element 3 tests mode behavior more than typing skill.

ARQ (SITOR-A) — interactive two-way

True statement: ARQ message transmissions are made in data groups consisting of three-character blocks . The information-sending station transmits a short block; the information-receiving station acknowledges (or requests repeat) continuously—not only at the end of a whole message. ARQ is not “time diversity FEC” and not a purely one-way mode.

  • ARQ property Fact
  • Directionality Two-way (interactive)
  • Block size cue Three-character blocks
  • Error strategy ACK/NAK style repeats
  • FEC and SFEC — one-way

The sequence ARQ, FEC, SFEC best corresponds to:

Two-way communications → one-way communications to all stations → one-way communications to a single station.

  • Mode Direction Audience
  • ARQ Two-way Ship ↔ coast (interactive telex)
  • FEC (SITOR-B collective) One-way All stations (broadcasts)
  • SFEC One-way Single addressed station
  • Receiving FEC without linking first

True statement: Two-way communication with the coast radio station using FEC is not necessary to be able to receive the broadcasts. Ships can copy FEC weather/safety telex without establishing an ARQ circuit first. Contrasting false ideas: that answerbacks must be exchanged before any FEC can be received; that ARQ sends each character twice as its defining method; that weather cannot use FEC because “doubling characters” would make broadcasts too long.

Emission and mode selection reminder

  • Traffic Typical mode selection
  • MF/HF voice J3E
  • TELEX / SITOR / NBDP F1B or J2B per manufacturer
  • VHF voice Marine FM channels (Ch-16, working channels)
  • VHF DSC Ch-70 digital
  • GMDSS-related radio tech at Element 3 depth

You are not sitting Element 7/9 here, but maintainers must see how boxes fit:

  • Function Equipment
  • Short-range distress voice VHF Ch-16
  • Short-range digital alerting VHF DSC Ch-70
  • Longer-range voice MF/HF SSB J3E (e.g. 2182 kHz distress concepts from Element 1)
  • Longer-range digital telex / MSI SITOR/NBDP ARQ/FEC; NAVTEX (next section)
  • Position into radios GNSS → NMEA sentences into DSC controllers
  • Service checklist (085–086)

Measure channel spacing / deviation with service monitors when aligning VHF.

Prove Ch-16 voice and Ch-70 DSC paths separately.

Document USA–INT setting for the vessel’s operating area.

Confirm GPS lat/long on the radio display after NMEA install.

On SSB: size DC cables, inspect negative fusing, use GTO-15 to backstays, maintain RF ground.

For SITOR: know ARQ = 3-char blocks, two-way ; FEC = broadcast receive without link ; SFEC = selective one-way .

Exam-day checklist (3-N 085–086)

VHF spacing 25 kHz ; deviation ±5 kHz .

16 = distress/calling; 70 = DSC.

USA–INT → some duplex channels become simplex .

GPS verify → lat/long (and speed) on display .

SSB voice-test → panel lamps may glow each syllable ; low voltage → check black negative fuse paths.

Tuner to insulated backstay → GTO-15 .

ARQ three-character blocks; ARQ/FEC/SFEC = two-way / all-stations one-way / single-station one-way .

FEC broadcasts receivable without prior two-way contact.

Next section covers survival craft electronics, weatherfax, NAVTEX, and NMEA data that feed and extend these radios.