Study guide
20.5 NMEA 0183 & NMEA 2000 Data Networks
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
20.5 NMEA 0183 & NMEA 2000 Data Networks
Key Takeaways Explain This Topic AI
NMEA 2000 is the bi-directional, multi-transmitter, multi-receiver data network; NMEA 0183 is the older single-talker, multi-listener standard
NMEA 0183 shielding is terminated to ground at the talker and left unterminated at the listener, so no ground loop is formed
If one device on an NMEA 2000 network fails, there is no interruption to the other devices
A load equivalence number (LEN) of 1 corresponds to 50 mA of current consumption
An NMEA 2000 system with devices in a single location may use an end-powered network, and a voltage drop of 1.5 volts at the end of the last segment satisfies the cabling plan
Last updated: August 2026
20.5 NMEA 0183 & NMEA 2000 Data Networks
Quick Answer: NMEA 2000 is the bi-directional, multi-transmitter, multi-receiver network. NMEA 0183 shields are grounded at the talker, unterminated at the listener . On NMEA 2000, one failed device does not interrupt the others . LEN 1 = 50 mA. Devices in one location may use an end-powered network , and 1.5 volts of drop at the last segment satisfies the cabling plan.
Sub-topic 3-N-089 (NMEA Data) is the most modern material in the Marine topic, and it is directly relevant work: a GROL technician installing a DSC VHF must get position data into it, and that is an NMEA job.
The two standards
- NMEA 0183 NMEA 2000
- Topology Single talker , multiple listeners Bi-directional, multi-transmitter, multi-receiver network
- Signalling Serial ASCII sentences, EIA-422 differential CAN bus, binary messages
- Typical rate 4,800 baud (38,400 for AIS "high speed") 250 kbit/s
- Wiring Point-to-point pairs Backbone with drops and terminators at both ends
- Power on the bus No Yes — the backbone carries 12 V
What data language is bi-directional, multi-transmitter, multi-receiver network? NMEA 2000. The three adjectives in that question are the discriminator. NMEA 0183 is fundamentally one-way : a talker transmits and listeners listen, and a second talker on the same pair simply collides.
Shielding NMEA 0183
How should shielding be grounded on an NMEA 0183 data line? Terminated to ground at the talker and unterminated at the listener.
This is the classic single-point grounding rule, and the reasoning is worth carrying to every shielded run you install. Ground a shield at both ends and you create a ground loop : the two ends of a vessel are rarely at exactly the same potential, so current flows along the shield. That current couples noise straight into the signal pair — the shield stops being a shield and becomes an interference injector.
Grounding at one end only — the talker — gives the shield somewhere to drain the charge it intercepts without providing a return path for loop current.
- Shield grounding Result
- Talker end only Correct — drains interference, no loop
- Both ends Ground loop; noise injected into the signal
- Listener end only Works less well; convention and the pool specify the talker
- Neither end Shield floats and does nothing
- NMEA 2000 fault tolerance
What might occur in NMEA 2000 network topology if one device in line should fail? There will be no interruption to all other devices.
This is the payoff of the backbone-and-drop architecture. Devices hang off the backbone on short drop cables through tee connectors; they do not sit in the data path. A failed chartplotter, a flooded transducer, an unplugged instrument — the backbone carries on.
Contrast a genuine daisy chain, where the signal passes through each device and any failure severs everything downstream. Two things do still take the whole network down, and they are worth knowing:
A missing or failed terminating resistor at either end of the backbone (120 Ω each) — reflections corrupt the bus.
A short on the backbone itself , which takes out both data and power.
Load equivalence numbers and power
In an NMEA 2000 device, a load equivalence number (LEN) of 1 is equivalent to how much current consumption? 50 mA.
LEN is a simple budgeting unit: 1 LEN = 50 mA . Every certified device is marked with its LEN, so an installer can add them up instead of hunting through data sheets:
- Total LEN Current draw
- 1 50 mA
- 5 250 mA
- 10 500 mA
- 20 1 A
A standard "light" backbone supports a limited total LEN; exceeding it means moving to heavy cable, adding a second power insertion point, or splitting the network with a bridge.
An NMEA 2000 system with devices in a single location may be powered using this method: an end-powered network. When every device is clustered together, feeding power in at one end of the backbone is acceptable. Spread devices along a long backbone and you insert power in the middle instead, halving the worst-case run length and therefore halving the voltage drop.
What voltage drop at the end of the last segment will satisfy NMEA 2000 network cabling plans? 1.5 volts.
That is the budget. Devices are specified to work down to about 9 V; a 12 V nominal supply less 1.5 V of drop still leaves ample margin. Because drop is I × R , the levers are total current (LEN), cable resistance (light versus heavy backbone), and run length — which is exactly why the power-insertion decision above matters.
Why this reaches Element 1
Section 4.6 and section 19.8 both turn on the same practical point: a DSC VHF needs position data , and on a modern vessel that data arrives over NMEA. If the network is mis-wired — shield grounded at both ends, a missing terminator, too much voltage drop at the far end — the DSC radio may show no position, and a distress alert then goes out without the single most valuable field it can carry.