Study guide

20.2 Signal Processing, Software & Codes

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

20.2 Signal Processing, Software & Codes

Key Takeaways Explain This Topic AI

SDR means Software Defined Radio—many transceiver functions (filtering, modulation, detection) implemented in software rather than fixed hardware

DSP in a modern radio can control frequency, modulation, and detection, but does not control SWR (SWR is an antenna/feedline quantity)

GMDSS DSC uses a 10-bit error-correcting code with data bits followed by a 3-bit error-correcting field

SITOR-A/B characters are 7 bits with 4 zeros and 3 ones; Idle Signal (a) 0000111 is FEC Phasing Signal 1

High-level data modes (Morse, RTTY/Baudot, ASCII, packet) and selective-calling codes sit on top of RF modulation—know which layer fails when symbols garble

Last updated: August 2026

20.2 Signal Processing, Software & Codes

Quick Answer: SDR = Software Defined Radio . DSP filters, demodulates, and can steer frequency / modulation / detection —but not SWR . DSC code = 10-bit error-correcting characters ( data bits + 3-bit ECC). SITOR characters = 7 bits with 4 zeros + 3 ones . Idle Signal (a) = 0000111 = FEC Phasing Signal 1 . Modes: Morse, RTTY, ASCII, packet ride on RF; selective calling addresses stations digitally.

Key topic 084 is the software and coding layer of Topic 3-M. If §20.1 explained how channels are shared , this section explains how bits and algorithms process the signal once it is digitized .

  • Software Defined Radio (SDR)
  • Definition

SDR means Software Defined Radio —not “software deviation ratio,” “SWR meter,” or “static dynamic RAM.” In an SDR, many functions that older designs built with crystals, discrete IF filters, and analog detectors are implemented as software (embedded firmware, FPGA fabric, or a PC host) operating on digitized samples.

  • Traditional radio Software-defined approach
  • Fixed crystal / mechanical filters Configurable digital filters
  • Hardware modulator/demodulator per mode Algorithms selected by software
  • Mode change often means hardware option boards Mode change can be a firmware load
  • Alignment pots for every IF stage Calibration constants and DSP parameters
  • Why GROL techs still matter

SDR does not eliminate RF craftsmanship:

The antenna, feedline, and front-end still determine noise figure, IMD, and SWR .

Clock quality, ADC overload, and shielding still cause “DSP ghosts.”

Illegal emissions still come from bad amplifiers and mixers—even if the waveform was “perfect” in software.

When a customer says “the software radio is broken,” separate RF path failures from firmware/configuration failures before swapping expensive boards.

Digital signal processing (DSP) — what it does and does not do

DSP samples an analog waveform (or processes already-digital baseband) and applies algorithms: filtering, noise reduction, demodulation, AGC, squelch logic, and modulation synthesis.

Pool fact: what DSP does not control

In a modern DSP radio, DSP can be described as controlling:

  • Frequency (tuning / LO programming concepts),
  • Modulation , and
  • Detection (demodulation),

but DSP does not control SWR . Standing-wave ratio is a property of the antenna system and feedline match , outside the DSP core. No amount of clever filtering will turn a disconnected whip into a 1:1 load.

  • Function DSP involved? Notes
  • IF/AF digital filtering Yes Notch, bandpass, noise reduction
  • Demodulation (AM/FM/SSB/digital) Yes Detection algorithms
  • Modulation synthesis Yes Waveform generation
  • Display of SWR from a sensor Indirect readout only Sensor is external to “DSP controls SWR”
  • Actual antenna match No Tuner, antenna, coax
  • Filtering and demodulation literacy

Think of the classic receiver chain (Ch12) with a digital middle:

RF front end still filters images and strong out-of-band signals.

ADC digitizes IF or baseband.

DSP implements sharp filters that would be bulky as analog crystal banks.

Demodulator code recovers audio or bits.

DAC (or digital audio link) drives the speaker or data port.

Advantage of DSP filters vs pure analog: flexible bandwidth, adaptive notches, and reproducible performance without aging inductors. Limitation : garbage-in from a saturated front end is still garbage-out.

High-level data modes: Morse, RTTY, ASCII, packet

Element 3 does not require you to send perfect Morse on exam day, but it expects you to place codes on the right “layer” of the system.

  • Mode / code What it is Radio context
  • Morse (CW) On/off keyed characters A1A-class emissions; still used for identification and some backup links
  • RTTY Radioteletype; historically Baudot 5-bit characters FSK / AFSK over HF; ancestor of modern NBDP

ASCII 7-bit (commonly stored as 8-bit) computer character set Widest acceptance for computer-to-computer data exchange (Topic 083)

Packet Framed packets with headers, payloads, error checks OSI physical + link layers; AX.25-style radio packet thinking

Troubleshooting map

  • Symptom Likely layer
  • No RF carrier / wrong frequency Transmitter, LO, antenna
  • Strong RF but nonsense characters Demod, shift, polarity, baud rate
  • Good characters but wrong meaning Code set (Baudot vs ASCII), language tables
  • Intermittent frames, retries Link-layer ARQ, multipath, collisions
  • Selective calling codes — DSC and GMDSS digital calling

Digital Selective Calling (DSC) is the automated digital calling system used with GMDSS radios (VHF Ch-70, MF/HF DSC frequencies). Element 3 focuses on the character code , not the entire SOLAS carriage matrix.

DSC code structure (pool wording)

The code used for GMDSS-DSC transmissions is best described as a 10-bit error-correcting code starting with bits of data followed by a 3-bit error-correcting field.

Reject distractors:

  • 10-bit code that starts with the 3-bit ECC then 7 data bits (order reversed),
  • Simple 8-bit with one parity bit only,
  • 7-bit code merely “transmitted twice.”
  • Item Pool fact
  • Total character length concept 10-bit error-correcting code
  • Structure Data bits then 3-bit error-correcting code
  • Purpose Detect/correct errors so distress and routine digital calls remain reliable
  • Selective calling in the larger picture

Selective calling lets a coast station or ship address a specific MMSI (or group/all-ships categories) without requiring continuous voice watch on every possible working channel. For the GROL maintainer:

Verify MMSI programming and GNSS position input to the DSC controller.

Confirm the Ch-70 or MF/HF DSC RF path (antenna, duplexers, dedicated DSC receivers).

Remember: DSC is not the same as SITOR telex and not the same as NAVTEX—even though all are “digital maritime.”

SITOR character coding (bridge into marine NBDP)

SITOR (Simplex Teletype Over Radio) / NBDP (Narrow-Band Direct Printing) is the maritime telex family. Element 3 stores two hard coding facts under 084:

Character composition

The code used for SITOR-A and SITOR-B transmissions: each character consists of 7 bits with 4 zeros and 3 ones (constant-ratio code). Receivers use the 4/3 balance as a first error check.

  • Mode family Character rule to memorize
  • SITOR-A / SITOR-B 7 bits : 4 zeros + 3 ones
  • Not the answer 5-bit Baudot alone as the SITOR code description
  • Not the answer 7 data bits + 3 separate ECC bits (that pattern is closer to other systems)
  • Idle Signal (a) and FEC phasing

Which statement is true in the pool’s control-signal set? Idle Signal (a) (0000111) is used for FEC Phasing Signal 1 .

Memorize the bit string 0000111 with the label Idle Signal (a) / FEC Phasing Signal 1 . Do not invent that Signal Repetition or Control Signal 1 “is always” the FEC phasing answer when the stem asks for Idle Signal (a).

Codes and modes at a glance

  • System Element 3 coding takeaway
  • Computer data interchange ASCII widest acceptance
  • GMDSS DSC 10-bit ECC code; data then 3-bit ECC
  • SITOR-A/B characters 7 bits , 4 zeros / 3 ones
  • SITOR FEC phasing cue Idle Signal (a) 0000111 = Phasing Signal 1
  • GSM voice compression RPE CODEC (from §20.1)
  • P25 Phase 2 voice AMBE CODEC
  • Packet structure Physical TX; link framing
  • Maintainer workflow: software radio + coded emissions

Confirm RF health first — power, frequency, SWR, antenna. DSP cannot “software away” a bad match.

Confirm mode and code — J3E voice vs F1B/J2B telex vs DSC; wrong mode yields perfect RF and unreadable traffic.

Confirm identity programming — MMSI, answerbacks, EPIRB hex ID (survival gear in §20.4).

Use built-in self-tests for DSC/controllers; avoid live distress alerts for curiosity.

Document firmware versions on SDR platforms—field “regressions” are often config loads, not blown finals.

Exam-day checklist (3-M 084)

SDR = Software Defined Radio.

DSP: frequency / modulation / detection yes ; SWR no .

DSC: 10-bit error-correcting code; data bits followed by 3-bit ECC.

SITOR: 7-bit characters with 4 zeros and 3 ones .

Idle Signal (a) 0000111 → FEC Phasing Signal 1 .

Place Morse / RTTY / ASCII / packet on the correct functional layer when troubleshooting.

Selective calling = addressed digital call (DSC), not voice shouting a ship’s name on Ch-16 (though voice remains the follow-on).

When software, DSP limits, and the DSC/SITOR bit rules are cold-memorized, Topic 3-M is complete. Topic 3-N applies the same thinking to marine VHF, MF/HF SSB, and SITOR operations .